• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.245-248
• /
• 2011

The scaling down of metal oxide semiconductor field-effect transistors (MOSFETs) for the last several years has contributed to the reduction of the scaling variables and device parameters as well as the operating voltage of the MOSFET. At the same time, the variation in the electrical characteristics of MOSFETs is one of the major issues that need to be solved. Especially because the issue with variation is magnified as the drive voltage is decreased. Therefore, this paper will focus on the variations between electrical characteristics and drain voltage. In order to do this, the test patterned multi-finger MOSFETs using 90-nm process is used to investigate the characteristic variations, such as the threshold voltage, DIBL, subthreshold swing, transconductance and mobility via parasitic resistance extraction method. These characteristics can be analyzed by varying the gate width and length, and the number of fingers. Through this modeling scheme, the characteristic variations of multi-finger MOSFETs can be analyzed.

• 대한조선학회지
• /
• 제22권2호
• /
• pp.35-48
• /
• 1985

The present work develops a method of evaluating thrust deduction and wake for different loads of the propeller using the concerted application of the theoretical tools and experimental techniques. It also shows the applicability of the new method to the design of optimum hull form. Firstly, the problem of hull-propeller interaction was analyzed in terms of inviscid as well as viscous components of the thrust deduction and wake. The wavemaking resistance of a hull and propeller were mathematically represented by sources on the hull surface and sink on the propeller plane, respectively. The strength of sink was determined by utilizing the radial distributions of propeller load and nominal wake. The resistance increment due to a propeller and the axial perturbation flow induced by the hull in the propeller plane were calculated. Especially, the inviscid component of the thrust deduction was calculated by subtraction the wavemaking resistance of a bare hull, the wavemaking resistance of a free-running propeller and the augmentation of propeller resistance due to hull action from the wavemaking resistance of the hull with a propeller. The viscous components of the thrust deduction and wake were estimated as functions of propeller load which were established by the propeller load varying test after deduction the calculated inviscid components. Secondly, an analysis method of powering performance was developed based on the potential theory and the propeller load varying test. The hybrid method estimates the thrust deduction, wake and propeller open-water efficiency for different propeller load. This method can be utilized in the analysis of powering performance for the propeller load variation such as the added resistance due to hull surface roughness, the added resistance due to wind, etc. Finally, the hybrid method was applied to the optimum design of hull form. A series of afterbody shapes was obtained by systematically varying the waterplane and section shapes of a parent afterbody without changing the principal dimensions, block coefficient and prismatic coefficient. From the comparison of the predicted results such as wavemaking resistance, thrust deduction, wake and delivered power, an optimum hull form was obtained. The delivered power of the optimized hull form was reduced by 5.7% which was confirmed by model tests. Also the predicted delivered power by the hybrid method shows fairly good agreement with the test result. It is therefore considered that the new analysis method of powering performance can be utilized as a practical tool for the design of optimum hull form as for the analysis of powering performance for the propeller load variation in the preliminary design stage.

• Tribology and Lubricants
• /
• 제12권4호
• /
• pp.28-34
• /
• 1996

The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

• 동력기계공학회지
• /
• 제15권6호
• /
• pp.73-80
• /
• 2011

The experimental investigation focuses on an influence of artificial aging time in longitudinal butt welded Al 6013-T4 aluminum alloy on the fatigue crack growth resistance. The preferred welding processes for this alloy are frequently tungsten inert gas welding (TIG) process due to its comparatively easier applicability and better weldability than other gas metal arc welding. Fatigue crack growth tests were carried out on compact tension specimens (CT) in longitudinal butt TIG welded after T82 heat treatment was varied in three artificial aging times of 6 hours, 18 hours and 24 hours. Of the three artificial aging times, 24 hours of artificial aging time are offering better resistance against the growing fatigue cracks. The superior fatigue crack growth resistance preferred spatial variation of materials within each specimen in the Paris equation based on reliability theory and fatigue crack growth rate by crack length are found to be the reasons for superior fatigue resistance of 24 hours of artificial aging time was compared to other joints. The highest of crack propagation resistance occurs in artificial aging times of 24 hours due to the increase in grain size (fine grained microstructures).

