• Korean Journal of Optics and Photonics
• /
• v.7 no.1
• /
• pp.66-71
• /
• 1996

We analyzed and fabricated InP/InGaAs avalanche photodiode (APD) having floating guard ring (FGR). Since the FGR-APD is very simple to fabricate and highly reliable, the fabrication of FGR-APD and its application to the optical receiver are very useful and interesting. A double zinc diffusion was employed to fabricate and one dimensional electric field analysis was used for design. Two dimensional gain measurement showed that the FGR suppressed gain at the curved edge, indicating the successful behavior as a guard ring. The fabricated device had 35 GHz of gain-bandwidth product, and showed the sensitivity of -31.9 dBm at a bit error rate of $10^{-9}$ when it was applied to a 2.5 Gbps optical receiver.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.6
• /
• pp.484-493
• /
• 2013

Typical underwater acoustic sensors can measure the scalar quantity of sound-pressure-magnitude with the limitation of being unable to identify the direction of an incoming wave. This paper proposes a method to detect the direction of the sound wave with a ring sensor. The sensor of the proposed structure has a piezoceramic ring divided into eight elements, and distinguishes the direction of the sound wave by properly combining the output voltages of the piezoceramic elements. Further, through the analysis of the effects of the structural parameters like the ring radius and length, and piezoceramic thickness, we have suggested the way to improve the sensitivity of the vector sensor.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1779-1781
• /
• 1997

The 2.0 GeV Pohang Light Source (PLS) is consisted of a full energy Linac and a storage ring. Four kicker magnets are installed in the storage ring tunnel to move the stored beam orbit in the storage ring closer to the injected beam from the beam transfer line. The injected beam then falls into the storage ring beam dynamic aperture. A kicker magnet modulator drives all four kicker magnets to maintain field balance and also synchronized kick of the beam. The kicker modulator can handle 2 GeV full energy beam. The kicker magnet modulator is installed in the storage ring tunnel and under stable operation. Specification of the kicker magnet modulator is ${\sim}6.0{\mu}s$ pulse-width, 200 ns flat-top width with ${\pm}0.2%$ regulation, ${\sim}24\;kA$ peak current, and 10 Hz repetition rate. Two thyratron switches (EEV CX-1536AX) are used in the system. In this article, design, and experimental results of the kicker magnet modulator are discussed.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1285-1293
• /
• 2018

This paper proposes a new type of consequent-pole permanent-magnet (CPPM) machine with stator axial magnetic ring that increases torque capability over a wide speed range and enhances efficiency for the built-in rare-earth permanent magnet synchronous machine used in new energy vehicles. The excitation winding of the CPPM hybrid excitation synchronous machine in the stator is replaced by ferrite magnetic ring to simplify the structure and manufacturing process of the machine. The basic structure and magnetic regulation principle of the proposed machine are introduced and compared with the traditional interior rare-earth permanent magnet synchronous machine and CPPM hybrid excitation synchronous machine. Finally, experimental results of a new type of CPPM synchronous motor prototype with axial magnetic ring are introduced in the paper.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.11 no.2
• /
• pp.34-38
• /
• 2012

In this paper, the particle swarm optimization (PSO) algorithm is adopted to design a modified ring-slot type patch rectenna with a resonance frequency of 2.45GHz. In order to accomplish minimization of dimensions and circular polarization (CP) and harmonic suppression, axial direction slits and side-cuts are added to the patch of the ring. The PSO manipulated this kind of multi-dimensional problem very well, and as a result, the designed rectenna shows a desirable performance of return loss of 21.36dB and axial ratio of 2.92dB at the frequency of 2.45GHz with compact sizing.

• Progress in Superconductivity and Cryogenics
• /
• v.13 no.1
• /
• pp.46-50
• /
• 2011

The electrical insulation design of high voltage superconducting fault current limiters (SFCLs) should be confirmed to be applied for the stabilization of the power grid. This paper describes numerical analysis and AC dielectric experiments for developing high voltage SFCLs. The electric field distributions between applied high voltage part and ground were calculated by finite element method (FEM) simulation tool and AC criterion of liquid nitrogen at 200 kPa was calculated from correlation between the field utilization factor and FEM simulation results. This paper deals with ceonceptual insulation design of a 154 kV class single-phase no-inductively wound solenoid type SFCL which was focused on gap distance between the cryostat and superconducting coils. Furthermore, the shield ring effect was confirmed to reduce maximum electric field at applied high voltage part.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.3
• /
• pp.275-283
• /
• 1991

A design method of the new 7${\lambda}$/6 ring 3dB directional coupler using fundamental /6-sections is proposed and its frequency characteristics are analyzed. Furthermore, the experimental verification has been achieved in microstrip network, and hence, the validity of the design method of a microwave compoennt with the basic ${\lambda}$/6-sections proposed in this paper is confirmed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.875-880
• /
• 2008

In this paper, we deal with the TLP evaluation results for GGNMOS in ESD protection device of conventional CMOS process. An evaluation parameter for GGNMOS is that repeatability evaluation for reference device($W/L=50\;{\mu}m1.0\;{\mu}m$) and following factors for design as gate width, number of finger, present or not for N+ gurad -ring, space of N-field region to contact and present or not for NLDD layer. The result of repeatability was showed uniformity of lower than 1 %. The result for design factor evaluation was ; 1) gate width leading to increase It2, 2) An increase o( finger number was raised current capability(It2), and 3) present of N+ gurad-ring was more effective than not them for current sink. Finally we suggest the optimized design conditions for GGNMOS in evaluated factor as ESD protection device of conventional CMOS process.

• Steel and Composite Structures
• /
• v.22 no.1
• /
• pp.183-201
• /
• 2016

Perforated steel beams can be optimised by increased beam depth and the moment of inertia combined with a reduced web thickness, favouring the use of original I-section beams. The designers are often confronted with situations where optimisation cannot be carried out effectively, taking account of the buckling risk at web posts, moment-shear transfers and local plastic deformations on the transverse holes of the openings. The purpose of this study is to suggest solutions for reducing these failure risks of tested optimal designed beams under applying loads in a self-reacting frame. The design method for the beams is the hunting search optimisation technique, and the design constraints are implemented from BS 5950 provisions. Therefore, I have aimed to explore the strengthening effects of reinforced openings with ring stiffeners, welded vertical simple plates on the web posts and horizontal plates around the openings on the ultimate load carrying capacities of optimally designed perforated steel beams. Test results have shown that compared to lateral stiffeners, ring and vertical stiffeners significantly increase the loadcarrying capacity of perforated steel beams.

• Journal of Ship and Ocean Technology
• /
• v.7 no.2
• /
• pp.40-47
• /
• 2003

LDV measurements in large cavitation tunnel around a propeller in operation are carried out to provide valuable information for more accurate wake-adapted propeller design and to study hull-propeller interactions. Effective velocities are computed by both the simplified vortex ring method and by RANS solver with the body force representing the propeller load. The former method uses the nominal velocities measured at the propeller plane as an input data of the numerical method and shows a better agreement with experimental data. The latter shows the qualitative agreement and may be used as an alternative design tools in the preliminary design stage.