• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.818-823
• /
• 2016

Millimeter wave (mm-wave) communication systems provide high data rates owing to the large bandwidths available at mm-wave frequencies. Recently, analogue and digital combined beamforming, namely "hybrid beamforming" has drawn attentions owing to its ability to realize the required link margins in mm-wave systems. Taking into account the radio frequency (RF) hardware limitations, such as the analogue phase shifter gain constraint and the low resolution of the phase controller, we introduce an uplink hybrid beamforming system that includes discrete Fourier transform (DFT) based "fixed" analogue beamforming. We adopt a zero-forcing (ZF) multiple-input multiple-output (MIMO) equalizer to eliminate the uplink inter-user interferences. Moreover, to improve the sum-rate performances, we propose a transmit beam selection algorithm which makes the uplink effective channels, i.e., the beamformed channels, become near orthogonal. The effectiveness of the proposed beam selection algorithm was verified through numerical simulations.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.6 s.360
• /
• pp.1-8
• /
• 2007

In wireless sensor network which uses limited battery, power consumption is very important factor for the survivality of the system. By using low-power communication to reduce power consumption, error rate is increased in typical conditions. This paper analyzes power consumption of specific error control coding (ECC) implementations. With identical link quality, ECC provides coding gain which save the power for transmission at the cost of computing power. In sensor node, transmit power is higher than computing power of Micro Controller Unit (MCU). In this paper, Viterbi algerian is applied to the low-transmit-power sensor networks in terms of network power consumption. Practically, Viterbi algorithm presents 20% of reduction of re-transmission in compared with Auto Repeat Request (ARQ) system. Furthermore, it is observed that network power consumption is decreased by almost 18%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.25-33
• /
• 1998

In this paper, we describe a single-gate MESFET mixer at PCS(Personal Communication Service) frequency band. The PCS frequency band is 1965~2025 MHz in FR and 140 MHz in IF irrespectly. The design of the mixer was executed by microwave simulator, EEsof Libra. The matching network is consisted of rectangular inductor, MIM capacitor and open stub. The ma- nufacture work was accomplished by the micro-pen and wedge-bonder. The mixer showed $6.69\pm0.65$ dB of conversion gain, $-14.9\pm3.5$dB of RF reflection coefficient and 57.83 dB of LO/IF isolation at 10 dBm of LO power when LO frequency is 1855 MHz. When this mixer is used at PCS terminal, IF-amplifier which compensates the conversion loss of diode mixer may be omitted.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.12
• /
• pp.1388-1398
• /
• 2012

SAR(Synthetic Aperture Radar) systems can provide images of wide coverage in day, night, and all-weather conditions. However wideband SAR systems are known to be vulnerable to interferences from other devices operating at in-band or adjacent spectrums and this may lead to image corruptions. In this paper, a SAR point target simulator is developed that provides performance analysis on image distortion caused by interferences from other devices. Interference signals are generated based on the experimental data observed from acquired SAR raw data. Simulation results include typical SAR performance measures such as spatial resolution, peak to sidelobe ratio and integrated sidelobe ratio. Finally, SAR target simulations are performed and shown to correspond to the image corruptions found in real SAR missions affected by RF interferences.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.53-59
• /
• 2018

In Korea, The number of installed LPG Charging stations is about 2000, increasing by 26 every year. In these, about 500 charging stations are older above 15 year, accounting about 25% of total stations. About 86% of them are located in the city, which is causing serious damage if accident occurs. In this paper, we developed a duel gas sensor module and integrated control system software that can prevent and correspondence to gas leaks and fire accidents at LPG/CNG charging stations. The dual type sensor module has the function of collecting and transmitting the measured data to the sensors of methane, butane and hydrogen through RF433Mhz communication. In addition, each sensor is attached with two to improve stability and accuracy. The integrated control system software detects real-time data of the devices measured by the sensors and it send to the PC and smart phone of manager. Therefore, if accident occurs, the manager can check the status of the charging station regardless of time and place.

• Journal of KIISE:Databases
• /
• v.37 no.3
• /
• pp.171-175
• /
• 2010

This paper analyzes the tag data inconsistency problem caused by incomplete execution of the tag access operation to the RFID tag's memory and proposes a protocol to control consistent tag data accesses with finalizing the incomplete operation. Passive RFID tag cannot guarantee complete execution of the tag access operations because of uncertainty and unexpected disconnection of RF communications. This leads to the tag data inconsistency problem. To handle this, we propose a concurrency control protocol which defines incomplete tag operations as continuous queries and monitors the tags're-observation continuously. The protocol finalizes the incomplete operation when the tag is re-observed while it blocks inconsistent data accesses from other operations. We justify the proposed protocol by analyzing the completeness and consistency. The experiments show that the protocol shows better performance than the traditional lock-based concurrency control protocol.

• Smart Media Journal
• /
• v.9 no.4
• /
• pp.60-65
• /
• 2020

The monopulse tracking algorithm can estimate the location of a partner station based on an RF (Radio Frequency) signal. The location of the partner station is estimated based on the monopulse ratio curve (MR-C), which is calculated based on the sum and difference signal patterns of an antenna. Therefore, the range in which the estimated location can be calculated with high accuracy increases in proportion to the linear region of MR-C. In this paper, we proposed a method to extend the linear region of the MR-C curve using the beamforming technique for the tracking antenna system using the active phased array antenna. Simulation results based on the same antenna system, it was confirmed that the linear region of MR-C was enlarged by about twice as much as the general case where the proposed method was not applied.