• 한국인터넷방송통신학회논문지
• /
• 제9권3호
• /
• pp.173-178
• /
• 2009

금속산화물 박막 소자를 제작하여 전기적 특성을 조사하였다. 소자는 Electrode를 TOP-TOP구조로 제작하였으며 스위칭 특성을 연구하기 위해 전극간의 산화금속박막의 전도특성이 측정되었다. 소자의 저항변화는 전압을 선형적으로 인가하여 측정하였다. 제작된 소자는 MIM구조로써 외부에서 인가하는 전기적 신호에 의하여 전기전도도가 큰 On-state와 전기전도도가 낮은 Off-state로 바뀌는 특성을 나타내었다. $Si/SiO_2/MgO$ 소자는 Forming에 의해 저항이 큰 상태에서 저항이 작은 상태로 전기적 특성이 변화하면서 스위칭 특성을 보였다. 본 연구를 통하여 산화금속은 차세대 비휘발성 메모리로는 물론 다른 전기적 응용이 기대되는 물질임을 확인하게 되었다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(5)
• /
• pp.69-72
• /
• 2001

In this paper, we study about a acupuncture point and a non-acupuncture point resistance characteristics for acupuncture research. For this study, we devised resistance variation measurement system. This system is consist of 4-channel skin resistance measuring parts, filters, 12bit A/D convertor, 8051 micro-controller, and personal computer The developed system insert a low current to skin and obtains voltages from standard resistor that is convected to measurement circuit in series. The obtained voltage is converted to 12bit digital signal. Therefore the converted signal is changed to skin resistance by calculation in the personal computer. As the results of experiment, the resistance of acupuncture point and non-acupuncture point are different from each other. The acupuncture point has very fast current flows than the other non- acupuncture point.

• 설비공학논문집
• /
• 제3권4호
• /
• pp.256-262
• /
• 1991

The corrosion effects on thermal contact resistance were experimentally studied for a given contact interface of a couple of metals. 2 cylindrically shaped test pieces, the one was carbon steel whose surface was machined by lathe and the other was stainless steel, ground, were come into contact under pressure, and then submerged to $HNO_3$ gas environment. While the corrosion process was going on, the thermal contact resistance was measured with time. The experiment was performed for 2 cases; 1) Highly compress the test pieces and then bring them to $HNO_3$ gas environment. 2) Anteriorly corrode the interface under low contact pressure and then increase the contact pressure. The results were as follows; In 1st. case of experiment, the thermal contact resistance seemed to be very stable, and showed low values with a tendancy of small decrease with time. But in 2nd. case the resistance was unstable and jumped to a value of 200-250% more then that expected for uncontaminated interface. More over it demonstrated some increase with time.

• Corrosion Science and Technology
• /
• 제22권6호
• /
• pp.399-407
• /
• 2023

This study investigated the formation of oxide films on 6061 aluminum (Al) alloy and their impacts on corrosion resistance efficiency by regulating anodization voltage. Despite advantageous properties inherent to Al alloys, their susceptibility to corrosion remains a significant limitation. Thus, enhancing corrosion resistance through developing protective oxide films on alloy surfaces is paramount. The first anodization was performed for 6 h with an applied voltage of 30, 50, or 70 V on the 6061 Al alloy. The second anodization was performed for 0.5 h by applying 40 V after removing the existing oxide film. Resulting oxide film's shape and roughness were analyzed using field emission-scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). Wettability and corrosion resistance were compared before and after a self-assembled monolayer (SAM) using an FDTS (1H, 1H, 2H, 2H-Perfluorodecyltrichlorosilane) solution. As the first anodization voltage increased, the final oxide film's thickness and pore diameter also increased, resulting in higher surface roughness. Consequently, all samples exhibited superhydrophilic behavior before coating. However, contact angle after coating increased as the first anodization voltage increased. Notably, the sample anodized at 70 V with superhydrophobic characteristics after coating demonstrated the highest corrosion resistance performance.

