• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.6
• /
• pp.647-653
• /
• 1988

A rapid thermal annealing system using tungsten halogen lamp has been designed and assembled. A control scheme where the temperature control is executed with calculated wafer temperature by considering the thermocouple delay rather than measured thermocouple temperature,is proposed. This control scheme gives more accurate control of the wafer temperature. In addition, the distribution of transmitted light power to the wafer in the system has been simulated, and lamp interval modification has been able to give more uniform light power distribution. Considering incident light spectrum, absorption, reflection, radiation of silicon, etc., temperature profile has been simulated. When the light power uniformity on the 3" wafer is below 1%, the temperature uniformity is about 2%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.288-291
• /
• 2002

Application of metal silicides such as TiSi$_2$ and CoSi$_2$ as contacts and gate electrodes are being studied. However, TiSi$_2$ due to the linewidth-dependance, and CoSi$_2$ due to the excessive Si consumption during silicidation cannot be applied to the deep-submicron MOSFET device. NiSi shows no such problems and can be formed at the low temperature. But, NiSi shows thermal instability. In this investigation, NiSi was formed with a Ti-capping layer to improve the thermal stability. Ni and Ti films were deposited by the thermal evaporator. The samples were then annealed in the N$_2$ ambient at 300-800$^{\circ}C$ in a RTA (rapid thermal annealing) system. Four point probe, FESEM, and AES were used to study the thermal properties of Ti-capped NiSi layers. The Ti-capped NiSi was stable up to 700$^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after 600$^{\circ}C$. The AES results revealed that the Ni diffusion further into the Si substrate was retarded by the capping layer, resulting in the suppression of agglomeration of NiSi films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.151-154
• /
• 1998

We have investigated a correlation of the electrical properties of the Pd/Ge/Pd/Ti/Au ohmic contact on n-InGaAs with its microstructures for the high temperature application of compound semiconductor devices. The samples were heat-treated by the rapid thermal annealing at various temperatures. In the contact system, moderately good specific contact resistance was obtained even before annealing because of the low metals-InGaAs barrier height, and better ohmic performances were observed by annealing up to 400˚C. But the ohmic performance was degraded after annealing at 450˚C due to the increment of Pd$_2$Ga$\sub$5/ phases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.227-227
• /
• 2008

CdS is II-VI semiconductor with a wide band gap of approximately 2.42 eV. CdS is the most popularly employed heterojunction partner to p-CdTe due to its similar chemical properties. The as-deposited films are annealed in Rapid Thermal Annealing (RTA) system in various atmosphere(Air, Vacuum and $N_2$) at $500^{\circ}C$. In this work, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of chemical bath deposited (CBD) CdS films on glass is carried out. In case of the annealed CdS films in $N_2$, grain size was larger than as-annealed films.

• Korean Journal of Materials Research
• /
• v.13 no.7
• /
• pp.460-464
• /
• 2003

Ni and Ti films were deposited by the thermal evaporator, and then annealed in the N$_2$ ambient at 300-80$0^{\circ}C$ in a RTA(rapid thermal annealing) system. Four point probe, AEM, FESEM, AES, and XPS were used to study the effects of Ti-capping layers on the thermal stability of NiSi thin films. The Ti-capped NiSi was stable up to $700^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after $600^{\circ}C$. These results were due to that the Ni in-diffusion and Si out-diffusion were retarded by the capping layer, resulting in the suppression of the formation of NiSi$_2$and Si grains at the surface.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.8
• /
• pp.325-329
• /
• 2003

Effects of thermal treatment on the structural properties of diamond-like carbon (DU) films were examined. The DLC films were deposited by using a modified filtered cathodic vacuum arc (FCVA) deposition system and by varying the negative substrate bias voltage, deposition time, and nitrogen flow rate. Thermal treatment on DLC films was performed using a rapid thermal annealing (RTA) process at $600^{\circ}C$ for 2min. Raman spectroscopy, x-ray photoemission spectroscopy (XPS), atomic force microscope (AFM), and surface profiler were used to characterize the I$_{D}$I$_{G}$ intensity ratio, sp$^3$ hybrid carbon fraction, internal stress, and surface roughness. It was found for all the deposited DLC films that the RTA-treatment results in the release of internal compressive stress, while at the same time it leds to the decrease of sp$^3$ fraction and the increase of I$_{D}$I$_{G}$ intensity ratio. It was also suggested that the thermal treatment effect on the structural property of DLC films strongly depends on the diamond-like nature (i.e., sp$^3$ fraction) of as-deposited film.ed film.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.335-340
• /
• 2000

We investigated the role of the capping layers in the formation of the cobalt silicide in Co/Si systems with TiN and Ti capping layers and without capping layers. The Co/Si interfacial reactions and the phase transformations by the rapid thermal annealing (RTA) processes were observed by sheet resistance measurements, XRD, SIMS and TEM analyses for the clean silicon substrate as well as for the chemically oxidized silicon substrate by $H_2SO_4$. We observed the retardation of the cobalt disilicide formation in the Co/Si system with Ti capping layers. In the case of Co/$SiO_2$/Si system, cobalt silicide was formed by the Co/Si reaction due to with the dissociation of the oxide layer by the Ti capping layers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.139-142
• /
• 2002

Characteristics of piezoelectric thick films prepared by screen printing were investigated. The piezoelectric thick films were fabricated using Pb(Al,Nb)O$_3$-Pb(Zr,Ti)O$_3$ system on Si-substrate. The fabricated thick films were burned out at 400$^{\circ}C$ and sintered at 850∼1000$^{\circ}C$ using rapid thermal annealing(RTA) precess. The thickness of piezoelectric thick films were 10$\mu\textrm{m}$. PAN-PZT thick film on Ag-Pd/SiO$_2$/Si prepared at 900$^{\circ}C$/1300sec had remanent polarization of 19.70 ${\mu}$C/$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.429-432
• /
• 1999

The growth of $\textrm{YMnO}_3$ films directly on Si(100) substrates by RF magnetron sputtering system has been performed. The structural properties of $\textrm{YMnO}_3$ films on Si(100) by rapid thermal annealing(RTA) analysed by XRD(X-ray diffraction). The c-axis oriented $\textrm{YMnO}_3$ peaks were observed deposited in $\textrm{YMnO}_3$/Si(100) structure at RF power of 100W and at a temperature range of $840^{\circ}C$~$870^{\circ}C$ in oxygen ambient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.21-24
• /
• 1997

Ferroeletric LiNbO$_3$ thin films hale been prepared directly on Si(100) substrates by conventional RF magnetron spurttering system for nonvolatile memory applications. As-deposited films were performed RTA(Rapid Thermal Annealing) treatment in an oxygen atmosphere at 600 $^{\circ}C$ for 60 s. The rapid thermal annealed films were changed to poly-crystalline ferroelectric nature from amorphous of as-deposition. The resistivity of the ferroelectric LiNbO$_3$ film was increased from a typical vague of 1~2$\times$10$^{8}$ $\Omega$.cm before the annealing to about 1$\times$10$^{13}$ $\Omega$.cm at 500 kV/cm and reduce the interface state density of the LiNbO$_3$/Si(100) interface to about 1$\times$10$^{11}$ cm$^2$ . eV. Ferroelectric hysteresis measurements using a Sawyer-Tower circuit yielded remanent polarization (Pr) and coercive field (Ec) values of about 1.2 $\mu$C/cm$^2$ and 120 kV/cm, respectively.