• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.5
• /
• pp.371-378
• /
• 2015

In this paper, a different type of pulse width modulation (PWM) control scheme for a buck converter is introduced. The proposed buck converter uses PWM with frequency hopping and a low quiescent.current low dropout (LDO) voltage regulator with a power supply rejection ratio enhancer to reduce high spurs, harmonics and output voltage ripples. The low quiescent.current LDO voltage regulator is not described in this paper. A three-bit binary-to-thermometer decoder scheme and voltage ripple controller (VRC) is implemented to achieve low voltage ripple less than 3mV to increase the efficiency of the buck converter. An internal clock that is synchronized to the internal switching frequency is used to set the hopping rate. A center frequency of 2.5MHz was chosen because of the bluetooth low energy (BLE) application. This proposed DC-DC buck converter is available for low-current noise-sensitive loads such as BLE and radio frequency loads in portable communications devices. Thus, a high-efficiency and low-voltage ripple is required. This results in a less than 2% drop in the regulator's efficiency, and a less than 3mV voltage ripple, with -26 dBm peak spur reduction operating in the buck converter.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.16-20
• /
• 1989

In this paper, we describe the optimal driving method and magnetic flux distribution of permanent magnet which enhance torque characteristics in small-sized 3-phase brushless DC motors. The disadvantages of conventional $120^{\circ}$ constant current drive method are torque ripple, switching noise and spike voltage due to the inductance of stator coil. This shortcommings can be avoided by the switching slew-rate of driving current which is called linear voltage driving method. The aim of this study is to analyze linear voltage driving method quantatively and to determine optimal drive current waveform through computer simulation. The selection of commutation angle and slew rate of a new driving current at switching instants makes torque ripple index minimize and average torque maximize. And the validity of this new driving method was assured by Fourier analysis. Considering two dimensional nonlinear magnetic flux distribution on the permanent magnet, we suggest optimal flux distribution according to the presented driving method which improves torque characteristics.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.27-33
• /
• 1997

In this paper, instantaneous controller of a single-phase PWM converter is realized using DSP. The stable PI gain of the input current and the DC link voltage control system is designed. The DC link voltage control system can be designed in continuous-time domain. But as for the input current control system, the descretizing effect cannot be ignored so it must be designed in descrete-time domain considering the calculation time. The capacitance estimating algorithm which can be acquired through the ripple voltage is proposed. By this algorithm the DC link capacitance can be estimated even under the transient state. Experimental results show the input power factor of 99.1% and the voltage variation rate of $\pm$5% according to the load variation.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.563-568
• /
• 1999

Generally the control method of wire feeding motor in welding machine has been used full-wave phase control method. The fire-angle control generates low frequency speed ripple, and it causes the output current ripple. So it results in the variation of welding condition and low welding performances such as spatter generation and bead state. For the purpose of welding performances improvement by speed controller in wire feeding motor, in this paper the constant speed control method for welding machine is proposed. The proposed system is composed of speed control loop and current control loop. As a result of experiment by using proposed constant wire feed experiment by using proposed constant wire feed speed controller, the output voltage and current waveform and metal transfer are maintained stably. And moreover the number of instantaneous short circuit occurrence is reduced remarkably.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.32-34
• /
• 2005

In this paper, an insertcore type PMLSM is proposed to improve the low thrust density of aslotless type PMLSM. Aneural network is applied to enhance thrust and to minimize the detent force caused by both the slot-teeth structure and end-effect. As the resultsof the optimal design, the thrust ripple rate is decreased conspicuously from 10.22[%] to 2.87[%] and the distortion factor of thrust form 5.82[%] to 1.65[%], respectively

• Journal of the Korean Society of Radiology
• /
• v.12 no.3
• /
• pp.373-379
• /
• 2018

