• Smart Structures and Systems
• /
• v.29 no.4
• /
• pp.617-624
• /
• 2022

A new intelligent adaptive control scheme was proposed that combines the control based on interference observer and fuzzy adaptive s-curve for flight path tracking control of unmanned aerial vehicle (UAV). The most important contribution is that the control configurations don't need to know the uncertainty limit of the vehicle and the influence of interference is removed. The proposed control law is an integration of fuzzy control estimator and adaptive proportional integral (PI) compensator with input. The rated feedback drive specifies the desired dynamic properties of the closed control loop based on the known properties of the preferred acceleration vector. At the same time, the adaptive PI control compensate for the unknown of perturbation. Additional terms such as s-surface control can ensure rapid convergence due to the non-linear representation on the surface and also improve the stability. In addition, the observer improves the robustness of the adaptive fuzzy system. It has been proven that the stability of the regulatory system can be ensured according to linear matrix equality based Lyapunov's theory. In summary, the numerical simulation results show the efficiency and the feasibility by the use of the robust control methodology.

• Journal of applied mathematics & informatics
• /
• v.40 no.1_2
• /
• pp.47-59
• /
• 2022

This paper concerns the problem of simultaneous fault detection and disturbance reject control(SFDDRC) for a class of linear time-invariant system. In the framework of fault detection, residual generators are required to be robust to disturbances existing in the system. Different from most of the existing simultaneous fault and control(SFDC) methods, SFDDRC rejects the influences of disturbances on residual generators by disturbance observer-based control(DOBC). This not only effectively improves the accuracy of fault detection, but also solves the problem that most of the existing SFDC methods require that the disturbance must be bounded. Finally, a numerical example is given to verify the validity of the method.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.270-273
• /
• 1996

A scheme of observer-based MFAC(Model Following Acceleration Control) system is proposed for the robustness control of DC servo position control systems. The proposed system is composed of LMFC, variable structure feedback controller, and reduced-order state observer. As the servo motor is controlled by the acceleration command, the total servo system becomes the acceleration control system. Simulation results show that the proposed system have robust properties against parameter variations and external disturbances.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1389-1399
• /
• 2013

A discrete controller is designed for low power dc-dc switched mode power supplies. The approach is based on time domain and the control loop continuously and concurrently tunes the compensator parameters to meet the converter specifications. A digital state feedback control combined with the load estimator provides a complete compensation, which further improves the dynamic performance of the closed loop system. Simulation of digitally controlled Buck converter is performed with MATLAB/Simulink. Experimental results are given to demonstrate the effectiveness of the controller using LabVIEW with a data acquisition card (model DAQ Pad - 6009).

• Journal of Mechanical Science and Technology
• /
• v.18 no.4
• /
• pp.535-549
• /
• 2004

This paper proposes a sliding mode controller with fuzzy adaptive perturbation compensator(FAPC) to get a good control performance and reduce the chatter, The proposed algorithm can reduce the chattering because the proposed fuzzy adaptive perturbation compensator compensates the perturbation terms. The compensator computes the control input for compensating unmodeled dynamic terms and disturbance by using the observer-based fuzzy adaptive network(FAN) The weighting parameters of the compensate. are updated by on-line adaptive scheme in order to minimize the estimation error and the estimation velocity error of each actuator. Therefore, the combination of sliding mode control and fuzzy adaptive network gives the robust and intelligent routine to get a good control performance. To evaluate the control performance of the proposed approach, tracking control is experimentally carried out for the hydraulic motion platform which consists of a 6-DOF parallel manipulator.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.1-6
• /
• 2003

The torque is an important measure that represents the performance of a particular engine. Furthermore the information of engine torque can be used as a primary feedback parameter in modem engine management system. In this paper, a methodology is proposed for torque estimation of SI-engine. Since the proposed method uses cylinder pressure sensor, the torque can be estimated in a simple manner. The indicated torque is estimated from the peak pressure and its location, and the load torque is observed by the state observer based on the estimated indicated torque. The proposed method is accurate and robust against the variations that affect the torque production such as spark timing, mass air flow and others. This torque estimation method may be an alternative solution to the use of engine torque maps in a modem torque-based engine management system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.2
• /
• pp.135-143
• /
• 1992

A novel sliding mode control with disturbance observer for position control of DC servo motor is presented. The conventional sliding mode controller changes the control structure depending on the state of switching surface and consequently, the control law is discontinuous and theoretically chatters at an infinite frequency. To overcome this problem in view of the practical implementation, the disturbance observer is used to compensate the effects of the parameter variations and the load disturvances. We can obtain the performance predetermined by the switching surface with continuous control law while the controlled system remains robust. The performance of the proposed controller with that of the conventional sliding mode controller through digital computer simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.497-499
• /
• 1999

This paper considers enhancing the robustness of a MIMO(Multi-Input Multi-Output) predictive control system. The characteristic polynomial matrix of the closed-loop is shown to consist of two factors $P_c$ and T, where $P_c$ is determined by the tuning knobs of the predictive controller and T is an observer or prefilter polynomial matrix. The robust stability condition is derived in terms of $P_c$ and T. A guideline on the selection of T is then presented for open-loop stable processes.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.239-242
• /
• 1998

Most of time delay existing in industrial processes can be modeled as an input time-delay which causes a lot of difficulties. To implement a time-delay free control, loop transfer function is recovered through the direct state feedback. For the proper state feedback, and observer is designed based upon the factorization approach which is known as one of the most powerful tool for the design of various control systems. The design scheme is parctically applied for the control of a DC motro which suffers from input time-delay. Simulational results demonstrate that this new algorithm guarantess the stability of the time-delayed system, as well as performance improvement compared to the conventional PI control.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.540-543
• /
• 1999

This paper describes a speed sensorless algorithm for vector control system with compensated stator resistance and rotor time constant of induction motor using a model reference adaptive system(MRAS). The system are composed of two MRAC, one is a rotor speed estimation and a stator resistor identification by back-EMF observer, other is used to identify rotor time constant by magnetizing current observer, so that the estimation can be cover a very low speed range with a robust control. The suggest control strategy and estimation method have been validated by simulation study. In the simulation using Matlab/Simulik, the proposed speed sensorless vector control system are shown to operate very well in spite of variable rotor time constant and load fluctuation.