• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.81-82
• /
• 2019

In this study, the Proctor penetration resistance test value and the hardness value of the improved Durometer were compared and analyzed for the change in the FA replacement rate of the concrete using CGS fine aggregate. The results are summarized as follows. It is. 1) The Proctor penetration resistance test value and the hardness value of the improved Durometer showed a high correlation in the form of a curve. 2) About surface finish Super-resolution with the improved Durometer is considered to be useful when using about 50 HD and about 80 HD in the end to determine the surface finishing work time.

• 한국어병학회지
• /
• 제24권2호
• /
• pp.95-102
• /
• 2011

Normalized resistance interpretation (NRI) analysis for tetracycline was applied to generate information on the epidemiological cut-off value for Vibrio ichthyoenteri isolated from diseased olive flounder (Paralichthys olivaceus) larvae. Thus, 42 strains of V. ichthyoenteri were used to determine minimum inhibitory concentration (MIC) values of tetracycline using Etest. Also, 11 tetracycline resistance related genes were investigated by PCR method. Most tetracycline-resistant strains harbored both tetB and tetM with a few exceptions. NRI-derived mean and 2 SD above the mean of theoretical normal distributions of susceptible isolates were 0.33 mg/L and 1.66 mg/L, respectively. The epidemiological cut-off value for V. ichthyoenteri from the calculations could be set to S ${\leq}$ 2 mg/L. Of the 42 strains, 15 were classified as non-wild type (NWT), and MIC values of the NWT strains vary regardless of tetB and tetM detection, suggesting that there may be other mechanisms involved in tetracycline resistance in this Vibrio species.

• Elastomers and Composites
• /
• 제43권2호
• /
• pp.104-112
• /
• 2008

통상적인 고무블렌드 방법에 따라 개방식 2-롤밀을 사용하여 ethylene propylene diene terpolymer (EPDM)과 styrene butadiene rubber (SBR) 블렌드 배합물을 제조하여, 이들의 경화 특성, 기계적 성질 및 내오존성 등을 검토하였다. SBR함량이 증가할수록 가황곡선의 토크가 증가하였다. 최대 토크는 SBR 25wt% 일 때 가장 낮았으며 그 이상의 SBR 량에서는 직선적으로 증가하였다. 스코치시간 및 최적경화시간은 SBR고무 함량이 증가함에 따라 감소하였다. 경도는 SBR 함량이 50wt% 일 때 최고값을 보였으며 그 전후에서는 감소하는 경향을 보였다. 내오존시험에 있어서 소량의 EPDM 고무의 첨가에 의하여 내오존성이 크게 개선됨을 확인할 수 있었다.

• 수산해양기술연구
• /
• 제47권4호
• /
• pp.281-289
• /
• 2011

The purpose of this study is to identify the flow resistance of the bottom trawl net. The bottom trawl net being used in the training ship of Chonnam National University was selected as a full-scale net, and model nets such as 1/10, 1/25 and 1/50 of the actual net were made. Total resistance of the net part, the height of the net mouth and the flow resistance of components of the net such as wing, bag and cod-end part was measured, converted into full-scale and compared. Additionally, the model rule of Tauti (1934), which has been most frequently used in fishing net modeling experiments, was applied to interpret flow resistance and scale effect of model experiment was investigated. Presumed that the flow resistance R is $R=kS{\upsilon}^2$ against the flow velocity of each net ${\upsilon}$, resistance coefficient k was calculated by substituting R, ${\upsilon}$ and S of the net. From the result, it was found that k decreases exponentially when u increases which makes $k=c{\upsilon}^{-m}$. Whereas m of each net is ranged between 0.13-0.16 and there was not significant difference between nets. c does not show big difference in 1/10 and 1/25 model and the value itself was relatively bigger than in 1/50 model. The height of the net mouth of 1/25 and 1/50 model net h decreases exponentially according as ${\upsilon}$ increases to make $h=d{\upsilon}^{-n}$. Whereas d and n values were almost same in two nets. Additionally, when resistance of cod-end, wing and bag part in 1/25 and 1/50 model nets, both nets showed big resistance in bag part when flow is 1m/s as more than 60%. Wing and cod-end part showed almost same value or wing part had little bit larger value. On the other hand, when reviewing the reasons why both models showed difference in 1/50 model while c value against the resistance coefficient k did not show big difference in 1/10 and 1/25 model, it is inferred that the difference occurred not from material difference but from the difference in net size according to scale. It was judged that they are the scale effects concomitant to the model experiments.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제8권4호
• /
• pp.155-166
• /
• 2008

PTH cracks are caused by the mismatch of coefficient of thermal expansion(CTE) between polymer and laminated materials, and are one of the main failure mechanisms of multi layer boards. In spite of its importance, it is usually hard to measure or detect them because of its small size and invisibility. To detect PTH cracks more effectively, this paper proposes a theoretical model that can estimate the resistance value from crack size of PTHs. Using four-point probe resistance measurement method, the resistance value of test coupons is measured. Through measured data, we verify the validity of the proposed theoretical model and set up criteria of failure.