• International journal of advanced smart convergence
• /
• v.11 no.4
• /
• pp.96-103
• /
• 2022

This paper presents the analysis of increasing the resolution of True-Time-Delay (TTD) by 0.5-bit for phased-array antenna system which is one of the Multiple-Input and Multiple Output (MIMO) technologies. For the analysis, a 5.5-bit True-Time Delay (TTD) integrated circuit is designed and analyzed in terms of beam steering performance. In order to increase the number of effective bits, the designed 5.5-bit TTD uses Single Pole Triple Throw (SP3T) and Double Pole Triple Throw (DP3T) switches, and this method can minimize the circuit area by inserting the minimum time delay of 0.5-bit. Furthermore, the circuit mostly maintains the performance of the circuit with the fully added bits. The idea of adding 0.5-bit is verified by analyzing the relation between the number of bits and array elements. The 5.5-bit TTD is designed using 0.18 ㎛ RF CMOS process and the estimated size of the designed circuit excluding the pad is 0.57×1.53 mm². In contrast to the conventional phase shifter which has distortion of scanning angle known as beam squint phenomenon, the proposed TTD circuit has constant time delays for all states across a wide frequency range of 4 - 20 GHz with minimized power consumption. The minimum time delay is designed to have 1.1 ps and 2.2 ps for the 0.5-bit option and the normal 1-bit option, respectively. A simulation for beam patterns where the 10 phased-array antenna is assumed at 10 GHz confirms that the 0.5-bit concept suppresses the pointing error and the relative power error by up to 1.5 degrees and 80 mW, respectively, compared to the conventional 5-bit TTD circuit.

• International Journal of Computer Science & Network Security
• /
• v.23 no.7
• /
• pp.155-164
• /
• 2023

Machine learning with its high precision algorithms, Precision agriculture (PA) is a new emerging concept nowadays. Many researchers have worked on the quality and quantity of PA by using sensors, networking, machine learning (ML) techniques, and big data. However, there has been no attempt to work on trends of artificial intelligence (AI) techniques, dataset and crop type on precision agriculture using internet of things (IoT). This research aims to systematically analyze the domains of AI techniques and datasets that have been used in IoT based prediction in the area of PA. A systematic literature review is performed on AI based techniques and datasets for crop management, weather, irrigation, plant, soil and pest prediction. We took the papers on precision agriculture published in the last six years (2013-2019). We considered 42 primary studies related to the research objectives. After critical analysis of the studies, we found that crop management; soil and temperature areas of PA have been commonly used with the help of IoT devices and AI techniques. Moreover, different artificial intelligence techniques like ANN, CNN, SVM, Decision Tree, RF, etc. have been utilized in different fields of Precision agriculture. Image processing with supervised and unsupervised learning practice for prediction and monitoring the PA are also used. In addition, most of the studies are forfaiting sensory dataset to measure different properties of soil, weather, irrigation and crop. To this end, at the end, we provide future directions for researchers and guidelines for practitioners based on the findings of this review.

• Journal of Bio-Environment Control
• /
• v.31 no.3
• /
• pp.221-229
• /
• 2022

This study was aimed to investigate spatial and vertical characteristics of greenhouse environments according to the location of the environmental sensors, and to investigate the correlations between temperature, light intensity, and carbon dioxide (CO₂) concentration according to the type of greenhouse. Temperature, relative humidity (RH), CO₂, and light sensors were installed in the four-different vertical positions of the whole canopy as well as ground and roof space at the five spatial locations of the Venlo greenhouse. Also, correlations between temperature, light intensity, and CO₂ concentration in Venlo and semi-closed greenhouses were analyzed using the Curve Expert Professional program. The deviations among the spatial locations were larger in the CO₂ concentration than other environmental factors in the Venlo greenhouse. The average CO₂ concentration ranged from 465 to 761 µmol·mol^-1 with the highest value (646 µmol·mol^-1) at the Middle End (4ME) close to the main pipe (50Ø) of the liquefied CO₂ gas supply and lowest (436 µmol·mol^-1) at the Left Middle (5LM). The deviation among the vertical positions was greater in temperature and relative humidity than other environments. The time zone with the largest deviation in average temperature was 2 p.m. with the highest temperature (26.51℃) at the Upper Air (UA) and the lowest temperature (25.62℃) at the Lower Canopy (LC). The time zone with the largest deviation in average RH was 1 p.m. with the highest RH (76.90%) at the LC and the lowest RH (71.74%) at the UA. The highest average CO₂ concentration at each hour was Roof Air (RF) and Ground (GD). The coefficient of correlations between temperature, light intensity, and CO₂ concentration were 0.07 for semi-closed greenhouse and 0.66 for Venlo greenhouse. All the results indicate that while the CO₂ concentration in the greenhouse needs to be analyzed in the spatial locations, temperature and humidity needs to be analyzed in the vertical positions of canopy. The target CO₂ fertilization concentration for the semi-closed greenhouse with low ventilation rate should be different from that of general greenhouses.