• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1888-1893
• /
• 2011

Considering the dynamic performance and stability of railroad vehicles has begun to grab the attention because of developing the high speed train recently. A development based on an analysis of dynamics and verification has to be required to study the stability of vehicle performance. Several ways of analysis were using the look-up table to apply the wheel-rail contact characteristics quickly, whereas there is a constraint of the wheelset lateral displacement. In this study, an development of searching the wheel-rail contact position has been provided. The 2-point contact between wheel and rail during the driving condition can be calculated by numerical analysis. Moreover, a reliability is verified by comparing the result with a commercial program.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1341-1344
• /
• 2005

This study was aimed to verify the acceptable contact force between power collector and 3rd rail type conductor rail for the Korean standardized rubber-tired AGT light rail vehicle. The power collector was designed and manufactured to satisfy the Korean standardized Specifications of the rubber-tired AGT light rail vehicle. Based on the dynamic behavior, contact force variation and interruption in the worst installation tolerance of the conductor rail, its initial contact force was set up. At the test track for the Korean standardized rubber-tired AGT light rail vehicle, interruptions, stresses, vibrations, and contact force variations were measured. As the results, initial contact force was verified to ensure power collection stability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1277-1278
• /
• 2010

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.225-232
• /
• 2009

Infiltration of rainfall causes railway slopes to be unstable and may result in failure. Basic relationship between the rainfall and stability of railway embankment is defined to analyze its stability by rainfall. An experimental study for defining of infiltration rate of rainfall into slope is conducted in the lab. The results of Rainfall infiltration show that rainfall infiltration is not equal to infiltration as like reservoir because rate of rainfall infiltration is controlled by slope angle. Based on these results, boundary condition of rainfall is altered and various numerical analysis are performed. The variation of shear strength, the degree of saturation and pore-water pressure for railway slope during rainfall can be predicted and the safety factor of railway slope can be expressed as the function of rainfall amount, namely rainfall index. And suggested rainfall index is compared with the rail transport operation control which is used in KORAIL. It is judged that this rainfall index can be a good tool for the rail-transport operation control.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.115-118
• /
• 2007

The geometry of wheel and rail profiles is the primary contributor to wheel and rail interaction. These profiles interact to influence truck steering, vehicle lateral stability, wheel/rail wear and surface damage. Maintaining good control of the profiles is one of the keys to ensuring preferred wheel and rail interaction. Transportation Technology Center, Inc., Pueblo, Colorado, is developing an automated measurement system for wheel/rail contact condition inspections supported by AAR(Association of American Railroads). The system uses a modified version of $WRTOL^{TM}$ (Wheel/Rail Tolerances)--software that performs extensive analysis of wheel and rail contact conditions

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.800-806
• /
• 2011

Thermal expansion which occurs at the high speed rail joint is proportional to the free length from the point of fixity. This thermal expansion behaves similar to free expansion because the girder longitudinal stiffness is much larger than longitudinal resistance of rail pads. But the longitudinal displacement in the long rail is nominal because the longitudinal support condition of the girder is normally MFM(movable-fix-movable) system. Due to these girder expansion characteristics, there is longitudinal relative displacement at the rail pad and rail fastener spring which connects rail and girder. If the relative displacement between rail and girder is beyond the elastic limit for the rail pad, rail fastener system shall be applied using sliding fastener to prevent rail pad damage and fastener separation resulting from slip. On the other hand, train vertical vibration and tilting can occur due to the lack of fastener vertical force if the sliding fastener is applied at the girder joint. In the high speed rail bridge, vibration can occur due to the spring stiffness of the elastomeric bearing, also both vertical downward and upward displacement can occur. The elastomeric bearing vertical movement can cause rail displacement and finally the stability of the ballast is reduced because the gravel movement is induced.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.458-461
• /
• 2007

Recently, the continuous welded rail(CWR) track has been used for less maintenance of the High-speed railway tracks. In case of CWR track, track buckling has always been an unpredictable event under the high compressive stress in rail. The behavior and stress state of CWR track is manily influenced by its thermal variations, and it is important to understand seasonal variations of rail temperature and stress to predict the track stability. This paper describes the in-site measurement for the rail temperature and rail stress, and the correlation between the rail temperature and stress was examined.

• 한국방재학회 논문집
• /
• 제7권1호통권24호
• /
• pp.29-38
• /
• 2007

틸팅차량의 안정성 확보를 위해 궤도부담력과 주행안정성 검토가 이루어졌으며, 틸팅차량이 궤도부담력과 주행안정성 검토에 의해 산정된 허용속도로 운행될 경우 레일이음매 하부 노반침하에 대한 연구가 수행되었다. 열차 주행시 레일이음매와 장대레일에 작용하는 충격량이 다르기 때문에 장대레일 하부 노반에 대한 안정성 검토가 추가적으로 필요하다. 본 연구에서는 장대레일에 대하여 노반의 침하량 및 지지력을 수치해석을 통해 검토하고 허용침하량 및 허용지지력과 비교하여 노반의 안정성을 검토하였으며 레일이음매와 장대레일 하부 노반의 침하량 및 지지력을 비교 분석하였다. 그 결과, 장대레일 및 레일이음부 하부 노반의 침하량은 허용침하량의 71.2% 및 88.8%, 응력은 허용지지력의 10.4% 및 12.1%로 나타났다.

• 한국철도학회논문집
• /
• 제5권1호
• /
• pp.1-9
• /
• 2002

Where the track is continuously welded over the bridge, the longitudinal forces will be distributed interactively between the track and the sub-structure by the rail-bridge interaction mechanism. The ratio between the longitudinal forces transmitted in each elements depends on the magnitude of the ballast resistance and the stiffness of the sub-structures. In this paper, the main factors affect on the longitudinal rail force are discussed and the parametric study for the behavior of CWR(Continuous Welded Rail) track was executed. It is concluded that the horizontal ballast resistance and the stiffness of the bridge sub-structure are the significant parameters affecting the stability of the continuous welded rail track.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.679-685
• /
• 2003

Rotem has been using VAMPIRE for simulation and verification of the railway vehicle design. To improve the capability and accuracy of the analysis ability, ADAMS/Rail has been chosen as the next generation analysis tool. The dynamic performance of the railway vehicle, which is designed and manufactured by Rotem, is analyzed and simulated using ADAMS/Rail. The critical speed for linear and non-linear stability on tangent track, curving performance on various curved tractk, ride quality, derailment coefficient and the eigen values are calculated. In this paper, the results from ABAMS/Rail are compared with VAMPIRE's results.