• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.83-91
• /
• 2017

Objectives: The purpose of this study was to evaluate the error of the leaf position accuracy of the MLC due to the gravity effect according to the gantry angle by using picket fence test using EPID and GafChromic EBT3 film. Materials and Methods: A 5 cm solid phantom was placed on the table and the SAD was set to 100 cm. The EBT3 film was placed exactly over the solid phantom and covered a 1.5 cm solid phantom and the picket fence test was performed. The EPID was measured under the same conditions as the EBT3 film at SID 100 cm. The gantry angles were measured at $0^{\circ}$, $90^{\circ}$, $180^{\circ}$ and $270^{\circ}$ in order to evaluate the position of the MLC according to the gantry angle. For the geometric evaluation of the MLC, the leaf position accuracy of the MLC was analyzed using the analysis program. Results: In case of EPID, when the gantry angle was changed to $0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, the difference of the position errors of the leaves was 0.18 mm, 0.31 mm, 0.20 mm, 0.26 mm on the average and the maximum values of the errors were respectively 0.44 mm, 0.54 mm, 0.34 mm, 0.44 mm. In case of EBT3 film, when the gantry angle was changed to $0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, the difference of the position errors of the leaves was 0.19 mm, 0.21 mm, 0.19 mm, 0.31 mm on the average and the maximum values of the errors were respectively 0.35 mm, 0.45 mm, 0.36 mm, 0.48 mm. Conclusion: In this study, we analyzed the position error of the leaf of the MLC according to the gantry angle, and confirmed the position error of the leaf by gravity effect. As a result of comparing the leaf position accuracy using EPID and EBT3 film according to the variation of gantry angle, a larger error occurred in the error analysis method using EPID than that of EBT3 film. Therefore, in the case of IMRT based on MLC, as well as verification of accurate dosimetry should be conducted, it is considered that the quality control and verification for the precise operation of the MLC will be needed. and it is necessary to compare and verify the method of analysis.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.7
• /
• pp.380-394
• /
• 2015

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2014. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of heat and mass transfer, cooling and heating, and air-conditioning, the flow inside building rooms, and smoke control on fire. Research issues dealing with duct and pipe were reduced, but flows inside building rooms, and smoke controls were newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for thermal contact resistance measurement of metal interface, a fan coil with an oval-type heat exchanger, fouling characteristics of plate heat exchangers, effect of rib pitch in a two wall divergent channel, semi-empirical analysis in vertical mesoscale tubes, an integrated drying machine, microscale surface wrinkles, brazed plate heat exchangers, numerical analysis in printed circuit heat exchanger. In the area of pool boiling and condensing, non-uniform air flow, PCM applied thermal storage wall system, a new wavy cylindrical shape capsule, and HFC32/HFC152a mixtures on enhanced tubes, were actively studied. In the area of industrial heat exchangers, researches on solar water storage tank, effective design on the inserting part of refrigerator door gasket, impact of different boundary conditions in generating g-function, various construction of SCW type ground heat exchanger and a heat pump for closed cooling water heat recovery were performed. (3) In the field of refrigeration, various studies were carried out in the categories of refrigeration cycle, alternative refrigeration and modelling and controls including energy recoveries from industrial boilers and vehicles, improvement of dehumidification systems, novel defrost systems, fault diagnosis and optimum controls for heat pump systems. It is particularly notable that a substantial number of studies were dedicated for the development of air-conditioning and power recovery systems for electric vehicles in this year. (4) In building mechanical system research fields, seventeen studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, and renewable energies, piping in the buildings. Proposed designs, performance performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the evaluation of work noise in tunnel construction and the simulation and development of a light-shelf system. The subjects of building energy were worked on the energy saving of office building applied with window blind and phase change material(PCM), a method of existing building energy simulation using energy audit data, the estimation of thermal consumption unit of apartment building and its case studies, dynamic window performance, a writing method of energy consumption report and energy estimation of apartment building using district heating system. The remained studies were related to the improvement of architectural engineering education system for plant engineering industry, estimating cooling and heating degree days for variable base temperature, a prediction method of underground temperature, the comfort control algorithm of car air conditioner, the smoke control performance evaluation of high-rise building, evaluation of thermal energy systems of bio safety laboratory and a development of measuring device of solar heat gain coefficient of fenestration system.

