• Structural Engineering and Mechanics
• /
• 제47권6호
• /
• pp.819-838
• /
• 2013

This paper summarises the results of an experimental study to investigate the flexural behaviour of reinforced concrete beams strengthened using carbon-fibre reinforced polymer (CFRP) laminate in four-point bending. The experimental parameters included are the reinforcing bar ratio ${\rho}_s$ and preload level. Four bar ratios were selected (${\rho}_s=0.13$ to 0.86%), representing the section of two longitudinal tensile reinforcements, with diameters of 8, 14, 16, and 20 mm in order to reveal the effect of bar ratio on failure load and failure mode. Eight beams that could be considered "full-scale" in size, measuring 200 mm in width, 400 mm in total height and 2300 mm in length, were tested. Three beams were selected with different bar ratios (${\rho}_1$, ${\rho}_2$, ${\rho}_3$), and considered as control specimens (without ), while three other beams identical to the control beams with the same CFRP laminates ratio and a seventh beam with ${\rho}_{min}$ (the lowest bar ratio) were also used. In the second part of the study, two beams with the bar ratio ${\rho}_2$ were preloaded at two levels, 50 and 100% of their ultimate loads, and then repaired. This experimental investigation was consolidated using an analytical model. The experimental and analytical results indicate that the flexional capacity and stiffness of strengthened and repaired beams using CFRP laminate were increased compared to those of control beams, and the behaviour of repaired beams was nearly similar to the undamaged and strengthened beams; unlike the ductility of strengthened beams, which was greatly reduced compared to the control.

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.42-50
• /
• 2020

This study explores the effects of repair width on the deposition characteristics and mechanical properties of stainless steel samples repaired using direct energy deposition (DED). In the DED repair process, defects such as pores and cracks can occur at the interface between the substrate and deposited material. In this study, we changed the width of the pre-machined zone for repair in order to prevent cracks from occurring at the inclined surface. As a result of the experiment, cracks of 10-40 ㎛ in length were formed along the inclined slope regardless of the repair width. Yield and tensile strength decreased slightly as the repair width increased, but the total and uniform elongation increased. This is due to the orientation of the crack. For specimens with a repair width of 20 mm, yield and tensile strength were 883 MPa and 1135 MPa, respectively. Total and uniform elongations were 14.3% and 8.2%, respectively. During observation of the fracture specimens, we noted that the fracture of the specimen with an 8 mm repair width occurred along the slope, whereas specimens with 14 mm and 20 mm repair depths fractured at the middle of the repaired region. In conclusion, we found that tensile properties were dependent upon the repair width and the inclination of the crack occurred at the interface.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.617-620
• /
• 2008

구조물의 열화부위를 제거하고 단면수복재로 되메우는 단면수복공법의 합리적인 시공을 위해서는 외부로부터 침투되는 염화물이온에 대한 단면수복재 및 이를 시공한 철근콘크리트구조물의 염화물이온 침투예측의 선행이 필요하다. 따라서 본 연구에서는 단면수복재 시공이후의 구조물의 염해상태를 예측하고, 염화물이온의 침투 및 그에 의한 철근부식을 예측하기위해 단면수복재를 시공한 콘크리트의 염화물이온 확산계수를 정확히 파악하고자 한다. 본 연구에서는 실제 염화물이온 급속침투실험(Rapid Chloride Permeability Test)를 통한 단면수복재의 염화물이온 확산계수를 실험적으로 산정하고 단면수복재의 두께가 염화물이온 확산에 미치는 영향 또한 수치적으로 규명하였다. 실험에서 도출된 콘크리트 및 단면수복재의 염화물이온 확산계수를 일본토목학회에서 제시한 식 및 유한요소해석(Finite Element Method)를 이용하여 단면수복재로 보수시공한 구조물의 위치별 염화물이온농도를 산출하였다.

