• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.8
• /
• pp.325-329
• /
• 2003

Effects of thermal treatment on the structural properties of diamond-like carbon (DU) films were examined. The DLC films were deposited by using a modified filtered cathodic vacuum arc (FCVA) deposition system and by varying the negative substrate bias voltage, deposition time, and nitrogen flow rate. Thermal treatment on DLC films was performed using a rapid thermal annealing (RTA) process at $600^{\circ}C$ for 2min. Raman spectroscopy, x-ray photoemission spectroscopy (XPS), atomic force microscope (AFM), and surface profiler were used to characterize the I$_{D}$I$_{G}$ intensity ratio, sp$^3$ hybrid carbon fraction, internal stress, and surface roughness. It was found for all the deposited DLC films that the RTA-treatment results in the release of internal compressive stress, while at the same time it leds to the decrease of sp$^3$ fraction and the increase of I$_{D}$I$_{G}$ intensity ratio. It was also suggested that the thermal treatment effect on the structural property of DLC films strongly depends on the diamond-like nature (i.e., sp$^3$ fraction) of as-deposited film.ed film.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.115-120
• /
• 2023

ZnO/Cu/ZnO (ZCZ) thin film deposited on the glass substrate with DC and RF magnetron sputtering was rapid thermal annealed (RTA) and then effect of thermal temperature on the opto-electical and transparent heater properties of the films were considered. The visible transmittance and electrical resistivity are depends on the annealing temperature. The electrical resistivity decreased from 1.68 × 10^-3 Ωcm to 1.18 × 10^-3 Ωcm and the films annealed at 400℃ show a higher transmittance of 78.5%. In a heat radiation test, when a bias voltage of 20 V is applied to the ZCZ film annealed at 400℃, its steady state temperature is about 70.7℃. In a repetition test, the steady state temperature is reached within 15s for all of the bias voltages.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.1
• /
• pp.31-36
• /
• 2002

Low energy boron ions were implanted into the preamorphized and crystalline silicon substrates to form 0.2${\mu}m$ $p^+-n$ junctions. The rapid thermal annealing(RTA) was used to annihilate the crystal defects due to implantation and to activate the implanted boron ions, and the furnace annealing was employed to reflow the BPSG(bolo-phosphosilicate glass). The implantation conditions for Gepreamorphization were the energy of 45keV and the dose of 3$\times$1014cm-2. BF2 ions employed as a p-type dopant were implanted with the energy of 20keV and the dose of 2$\times$1015cm-2. The thermal conditions of RTA and furnace annealing were $1000^{\circ}C$/10sec and $850^{\circ}C$/40min, respectively. The junction depths were measured by SIMS and ASR techniques, and the 4-point probe was used to measure the sheet resistances. The electrical characteristics were analyzed via the leakage currents of the fabricated diodes. The single thermal processing with RTA produced shallow junctions of good qualities, and the thermal treatment sequence of furnace anneal and RTA yielded better junction characteristics than that of RTA and furnace anneal.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05a
• /
• pp.38-38
• /
• 1992

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.665-668
• /
• 1999

Thin films of Pb(Zr,Ti)O$_3$ were fabricated by means of the sol-gel spin-coating method and the multi-coating of eight coating numbers. The thin films were dried on the temperature range of 250 ~ 400($^{\circ}C$), whenever the specimens were dried after each coating Processing. The fabricated ferroelectric thin films of lead zirconate titanate(PZT) were treated with the rapid thermal annealing(RTA) at 650($^{\circ}C$),or 3(min), and direct insertion thermal annealing(DITA) at 650($^{\circ}C$), for 30(min). The measured properties of dielectric thin films were following: The good results of dielectric properties were shown by the RTA specimen. The saturation polarization(Ps), remanent polarization(Pr), coercive field (Ec), dielectric constant and dielectric loss factor of the RTA specimen were estimated to be about 27.1[ $\mu$ C/$\textrm{cm}^2$], 13.7[ $\mu$ C/$\textrm{cm}^2$], 55.6(kV/cm), 786 and 6.4(%) respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.136-139
• /
• 1999

The post-annealing treatments on RF (Radio Frequency) magnetron sputtered PZI(Pb$\_$1.05/(Zr$\_$0.52/, Ti$\_$0.48/)O$_3$thin films(4000${\AA}$) have been investigated. for a structure of PZT/Pt/Ti/SiO$_2$/Si Crystallization pproperties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature. We were able to obtain a perovskite structure of PZT at a low temperature of 600$^{\circ}C$. P-E curves of Pd/PZT/Pt capacitor annealed at 700$^{\circ}C$ demonstrate typical hysteresis loops. The measured values of P$\_$r/, E$\_$c/, by post annealed at 700$^{\circ}C$ were 12.1 ${\mu}$C/$\textrm{cm}^2$, 120KV/cm respectively.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.130-134
• /
• 2016