• Journal of radiological science and technology
• /
• v.39 no.1
• /
• pp.99-105
• /
• 2016

The noise power spectrum (NPS) is one of the most general methods for measuring the noise amplitude and the quality of an image acquired from a uniform radiation field. The purpose of this study was to compare different NPS methodologies by using megavoltage X-ray energies. The NPS evaluation methods in diagnostic radiation were applied to therapy using the International Electro-technical Commission standard (IEC 62220-1). Various radiation therapy (RT) devices such as TrueBeam$^{TM}$(Varian), BEAMVIEW$^{PLUS}$(Siemens), iViewGT(Elekta) and Clinac$^R$ iX (Varian) were used. In order to measure the region of interest (ROI) of the NPS, we used the following four factors: the overlapping impact, the non-overlapping impact, the flatness and penumbra. As for NPS results, iViewGT(Elekta) had the higher amplitude of noise, compared to BEAMVIEW$^{PLUS}$ (Siemens), TrueBeam$^{TM}$(Varian) flattening filter, Clinac$^{R}$iXaS1000(Varian) and TrueBeam$^{TM}$(Varian) flattening filter free. The present study revealed that various factors could be employed to produce megavoltage imaging (MVI) of the NPS and as a baseline standard for NPS methodologies control in MVI.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.427-446
• /
• 2008

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 2006 has been accomplished. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environments. The conclusions are as follows. (1) The research trends of fluid engineering have been surveyed as groups of general fluid flow, fluid machinery and piping, etc. New research topics include micro heat exchanger and siphon cooling device using nano-fluid. Traditional CFD and flow visualization methods were still popular and widely used in research and development. Studies about diffusers and compressors were performed in fluid machinery. Characteristics of flow and heat transfer and piping optimization were studied in piping systems. (2) The papers on heat transfer have been categorized into heat transfer characteristics, heat exchangers, heat pipes, and two-phase heat transfer. The topics on heat transfer characteristics in general include thermal transport in a cryo-chamber, a LCD panel, a dryer, and heat generating electronics. Heat exchangers investigated include pin-tube type, plate type, ventilation air-to-air type, and heat transfer enhancing tubes. The research on a reversible loop heat pipe, the influence of NCG charging mass on heat transport capacity, and the chilling start-up characteristics in a heat pipe were reported. In two-phase heat transfer area, the studies on frost growth, ice slurry formation and liquid spray cooling were presented. The studies on the boiling of R-290 and the application of carbon nanotubes to enhance boiling were noticeable in this research area. (3) Many studies on refrigeration and air conditioning systems were presented on the practical issues of the performance and reliability enhancement. The air conditioning system with multi indoor units caught attention in several research works. The issues on the refrigerant charge and the control algorithm were treated. The systems with alternative refrigerants were also studied. Carbon dioxide, hydrocarbons and their mixtures were considered and the heat transfer correlations were proposed. (4) Due to high oil prices, energy consumption have been attentioned in mechanical building systems. Research works have been reviewed in this field by grouping into the research on heat and cold sources, air conditioning and cleaning research, ventilation and fire research including tunnel ventilation, and piping system research. The papers involve the promotion of efficient or effective use of energy, which helps to save energy and results in reduced environmental pollution and operating cost. (5) Studies on indoor air quality took a great portion in the field of building environments. Various other subjects such as indoor thermal comfort were also investigated through computer simulation, case study, and field experiment. Studies on energy include not only optimization study and economic analysis of building equipments but also usability of renewable energy in geothermal and solar systems.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.17 no.2
• /
• pp.3-9
• /
• 2013