• Advances in aircraft and spacecraft science
• /
• 제4권6호
• /
• pp.679-699
• /
• 2017

The aim of this study is to perform a finite element analysis of the Von Mises stresses distribution in the adhesive layer and of the J-Integral for a damaged plate repaired by a composite patch. Firstly, we study the effect of the fiber orientation, especially the position of the layers that have orientation angle different of $0^{\circ}$ from the first layer which is in all cases of our study oriented at ($0^{\circ}$) on the J-Integral. Secondly, we evaluate the effects of the mechanical properties of the patch and the use of a hybrid patch on the reduction of stresses distribution and J-Integral. The results show clearly that the stacking sequence for the composite patch must be selected to absorb optimally the stresses from the damaged area and to position the various layers of the composite under the first layer whose fibers orientation will remain in all cases equal to $0^{\circ}$. The use of a hybrid composite reduces significantly the J-Integral and the stresses in both damaged plate and the adhesive layer.

• Archives of Plastic Surgery
• /
• 제37권2호
• /
• pp.175-177
• /
• 2010

Ppupose: Velopharyngeal insufficiency (VPI) during articulation development period can cause compensatory articulation like glottal stop, which can maintain VPI symptoms such as hypernasality and nasal emission despite of recovered velopharyngeal function. Methods: A girl visited our department with speech problems such as hypernasality, compensatory articulation patterns, and nasal air emission. She had history of postpalatoplasty fistula which was repaired after 1 year follow-up. Results: After treated with speech therapy without surgery, her hypernasal speech problem was corrected. From this, we could assume that the fistula during articulation development period induced VPI, which leads to glottal substitution and this compensatory articulation maintained VPI though the fistula was repaired. Conclusion: In this report, we could observe that palatal fistula in articulation development period can have detrimental effect on articulation, and also we could confirm that evaluation of soft palate mechanism with using speech sample without compensatory articulations prevent the patient from unnecessary operation.

• Journal of Chest Surgery
• /
• 제17권4호
• /
• pp.729-734
• /
• 1984

Bochdalek hernia is a type of congenital diaphragmatic defect in the posterolateral portion of the diaphragm. The defect is usually Lt. sided due to protective effect of liver on right. Sex distribution is male preponderance [2:1] and it is diagnosed during neonate, mostly first 24 hours, due to severe respiratory distress. We experienced a rare case of old aged female patient with congenital Bochdalek hernia on Rt. side which was found incidentally during treatment of spontaneous pneumothorax of Rt. side. 17 year old female patient was admitted to CS department for chest discomfort on right and mild dyspnea with duration of 20 days. Under the diagnosis of spontaneous pneumothorax, Rt. closed thoracostomy and underwater sealed drainage with continuous suction was applied. On follow-up chest x-ray, poorly defined hazy increased density with multiple air-fluid levels in Rt. lower lung field and Lt. subphrenic free air were noted. So, Barium enema was done under the impression of Rt. diaphragmatic hernia, and nearly entire colon proximal to sigmoid was demonstrated in the Rt. hemithorax. Operation was done-for surgical repair of defected diaphragm through Rt. posterolateral thoracotomy. Operative findings were as follows; 1.Hypoplastic Rt. lung, esp. RML & RLL. 2.Nearly entirely intestines were herniated. 3.Diaphragmatic defect was located on posterolateral portion of the diaphragm, about 10x3cm in size with blunt smooth margin. 4.A large bleb on apex of RUL of lung. Herniated intestines were repaired into abdominal cavity manually and defect of diaphragm was repaired with No. I black silk interrupted sutures directly, and bleb was resected. Postoperative courses were uneventful and the patient was discharged with good condition on POD 14th.

• Structural Engineering and Mechanics
• /
• 제82권1호
• /
• pp.17-30
• /
• 2022

The use of composite patches for the reduction of stresses at the level of the damaged zone in aeronautical structures has experienced rapid expansion given its advantages over conventional mechanical processes (riveting, bolting, etc.). Initially, The research axes in this field were aimed at choosing suitable mechanical properties for the composite and the adhesive, then to optimize the shape of the composite patch in order to ensure good load transfer and avoid having a debonding at the level of the edges essentially for the case of a repair by single side where the bending moment is present due to the non-symmetry of the structure. Our work falls within this context; the objective is to analyze by the finite element method the fracture behavior of a damaged plate repaired by composite patch. Stress reduction at the edge is accomplished by creating a variable angle chamfer on the composite patch. The effects of the crack length, the laminate sequence and the nature of the patch as well as the use of a hybrid patch were investigated. The results show clearly that a beveled patch reduces the stress concentrations in the damaged area and even at its edges. The hybrid patch also ensures good durability of the repair by optimizing its stacking sequence and the location of the different layers according to the fibers orientations.

