• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.221-224
• /
• 2004

This paper has researched on-chip spiral inductor in digital CMOS technology by modeling physical structure based on foundry parameter. To show the possibility of its application to RF design, we designed dual band RF front-end receiver. The simulated receiver have gain of 23/23.5 dB and noise figure of 2.8/3.36 dB at 2.45/5.25 GHz, respectively. It occupies $16mm^2$ in $0.25{\mu}m$ CMOS with 5 metal layer.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.333-339
• /
• 1994

We fabricated a single mode fiber pigtailed PIN-preamplifier front-end receiver module for the high speed optical receiver. Hybrid method was used to integrate GaInAs PIN photodiode and transimpedance type GaAs preamplifier. The capacitance and the diameter of light receiving area of PIN photodiode were 0.35 pF and $20{\mu}m$ respectively. The -3 dB cut-off frequency of PIN-preamplifier module was above 2 GHz, and the sensitivity of the module at 2.5 Gbps NRZ $(PRBS=2^{23}-1)$ signal was -25.2 dBm at $10^{-9}$ BER. > BER.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.703-705
• /
• 2016

In this paper, we developed a wideband PIMD system to measure passive intermodulation distortion signals of mobile communication RF passive module. To represent wideband characteristic, we designed a receiver that meets low-noise and wideband characteristics in RF receiver. It allows high dynamic range in the RF receiver front end. In designed passive intermodulation distortion measurement system, we programed to display a PIMD signal with FPGA/DSP at PC. Implemented PIMD system was variable from 650 MHz to 2700 MHz and show up to -138 dB minimum detectable $3^{rd}$ passive inetrmodulation distortion signal.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5A
• /
• pp.490-496
• /
• 2007

This paper describes the design and implementation of an integrated LTCC front-end module for the IEEE802.11a WLAN applications by performing the behavioral-level simulation using measurement-based behavioral model. To meet the IEEE802.11a WLAN standard, a system transmitting 1024 symbols through 64-QAM process at the rate of 54Mbps should be implemented and nonlinear properties are confirmed by simulations of ACPR and EVM in this circumstance. The right offsets of ACPR which are 30MHz, 20MHz, and 11MHz distant from the center frequency of 5.8GHz are 49.36dBc, 36.90dBc, and 24.58dBc, respectively. The left offsets are 50.14dBc, 30.04dBc, and 28.85dBc, respectively and EVM is 2.94%. The size of the module implemented with LTCC five-layer substrates is $13.4mm{\times}14.2mm$. The measured characteristics of the transmitter show P1dB of 16.2dBm and power gain of 16.73dB. Those of the receiver exhibit the small signal gain of 16.24dB and noise figure of 7.83dB.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.3
• /
• pp.15-20
• /
• 2012

This paper presents a 5-Gb/s optical receiver circuit realized in a $0.13-{\mu}m$ CMOS technologies for the applications of high-speed digital interface. Exploiting modified RGC input stage at the front-end transimpedance amplifier, interleaving active feedback and source degeneration techniques at the limiting amplifier, the proposed optical receiver chip demonstrates the measured results of $72-dB{\Omega}$ transimpedance gain, 4.7-GHz bandwidth, and $400-mV_{pp}$differential output voltage swings up to the data rate of 5-Gb/s. Also, the chip dissipates 66mW in total from a single 1.2-V supply, and occupies the area of $1.6{\times}0.8mm^2$.

• International journal of advanced smart convergence
• /
• v.7 no.4
• /
• pp.50-56
• /
• 2018

The Internet of Things (IoT) and Visible Light Communication (VLC) is opening up new services in lighting industry by integrating sensory network features in addition to standard illumination functionality. In this progressive developments, the next generation lighting devices for smart homes are capable to sense the environmental conditions and transfer the captured data through lights to gateway controller to access remotely. The smart home environmental sensor information's are few kbps only so VLC systems need to built-in with low rate light connectivity to transfer data to the gateway. To provide error free communication, the quality of a received light signal is important to be considered when designing an VLC receiver. Therefore, this paper proposes the design of robust low rate IoL receiver design using NCP302 voltage detector for micro controller to adapt the IoT/IoL front end module for system integration. To evaluate the proposed system performance, the Arduino UNO based IoT/IoL controller designed with lighting, sensors and lights connectivity interfaces. The experimental result shows that the robust interference rejection is feasible on proposed VOL receiver and possible to have an error-free communication up to 10 kbps at a low SNR using OOK modulation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.7
• /
• pp.1534-1540
• /
• 2005

The direct conversion method is classified into the structure using the mixing technology and six-port scheme. In the view point of complexity and integration the direct conversion method using the six-port scheme is superior to that with mixing technology. Expecially, the six-port direct conversion technology provides the low power consumption and the broad-band characteristic. In this paper, the six-port direct conversion receiver with the branch-line coupler and the ring hybrid coupler is desisted respectively. The performances of the designed six-port schemes are analyzed and the six-port scheme with superior performance characteristics is proposed.

• Journal of IKEEE
• /
• v.2 no.2 s.3
• /
• pp.173-177
• /
• 1998

Under indoor environment, in case that wireless optical LAN does not obtain the line-of-sight between transmitter and receiver, hemi-spherical lens or reflector must be adopted to get broader beam width. The beam tilt and the fluctuations in amplitude and phase of optical signal through indoor-space occur due to the turbulene. This fading often results in unacceptably large bit error probabilities and thus performance degradation of wireless optical communications. In this paper, when the spherical filter at the front-end of transmitter and receiver is used for wireless optical channel not satisfying line-of-sight, the signal-to-noise ratio as to zenithal angle and the effect from the turbulence due to indoor temperature are investigated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.4
• /
• pp.277-284
• /
• 1988

A 12GHz low-noise amplifier, a single gate GaAs MESFET mixer, and a low-pass filter have been fabricated for DBS receiver applications by using MIC technology. Each subsystem contains DC block with symmetric line and ship capacitor, respectively. The frequency converter with chip capacitor exhibits a 20-23 dB conversin gain with a RF bandwidth of 11.581-11.981 GHz and an IF bandwidth of 581-981MHz. Rf bandwidth of 12.1GHz and an IF banewidth of 1GHz.

• ETRI Journal
• /
• v.34 no.2
• /
• pp.216-225
• /
• 2012

This paper presents a transceiver module for human body communications whereby a spread signal with a group of 64 Walsh codes is directly transferred through a human body at a chip rate of 32 Mcps. Frequency selective digital transmission moves the signal spectrum over 5 MHz without continuous frequency modulation and increases the immunity to induced interference by the processing gain. A simple receiver structure with no additional analog circuitry for the transmitter has been developed and has a sensitivity of 250 ${\mu}V_{pp}$. The high sensitivity of the receiver makes it possible to communicate between mobile devices using a human body as the transmission medium. It enables half-duplex communication of 2 Mbps within an operating range of up to 170 cm between the ultra-mobile PCs held between fingertips of each hand with a packet error rate of lower than $10^{-6}$. The transceiver module consumes 59 mA with a 3.3 V power supply.