Purpose: Currently commercially available phantom can reproduce and evaluate only a static situation, the study is incomplete research on phantom and system which is can confirmed functional situation in the kidney by time through dynamic phantom and blood flow velocity, various difference according to the amount of radioactive. Therefore, through this study, it has produced the dynamic kidney phantom to reproduce images through the dynamic flow of the kidney, it desire to evaluate the usefulness of nuclear medicine imaging. Materials and Methods: The production of the kidney phantom was fabricated based on the normal adult kidney, in order to reproduce the dynamic situation based on the fabricated kidney phantom, in this study it was applied the volume pump that can adjust the speed of blood flow, so it can be integrated continuously radioactive isotopes in the kidney by using $^{99m}Tc-pertechnate$. Used the radioactive isotope was supplied through the two pump. It was confirmed the changes according to the infusion rate, radioactive isotopes and the different injection speeds on the left and right, analysis of the acquired images was done by drawn ten times ROI in order to check the reproducibility of each on the front and rear of the kidney and bladder. Results: Under the same conditions infusion rate 40 mL/min fixed to adjust the pressure of the pump when the radiopharmaceuticals between 2-3 minutes in the most integrated in the kidney phantom was excreted inthe bladder. Glomerular filtration rate (GFR), respectively, by each device SYMBIA 1,091 mL/min, FORTE 1,232 mL/min, ARGUS 1,264 mL/min, INFINIA 1,302 mL/min in that there isno statistically significant difference was found, Tmax values and T1/2 values stars from all equipment with no statistically significant difference was found. CV values of the coefficient of variation less than 5% was found to be repeatable, and to 2.67% of the lowest SYMBIA appeared, INFINIA was the highest in the 4.86%. Conclusion: Through this study, the results showed that the dynamic kidney phantom system is able to similarly reproduce renogram in the actual clinical. Especially, the depicted over time for the flow to be excreted through the kidney into the bladder was adequately reproduce, it is expected to be utilized as basic data to check the quality of the dynamic images. In addition, it is considered to help in the field of functional imaging and quality control.

• Journal of Bio-Environment Control
• /
• v.21 no.3
• /
• pp.207-212
• /
• 2012

The objective of the present study is to identify the physico-chemical characteristics of used plug media (UPM) and its effect on growth response of tomato and cucumber seedlings. The UPM from commercial media Mix#5 (Sungro co., Ltd.) was used in this study. This media was sterilized by sterilizer at $120^{\circ}C$ in 30 minutes at 1.5 atm. Physicochemical properties of UPM was compared with new plug media (NPM). Physical properties such as air volume, particle density, solid volume, bulk density were investigated by three phase device (DIK-1130, Japan). And chemical characteristics such as $NO_3$-N, $P_2O_5$, K, Mg, Ca, $SiO_2$, CEC, OM were investigated by soil spectrophotometer (PTIZEN 1412SA, Mecasys Co., Ltd). The result indicates that air volume and water holding capacity of UPM are lower than NPM (25%, 15%, respectively). Bulk density and soil weight are more than two times higher than NPM per unit volume. Compared to NPM, there were no significant different for pH and EC. But CEC of UPM is lower than NPM 40%. In order to compare growth response and ability absorption of inorganic elements by plants, cucumber and tomato seedlings were used and chemical characteristics after growing of mediums were determined. The result indicated that seeding quality of tomato and cucumber in UPM is less than in NPM and almost inorganic ions of UPM are lower than NPM. So it is necessary to improve physicochemical properties of UPM.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.249-254
• /
• 2022

With the rapid advance of the semiconductor and Information and communication technologies, remote environment monitoring technology, which can detect and analyze surrounding environmental conditions with various types of sensors and wireless communication technologies, is also drawing attention. However, since the conventional remote environmental monitoring systems require external power supplies, it causes time and space limitations on comfortable usage. In this study, we proposed the concept of the self-powered remote environmental monitoring system by supplying the power with the levitation-electromagnetic generator (L-EMG), which is rationally designed to effectively harvest biomechanical energy in consideration of the mechanical characteristics of biomechanical energy. In this regard, the proposed L-EMG is designed to effectively respond to the external vibration with the movable center magnet considering the mechanical characteristics of the biomechanical energy, such as relatively low-frequency and high amplitude of vibration. Hence the L-EMG based on the fragile force equilibrium can generate high-quality electrical energy to supply power. Additionally, the environmental detective sensor and wireless transmission module are composed of the micro control unit (MCU) to minimize the required power for electronic device operation by applying the sleep mode, resulting in the extension of operation time. Finally, in order to maximize user convenience, a mobile phone application was built to enable easy monitoring of the surrounding environment. Thus, the proposed concept not only verifies the possibility of establishing the self-powered remote environmental monitoring system using biomechanical energy but further suggests a design guideline.