• Composites Research
• /
• 제29권3호
• /
• pp.117-124
• /
• 2016

본 연구에서는 스카프 패치로 수리한 복합재 단일겹침 체결부의 파손강도를 시험과 해석으로 연구하였다. 스카프 비, 모재의 적층패턴, 결함크기를 달리 하며 총 45개의 시편에 대한 시험을 수행하여 파손강도와 파손모드를 분석하였다. 다양한 형상의 시편에 대한 시험 결과, 한 경우를 제외하고는 수리 후의 체결부가 결함이 없는 체결부 강도 이상의 강도를 회복하며, 체결부 인자에 따른 특별한 차이는 나타나지 않는 것을 확인하였다. 파손강도가 낮게 나타난 한 경우에 대한 파손면 분석결과 모재의 표면층인 평직층의 표면처리가 충분치 않은 것이 원인인 것으로 판단되었다. 시험 결과의 분석을 위해 3차원 유한요소해석을 수행하였는데, 유한요소해석에서도 고려한 체결부 인자가 상하부 모재와 패치, 접착층에서의 응력에 큰 영향을 미치지 않는 것을 확인하였다. 이는 단일겹침 체결부의 경우 외부 인장하중이 겹침영역을 통과하면서 상하부 모재로 분산되기 때문인 것으로 판단된다. 시험과 해석 결과 모재 중앙에 결함이 존재하는 단일겹침 체결부의 경우 절차에 따라 패치 접착이 이루어지고, 모재의 표면처리가 충분히 이루어진다면 수리를 통해 손상 전 강도를 회복할 수 있는 것으로 판단된다.

• 한국재난정보학회 논문집
• /
• 제19권1호
• /
• pp.138-145
• /
• 2023

연구목적: 건축물의 노후화에 따른 보수, 보강 건축물의 증가에 따라 기 보강된 건축물에 화재가 발생시 화재 후 구조물에 미치는 영향성을 분석하여 보수, 보강대책의 기준을 마련하고자 한다. 연구방법: 콘크리트 배합설계에 의한 공시체를 제작하여 28일 양생 후 압축기를 통해 압축강도 측정 및 파괴를 유도후 에폭시로 보수, 보강하여 3일 양생 후 일부공시체를 재 압축강도시험을 실시하여 강도 복원 정도를 파악하고 보수, 보강한 나머지와 보수, 보강하지 않은 공시체를 실험용 전기로에 넣고 시간, 온도별로 가열한 후 압축강도를 실험하여 화재의 영향성을 추정함. 연구결과: 항복된 공시체를 에폭시로 보강한 후 실험용전기로에 넣어 가열을 시간별로 온도의 차이를 주어 실험한 결과 높은 온도에서 열 영향을 받는 시간이 길면 길수록 강도의 저하가 발생함을 알 수 있었고 보수, 보강되지 않은 공시체보다 더 강도 저하가 있음을 알 수 있었다. 결론: 이를 토대로 볼 때 에폭시 수지로 보수, 보강된 건축물이 화해를 입을 때는 일반 보수되지 않은 건축물보다 더 위험함을 알 수 있었으므로 화재에 대한 안정성을 고려하였을 때 보수보강 표면에 내화피복재 등을 도포하는 등 화재 취약에 대비하여야하겠다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.739-744
• /
• 2000

The aim of this research is to investigate and to compare the shear strengthening effects of steel plates and glass fiber sheets(GFS). Shear damaged beams were repaired by steel plates and GFS. Thickness of steel plates and strengthening type of GFS were taken as the parameters. With loading, the development and propagation of cracks, failure mode and deformation of strengthening materials were checked. The ultimate load was compared with formulas proposed by previous researchers.