The influence of Au/Ni-based contact formed on a lightly-doped (7.3×1017cm−3, Zn-doped) InGaAsP layer for electrical compensation of surface plasmon polariton (SPP) propagation under various rapid thermal annealing (RTA) conditions has been studied. The active control of SPP propagation is realized by electrically pumping the InGaAsP multiple quantum wells (MQWs) beneath the metal planar waveguide. The metal planar film acts as the electric contact layer and SPP waveguide, simultaneously. The RTA process can lower the metal-semiconductor electric contact resistance. Nevertheless, it inevitably increases the contact interface morphological roughness, which is detrimental to SPP propagation. Based on this dilemma, in this work we focus on studying the influence of RTA conditions on electrical control of SPPs. The experimental results indicate that there is obvious degradation of electrical pumping compensation for SPP propagation loss in the devices annealed at 400℃ compared to those with no annealing treatment. With increasing annealing duration time, more significant degradation of the active performance is observed even under sufficient current injection. When the annealing temperature is set at 400℃ and the duration time approaches 60s, the SPP propagation is nearly no longer supported as the waveguide surface morphology is severely changed. It seems that eutectic mixture stemming from the RTA process significantly increases the metal film roughness and interferes with the SPP signal propagation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.3
• /
• pp.211-218
• /
• 2000

$PbZrO_3$precursor was prepared for the spin coating on the Pt/Ti/$SiO_2$/Si substrate. Two different heat treatment methods were used and the differencies were studied. One of the method is that the films were inserted into the furnace for 30 minutes and the other is that the films were annealed by rapid thermal annealing (RTA) for 1 minute at the same temperatures. We also examined the tendency of crystallization by annealing at the fixed temperature, $700^{\circ}C$ as a function of time, namely during 1, 10, 20, and 30 minitues, respectively. The optimum conditions for the crystallization of these films were at $550^{\circ}C$ during 30 min. and at $700^{\circ}C$ during 10 min. in muffle furnace and at $650^{\circ}C$ during 1 min in RTA furnace. The best condition for making good quality grains needs 30 min. at $700^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.130-135
• /
• 2003

Polycrystalline silicon thin films have been used for low cost thin film device application. However, it was very difficult to fabricate high performance poly-Si at a temperature lower than $600^{\circ}C$ for glass substrate because the crystallization process technologies like conventional solid phase crystallization (SPC) require the number of high temperature (600-$1000^{\circ}C$) process. The objective of this paper is to grow poly-Si on flexible substrate using a rapid thermal crystallization (RTC) of amorphous silicon (a-Si) layer and make the high temperature process possible on molybdenum substrate. For the high temperature poly-Si growth, we deposited the a-Si film on the molybdenum sheet having a thickness of 150 $\mu\textrm{m}$ as flexible and low cost substrate. For crystallization, the heat treatment was performed in a RTA system. The experimental results show the grain size larger than 0.5 $\mu\textrm{m}$ and conductivity of $10^{-5}$ S/cm. The a-Si was crystallized at $1050^{\circ}C$ within 3min and improved crystal volume fraction of 92 % by RTA. We have successfully achieved a field effect mobility over 67 $\textrm{cm}^2$/Vs.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1352-1354
• /
• 1998

$LiNbO_3$ transistor showed relatively stable characteristic, low interface trap density, and large remanent polarization. This paper reports ferroelectric $LiNbO_3$ thin films grown directly on p-type Si(100) substrates by 13.56 MHz rf magnetron sputtering system for FRAM applications. To take advantage of low temperature requirement for growing films, we deposited $LiNbO_3$ films lower than $300 ^{\circ}C$. RTA(Rapid Thermal Anneal) treatment was performed for as-deposited films in an oxygen atmosphere at $600^{\circ}C$ for 60 sec. We learned from X-ray diffraction that the RTA annealed films were changed from amorphous to poly-crystalline $LiNbO_3$ which exhibited (012), (015), and (022) orientations. The I-V characteristics of $LiNbO_3$ films before and after anneal treatment showed that RTA improved the leakage current of films. The leakage current density of films decreased from $10^{-5}$ to $10^{-7} A/cm^2$ at room temperature measurement. Breakdown electric field of the films exhibited higher than 500 kV/cm. The C-V curves showed the clockwise hysteresis represents ferroelectric switching characteristics. From C-V curves, we calculated dielectric constant of thin film $LiNbO_3$ as 27.5 which is close to that of bulk value.