• Journal of Intelligence and Information Systems
• /
• v.27 no.1
• /
• pp.191-207
• /
• 2021

Up to this day, mobile communications have evolved rapidly over the decades, mainly focusing on speed-up to meet the growing data demands of 2G to 5G. And with the start of the 5G era, efforts are being made to provide such various services to customers, as IoT, V2X, robots, artificial intelligence, augmented virtual reality, and smart cities, which are expected to change the environment of our lives and industries as a whole. In a bid to provide those services, on top of high speed data, reduced latency and reliability are critical for real-time services. Thus, 5G has paved the way for service delivery through maximum speed of 20Gbps, a delay of 1ms, and a connecting device of 106/㎢ In particular, in intelligent traffic control systems and services using various vehicle-based Vehicle to X (V2X), such as traffic control, in addition to high-speed data speed, reduction of delay and reliability for real-time services are very important. 5G communication uses high frequencies of 3.5Ghz and 28Ghz. These high-frequency waves can go with high-speed thanks to their straightness while their short wavelength and small diffraction angle limit their reach to distance and prevent them from penetrating walls, causing restrictions on their use indoors. Therefore, under existing networks it's difficult to overcome these constraints. The underlying centralized SDN also has a limited capability in offering delay-sensitive services because communication with many nodes creates overload in its processing. Basically, SDN, which means a structure that separates signals from the control plane from packets in the data plane, requires control of the delay-related tree structure available in the event of an emergency during autonomous driving. In these scenarios, the network architecture that handles in-vehicle information is a major variable of delay. Since SDNs in general centralized structures are difficult to meet the desired delay level, studies on the optimal size of SDNs for information processing should be conducted. Thus, SDNs need to be separated on a certain scale and construct a new type of network, which can efficiently respond to dynamically changing traffic and provide high-quality, flexible services. Moreover, the structure of these networks is closely related to ultra-low latency, high confidence, and hyper-connectivity and should be based on a new form of split SDN rather than an existing centralized SDN structure, even in the case of the worst condition. And in these SDN structural networks, where automobiles pass through small 5G cells very quickly, the information change cycle, round trip delay (RTD), and the data processing time of SDN are highly correlated with the delay. Of these, RDT is not a significant factor because it has sufficient speed and less than 1 ms of delay, but the information change cycle and data processing time of SDN are factors that greatly affect the delay. Especially, in an emergency of self-driving environment linked to an ITS(Intelligent Traffic System) that requires low latency and high reliability, information should be transmitted and processed very quickly. That is a case in point where delay plays a very sensitive role. In this paper, we study the SDN architecture in emergencies during autonomous driving and conduct analysis through simulation of the correlation with the cell layer in which the vehicle should request relevant information according to the information flow. For simulation: As the Data Rate of 5G is high enough, we can assume the information for neighbor vehicle support to the car without errors. Furthermore, we assumed 5G small cells within 50 ~ 250 m in cell radius, and the maximum speed of the vehicle was considered as a 30km ~ 200 km/hour in order to examine the network architecture to minimize the delay.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.36 no.4
• /
• pp.344-349
• /
• 2016

This study was conducted to evaluate the possibility of expanding the usage of whole crop silage from beef cattle and dairy cow to hogs and chickens. For this purpose, a crushing device was developed to crush whole crop silage. The crushed silage was sealed, and analyzed for its feed value. The silage varieties used for the experiment included Saessal barley and Geumgang wheat. Whole crop barley and wheat were crushed in the crushing system as a whole without separating stems, leaves, grains, etc.. When the crushed whole crop silages (CWCS) were analyzed, full grain, grains above 10 mm in size, grains 5~10 mm in size, and grains below 5 mm in size accounted for, 20%, 4%, 27%, and 49 %, respectively. In order to facilitate the fermentation of CWCS, inoculated some fermenter into each CWCS sample (barley or wheat). As control, another set of sample was not inoculated. Crude protein (CP), ether extract (EE), crude fiber (CF), neutral detergent fiber (NDF), acid detergent fiber (ADF), lignin, cellulose content, total digestible nutrient (TDN), and relative feed value (RFV) of fermenter-inoculated Saessal barley were 2.45 %, 1.61%, 8.95%, 16.94%, 9.52%, 1.01%, 8.51%, 81.38%, and 447.5%, respectively. The CP, EE, CF, NDF, ADF, lignin, cellulose content, TDN, and RFV in the other sample of Saessal barley without inoculation of fermenter were 2.57%, 1.62%, 9.61%, 18.25%, 10.13%, 1.10%, 9.04%, 80.90%, and 412.9%, respectively. The CP, EE, CF, NDF, ADF, lignin, cellulose content, TDN, and RFV of fermenter-inoculated Geumgang wheat sample were 2.43%, 1.27%, 10.99%, 19.49%, 11.23%, 1.46%, 9.77%, 80.03%, and 382.6%, respectively. The CP, EE, CF, NDF, ADF, lignin, cellulose content, TDN, RFV of the other set sample of Geumgang wheat sample without the inoculation of fermenter were 2.28%, 1.44%, 10.08%, 18.02%, 10.44%, 1.26%, 9.18%, 80.65%, and 416.9%, respectively. The TDN and RFV content in the fermenter-inoculated Saessal barley were 81.38% and 447.5%, respectively, while the one in the fermenter-inoculated Geumgang wheat were 80.03% and 382.6% respectively. When the feed value of whole crop barley and wheat silage without crushing process was compared to the feed value of whole crop barley and wheat silage made from crushing system, the latter appeared to be higher than the former. This could be due to the process of sealing the crushed silage which might have minimized air content between samples and shortened the golden period of fermentation. In conclusion, these results indicate that a crushing process might be needed to facilitate fermentation and improve the quality of silage when making whole crop silage.