• Journal of Forest and Environmental Science
• /
• 제18권1호
• /
• pp.45-52
• /
• 2001

본 논문은 솔잎혹파리 피해임지에서 수목의 외형적인자(수고, 수관폭, 흉고직경, 지하고)와 shigometer를 이용한 전기 저항치 ($k{\Omega}$)의 관계를 조사하였다. 외형적인자와 저항치간의 관계는 수고, 수관폭, 흉고직경은 높은 상관관계가 있었고, 지하고는 뚜렷한 관계가 나타나지 않았다. 수고, 수관폭, 흉고직경은 큰 수목이 전기저항치가 낮았고(수목의 활력이 높음) 작은 수목이 전기저항치가 높았다(수목의 활력이 낮음). 솔잎혹파리 피해임지의 고사목과 생존목을 비교하면 고사목이 생존목에 비하여 수관폭과 흉고직경의 크기는 작았고, 지하고는 높았다. 전기저항치를 3등급으로 구분 한 결과(< $14{\Omega}$, 생존가능성 양호, $14{\sim}20{\Omega}$, > $20k{\Omega}$고사 가능성 있음), 외형적인자의 크기는 낮은등급(< $14{\Omega}$)에서 수고, 수관폭, 흉고직경이 컸으며, 지하고는 낮았다. 조사한 외형적인자와 수세와의 관계를 직선회귀 방정식으로 산출한 결과 Y=-0.572${\times}$수고-1.163${\times}$수관폭-0.242${\times}$흉고직경+0.757${\times}$지하고+25.765이였으며 이들의 회귀식은 5%의 수준에서 유의성이 인정된다.

• 한국의류학회지
• /
• 제39권1호
• /
• pp.121-132
• /
• 2015

All aspects of clothing, including color, are a visible form of expression that carries invisible value. The purpose of this work is to study the expression of resistance in the white Hanbok in modern culture, specifically after the 1980s. Koreans have traditionally revered white color and enjoyed wearing white clothes. In Korea, white represents simplicity, asceticism, sadness, resistance against corruption, and the pursuit of innocence. This paper looks at: (i) the universal and traditional values of the color white, (ii) the significance of traditional white Korean clothing, (iii) the resistance characteristics of white in traditional Korean clothes, and (iv) the aesthetic values of white Hanbok. The white Hanbok often connotes resistance when it is worn in modern Korea. It is worn in folk plays, worn by shamans as a shamanist costume, worn by protestors for anti-establishment movements, and worn by social activists or progressive politicians. The fact that the white Hanbok has lost its position as an everyday dress in South Korea (instead symbolizing resistance when it is worn) is an unusual phenomenon. It shows that the white Hanbok, as a type of costume, is being used as a strong means of expression, following a change in the value of traditional costumes as it take on an expressive function.

• 한국기계가공학회지
• /
• 제21권8호
• /
• pp.99-109
• /
• 2022

In this study, an electric resistance-heated surface friction spot-welding process was proposed and tested for the spot-welding ability of copper and aluminum dissimilar metal sheets using electric resistance heating and surface friction heating. This process has welding variables, such as the current value, energizing cycles, rotational speed, and friction time. The current value and energizing cycle can affect the resistance heat, and the rotational speed of the rotating pin and friction time influence frictional heat generation. Resistance heating before friction heating has a preheating effect on the Cu-Al contact interface and a positive effect on preventing friction heat loss during the friction stage. However, because resistance preheating can soften the copper sheet and affect the contact stress and friction coefficient, it has difficulties that may adversely affect frictional heat generation. Therefore, the optimal combination of welding variables should be determined through simulations and experiments of the spot-welding process to determine the effects of electric resistance preheating on the suggested process. Through this procedure, it is known that the proposed spot-welding process can improve the welding quality during the spot welding of Cu-Al sheets.

• 한국환경보건학회지
• /
• 제21권2호
• /
• pp.7-11
• /
• 1995

This study was carried out to investigate the change of average specific resistance according to filtration pressure, suspension concentration and filters for study phenomena occurring in cake filtration. As the results of this study, the following conclusions were obtained. It was estimated that the average specific resistance of filtration Was decreased in proportion to decreased of filtration pressure. But in very pressure, average specific resistance was increased. The average specific resistance value on filter medium by various pressure was showed as same trends under constant suspension concentration. This phenomenon was though that a carrain amount of fine particles in the cake was found to migrate throught the cake in the case of very thin at very low pressure. In relation to the change of suspension concentration, average specific resistance value become low according to decreased in supension concentration.

• 상하수도학회지
• /
• 제22권3호
• /
• pp.281-288
• /
• 2008

Cake resistance is influenced by floc size deposited on membrane surface. Enlarging floc size can reduce cake resistance. The small particles are enlarged by coagulation and flocculation process in conventional mixing tank at membrane filtration system. Fully-grown flocs for reducing the cake resistance, however, are ruptured while passing through a pump. In light of this fact, this study aims to experimentally look at the reaggregation phenomenon of mixing system. In addition, reaggregation phenomenon of mixing system is compared with first-aggregation of in-line injection system in which coagulant is injected just before a pump. These results suggest that first-aggregation of in-line injection system is better than reaggregation of mixing system for G-value above $3100sec^{-1}$. Since G-value in pipe of actual membrane filtration system are usually larger than $3100sec^{-1}$. The performance of in-line injection system is expected to be better than the conventional mixing tank system.