• 한국작물학회지
• /
• 제52권2호
• /
• pp.162-168
• /
• 2007

본 연구는 벼흰잎마름병 저항성유전자 Xa1, Xa 3 및 Xa7을 가진 단인자 근동질 유전자계통에 일본의 대표균주(T7174, T7147, T7133)를 단독 및 혼합 접종하여 친화적 및 비친화적 균주의 상호작용에 따른 벼흰잎마름병 발병도에 미치는 영향을 조사하였다. Xa1 유전자를 갖는 IRBB 101 계통은 벼의 생육기간 전반에 걸쳐 T7147와 T7133 균주에는 친화적 관계로, T7174 균주에는 비친화적 관계로 작용하였다. Xa3 유전자를 갖는 IRBB 103 계통은 유묘기에서는 3 균주가 친화적 관계로 반응하였으나 출수기에 비교적 안정된 저항성을 나타냈다. Xa7 유전자를 갖는IRBB 107은 유묘기 접종에서는 3 균주가 비친화적 관계에 유사한 반응을 나타냈고, 최고분얼기 접종에서는 대부분 저항성으로 반응하였으며, 출수기에는 모두 강한 저항성으로 반응하여 비친화적 관계로 변화하였다. 친화적 균주와 비친화적 균주의 혼합접종에서는 비친화적 균주의 혼합비율이 증가할수록 병반장이 감소하는 경향 이였고, 친화적 및 비친화적 관계가 확실치 않는 경우는 병반장의 변화가 거의 없었다. 친화적 균주의 혼합접종에서는 친화적 균주의 단독 접종보다 대체로 병반장이 증가하는 경향이었으나, 비친화적 균주의 혼합접종에서는 단독 접종과 유사한 반응을 나타내어 병반장의 변화가 적었다. Xa7 유전자를 갖는 IRBB 107 계통은 벼의 생육기간동안 사용된 3 균주 모두에 저항성으로 반응하여 가장 안정된 저항성원인 것으로 판단된다.

• 한국재료학회지
• /
• 제13권1호
• /
• pp.43-47
• /
• 2003

As and BF$_2$dopants are implanted for the formation of source/drain with dose of 1${\times}$10$^{15}$ ions/$\textrm{cm}^2$∼5${\times}$10$^{15}$ ions/$\textrm{cm}^2$ then formed cobalt disilicide with Co/Ti deposition and doubly rapid thermal annealing. Appropriate ion implantation and cobalt salicide process are employed to meet the sub-0.13 $\mu\textrm{m}$ CMOS devices. We investigated the process results of sheet resistance, dopant redistribution, and surface-interface microstructure with a four-point probe, a secondary ion mass spectroscope(SIMS), a scanning probe microscope (SPM), and a cross sectional transmission electron microscope(TEM), respectively. Sheet resistance increased to 8%∼12% as dose increased in $CoSi_2$$n^{＋}$ and $CoSi_2$$p^{V}$ , while sheet resistance uniformity showed very little variation. SIMS depth profiling revealed that the diffusion of As and B was enhanced as dose increased in $CoSi_2$$n^{＋}$ and $CoSi_2$$p^{＋}$ . The surface roughness of root mean square(RMS) values measured by a SPM decreased as dose increased in $CoSi_2$$n^{＋}$ , while little variation was observed in $CoSi_2$$p^{＋}$ . Cross sectional TEM images showed that the spikes of 30 nm∼50 nm-depth were formed at the interfaces of $CoSi_2$$n^{＋}$ / and $CoSi_2$/$p^{＋}$, which indicate the possible leakage current source. Our result implied that Co/Ti cobalt salicide was compatible with high dose sub-0.13$\mu\textrm{m}$ process.