• (The) Research of the performance art and culture
• /
• no.20
• /
• pp.5-30
• /
• 2010

It has been diversified and serious attempt to establish the identity of Changgeuk, but it is still independent dramaturgy or the current unformed progressive art. In this situation, exploring works of the identity of changgeuk that is base on the performed individual and specific works in the title of Changgeuk is needed. The 80s and 90s Heo, Gyu was leading an active life as a director who was responsible for directing of Changgeuk. He dramatized Siljeon Pansori -which is a group of Pansori missing text- as well as 5-remained Songs in Pansori and he presented a number of creative Changgeuk works on stage. Especially, the completion of dramatizing 5-remained Songs in Pansori under the name of 'Wanpan Changgeuk -which means full version performance without omit-' is the one of his big achievement by performing "Heungbojeon" on the stage 1982 and "Jeokbyeokga" 1985. The purposes of this research are confirmation of Heo's direction of the formulation and considering its characteristics & significance through 'Wanpan Changgeuk' which written by Heo. Heo was a practical play who was interested in the subjective formulation of national culture and creative transmission for Korean traditional performance. He tried to formulate Changgeuk to a representative performance of Korea. In the process he pointed out those problems, (1) interpretation of a work problem, (2) actor's creative problems, (3) structure problem of theater for Changgeuk. He indicated that the other challenges are to use of the stage & device, to overcome sentimentalism, to stylize acting, to improve own quality, to control the speed and length of the song, to choose the suitable musical accompaniment, to create new repertories problems, and etc. Changgeuk is classified in 3 group by origin, (1)dramatizing of 5-remained Songs, (2)dramatizing of 7-missing Songs, (3)creative dramatizing. It contains all of 3 types that Heo's work. The dramatizing of remained 5 Songs are the great importance among those works. Heo hoped that Chaggeuk has become the most representative art work of Korea by performing 'Wanpan Changgeuk' compiled heritage of Korea's outstanding artistic achievement. The characteristics of 'Wanpan Changgeuk' can be summarized following four. (1) Directing attitudes that emphasizes tradition, (2) Accepting the elements of traditional performance actively, (3) Valuing the classy and ethic, (4) Emphasizing humor and active utilizing of the secondary characters. Heo's 'Wanpan Changgeuk' shows a peak of the artistic level which Changgeuk can be reached. He want to make Changgeuk a Korean representative artistic performance by compiling Pansori heritage and accommodating Korean traditional performance. Heo continued his effort to present Pansori's authenticity and to dramatize from beginning to end without missing. It shows very well that 'Wanpan Changgeuk' takes 4~5 hours for playing. It looks Heo's achievement in the 'Wanpan Changgeuk' influenced Changgeuk significantly since then. Heo's 'Wanpan Changgeuk' is matrix of 'Wanpan JangMak Changgeuk' attempted in the 1990s. Especially, their intent is consistent to synthesize texts and to show all the virtue of Pansori. But 90's 'Wanpan JangMak Changgeuk' aim for large stage, fancy device & costume and variety contents compared with 'Wanpan Changgeuk'. Recently, producers have tried not to make a impressive Changgeuk but to make a interesting one. They usually organize performance within 2 hours and prefer orchestral music to its unique sound. In those point of view, it seems that Heo's idle in 'Wanpan Changgeuk' has become one of target to conquer in these days.