The purpose of this study was to investigate quantitative data on the difference in breast entrance surface dose with changes in focus-film distance, patient posture (anteroposterior-posteroanterior), thoracic wall thickness, rib bone thickness, lung tissue thickness, tube voltage, and high-voltage rectification method in Whole Spine Scanography, which is necessary for the treatment of scoliosis patients. Given a tube voltage of 90 kVp, kerma of 0.1 mGy, focus-film distance of 260 cm, tube voltage ripple rate of 0, filter thickness of 3.5 mm, and thickness of patient's thoracic wall of 120 mm as an X-ray exposure condition, from the simulation results using the Simulation of X-ray Spectra program to confirm the reduction effect of breast entrance surface dose according to the patient's posture (AP and PA), there was a dose reduction effect in aluminum filter thickness of 2.6 times at 3.5 mm, 25.7 times the thoracic wall thickness at 120 mm, 1.43 times higher tube voltage, and 0 to 1.14 times the tube voltage ripple rate. The total dose reduction effect was about 109 times. In order to confirm the dose reduction effect of RANDO phantom posture (AP and PA), from the results of the measurements taken under the conditions that the focus-film distance was 260 cm, the tube voltage was 90 kVp, the tube current was 270 mA, the exposure time was 0.31 sec, and the tube voltage ripple rate of X-ray generators was 0, the entrance surface dose reduction effect of the breast in the PA position was found to be 20.56 times lower than that of the AP position.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.8-12
• /
• 2008

For the reduction of fabrication cost and process time of AC plasma display panel (PDP), indium tin oxide (ITO) layer was patterned as bus electrode using Nd:$YVO_4$ laser. In comparison with the chemically wet etched ITO patterns, laser ablated ITO patterns showed the formation of shoulders and ripple-like structures at the edge of the ITO lines. For the reduction of shoulders and ripple-like structures, pulse repetition rate and scan velocity of laser was changed. In addition, we analyzed a discharge characteristic of PDP test panel to observe how the shoulders and ripple-like structures influence on the PDP. Based on experimental results, the pattern etched at the 500 mm/s and 40 kHz was better than any other condition. From this experiment we could see the possibility of the laser direct patterning for the application to the patterning of ITO in AC-PDP.

• Journal of Communications and Networks
• /
• v.1 no.2
• /
• pp.81-85
• /
• 1999

The regrowth of OQPSK power spectral sidelobes from AM/AM and AM/PM amplifier nonlinearity is analyzed. The time-domain expression for amplifier output shows how spectral re-growth will depend on the cubic coefficient of the Taylor's series of the amplifier nonlinearity as well as input amplitude ripple. Closed form spectrum calculations show that the spectral sidelobes produced by AM/PM take the same form as those produced by AM/AM. The rate of growth of AM/PM sidelobes is, however, not as great as for AM/AM.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1061-1069
• /
• 1989

본 연구에서는 제조공정을 생략하고, 보다 최종제품의 형상에 가까운 직접압 연법을 실현하기 위한 기초적 연구로서 두개의 회전하는 로울 내부를 냉각하면서 쐐기형 노즐을 통하여 폭이 균일한 용탕을 직접 주입하는 실험방법에 의해서 얻어진 주편의 표면상태와 주조조건과의 관계에 대하여 논하며 또한 기계적성질에 대하여 검토한다.

• Proceedings of the Korea Database Society Conference
• /
• 2008.05a
• /
• pp.321-338
• /
• 2008

Information and communication industry, which shows rapid growth rate, is now leading the global economic growth, contributing a ripple effect on general business and economic structure. It is said that information and communication industry enables swift economic growth taking a role as a basic industry of information-oriented society. Especially, rapid technical innovation promotes mutual growth of other related industries and it is technology-intensive. The purpose of this research is to analyze the management efficiency of information and communication industry using DEA method, and finally suggest numerical value for inefficient organizations to improve their efficiency. CCR-I, BCC-I efficiency and RTS(Returns to scale) of 29 companies engaged in information and communication industry was evaluated. With the results, I suggested model companies for benchmarking in information and communication industry. To summarize, 7 companies were selected with CCR-I efficiency rate 1, and 12 companies with BCC-I efficiency rate 1. RTS was finalized with 8 IRS companies, 10 DRS companies, and 11 CRS companies.