• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.352-356
• /
• 2007

The Ni/Cr/Al/Cu (51/41/4/4 wt%) thin films were deposited by using DC magnetron sputtering method for the application of the resistors having low TCR (temperature coefficients of resistance) and high resistivity from the former printed-results[3]. The TCR values measured on the as-deposited thin film resistors were less than ${\pm}10\;ppm/^{\circ}C$ and $-6{\sim}+1\;ppm/^{\circ}C$ after annealing and packaging process. The TCR values were $-3{\sim}1\;ppm/^{\circ}C$ (ratio of variation : about 0.02 %) and $-30{\sim}20\;ppm/^{\circ}C$ (ratio of variation : about $0.5{\sim}1\;%$) for the thermal cycling and PCT (pressure cooker test), respectively. It was confirmed that the reliability properties of the thin film resistor were good for electronic components.

• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.95-101
• /
• 2009

A simple and new CMOS potentiostat circuit for amperometric sensor is described. To maintain a constant potential between the reference and working electrodes, only one differential difference amplifier (DDA) is needed in proposed design, while conventional potentiosatat requires at least 2 operational amplifiers and 2 resistors, or more than 3 operational amplifiers and 4 resistors for low voltage CMOS integrated potentiostat. The DDA with rail-to-rail design not only enables the full range operation to supply voltage but also provides simple potentiostat system with small hardwares and low power consumption.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2001.02a
• /
• pp.176-177
• /
• 2001

Three nearly identical superconducting fault current limiters (SFCLs) were connected in series to increase the voltage ratings. A slight difference in the quench starting point of individual SFCL units produced significantly imbalanced power distribution when connected in series. The imbalance was successfully removed by connecting a shunt resistor to one SFCL in parallel. 1.2 kV SFCL was designed with five current limiting elements and two or three shunt resistors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.7
• /
• pp.615-627
• /
• 1991

In this paper the relative magnitudes of the 1/f noise constants were experimentally investigated in the plana type's resistors fabricated with the different type's semicondector materials, and a new measurement technique for the 1/f noise in the semiconductor plana type's resistors may be located at the semiconductor and silicon dioxde.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.275-278
• /
• 2000

We were fabricated of NiCr thin film resistors(TFR) on A1$_2$O$_3$(99.5%) substrates by dc magnetic sputtering system. The characteristics of electrical resistance (Sheet resistance & Temperature-Coefficient of the resistance-value:TCR) by annealing condition and reactive gas on the resistors were studied.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.412-416
• /
• 2008

We have developed the calibration technique of the VT comparator using nonreactive standard resistors, which evaluates both accuracy and linearity of the VT comparator by comparing experimental values with theoretical values. The correction values of VT comparator obtained by using both our method and wide ratio error VT are consistent within the expanded uncertainty. Furthermore the specification for ratio error of VT comparator have been revaluated.

• Korean Journal of Materials Research
• /
• v.2 no.1
• /
• pp.58-64
• /
• 1992

TCR modifying oxides which have negative TCR were added to the $\textrm{RuO}_2$ thick film resistors and how they affect the TCR and resistivity of the systems were investigated. Two types of resistor systems whose ratio of $\textrm{RuO}_2$ to glass were 20/80 and 12/88 were used as standard resistors. It was observed that the modifiers did not always lower the TCR of the resistors and the direction of the TCR change were different from system to system. It was confirmed, however, that the feasibility of optimization of TCR of the resistors. When more than two TCR modifiers were added simultaneously there was no interaction between them. The resultant TCR of the resistor wart just sum of the effects from individual modifier. It was found to be desirable that the amount of addition of the TCR modifiers should be less than 2 to 3 percent.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.231-236
• /
• 2008

A method of moments model for the resistive vee dipole has been established. In order to validate the numerical model, an experimental model is built and reflections from the antenna in the feed line are measured. The measured data and the numerical data agree closely validating the numerical model. Based on the numerical model, efficiency of the antenna and the power dissipated in the resistors are analyzed. The results show that the antenna has low radiation efficiency because of the loading resistors and that the resistors near the drive point of the antenna dissipate more power than do the resisters far from the drive point. The results can be used to determine the amount of power that can be accepted by the resistive vee dipole, to determine the power rating of the loading resistors for a desired application, or to estimate the operation range of the antenna.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.11
• /
• pp.84-90
• /
• 1992

The dependence of electrical characteristics of RuO$_2$-based thick film resistors on the RuO$_2$ contents, glass composition variation and the firing temperatures was measured. The sheet resistance of resistors decreased as the contents of RuO$_2$ increased and at firing temperatures higher than C, the sheet resistance increased as the firing temperature increased. In case of using lead borosilicate glass-containing $Bi_{2}O_{3}$, the sheet resistance decreased as the contents of $Bi_{2}O_{3}$ increased. TCR changes from negative to positive values as RuO$_2$ contents increased and from positive to negative values as the firing temperature increased. TCR increased to positive values as $Bi_{2}O_{3}$ increased in the glass.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.3
• /
• pp.239-246
• /
• 2015

A novel control method of a three-phase PWM inverter with LC filter is proposed. The transfer function of LC filter is the same as that of second-order low pass filter(LPF), which has a zero damping ratio. A simple method of implementing second-order LPF with damping ratio is to add a resistor in an LC circuit. However, in a real power system, adopting damping resistors is impractical because it results in losses proportional to the square of the current flowing through the resistors. Instead of inserting resistors, the proposed control strategy utilizes the measured capacitor voltages to control the oscillation of LC circuit. The overall transfer function of the proposed method is the same as a second-order LPF, and its damping ratio is controllable via control variables. The current controller can have overshoots caused by LC filter. Improved current controller is implemented by an equivalent second-order of LC filter. A 7.5 kVA PWM converter and a PWM inverter with a 5.5 kW induction motor are set up to verify the proposed control algorithm. Test waveforms are also presented to verify the proposed LC filter control algorithm.