• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.97-105
• /
• 2012

The effects of pH, types of applied current, agitation method and time, additive on the amount of co-deposited $TiO_2$ particles in the matrix were investigated. The deposition rates increased with increasing pH values, while the volume fraction of $TiO_2$ particles and the size of agglomerated $TiO_2$ particles in the composite decreased. The volume fraction of $TiO_2$ particles in the composite decreased when pulsed current of 50% duty cycle was used. And the size of agglomerated $TiO_2$ particles in the nickel matrix of pulsed current was smaller than that of DC current specimen. The volume fraction of $TiO_2$ particles in the matrix decreased with longer time by air agitation, but in case of using magnetic bar, volume fraction in the same range of time was relatively constant. The volume fraction of the electrodeposited Ni-$TiO_2$ composite in the solution containing 0.01 M Dimethylamine borane (DMAB) increased slightly with increasing agitation time regardless of agitation methods. Thermal stability of the electrodeposited Ni-$TiO_2$ composite increased with lower pH at the temperature range of $200{\sim}800^{\circ}C$, and the results showed that the amount of co-deposited $TiO_2$ relies more on the deposition rate than zetapotential of $TiO_2$ particles.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.201.2-201.2
• /
• 2016

The triggered vacuum switch (TVS) is widely used as a high power switch in the field of pulsed power application. TVS can produce current of higher than 100 kA within a microsecond after being triggered. A triggering high voltage pulse generator supplies a high voltage signal to the trigger system to initiate the discharge between a trigger pin and one of main electrode. The trigger system, which consists of a tungsten trigger electrode and cylindrical ceramic insulator around it, is normally installed at the center of main cathode electrode. The discharging characteristics of the trigger system strongly depend on the geometry, electrode material, vacuum pressure and so on. In addition, we especially will focus on the developing a triggering pulse generator, which can vary not only value of voltage but also pulse duration, because its properties gives pivot influences on the TVS discharge. To verify such effects, we made a 3.3 kJ TVS set-up initially. Thus we will discuss some of prominent results from 3.3 kJ TVS system. In parallel we will show on the design of 300 kJ TVS system for the high current in the future.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.3
• /
• pp.40-47
• /
• 1999

We have established a pulsed low-energy large-aIXTture electron beam(LELAEB) generation system with an energy of 2OO[keV], current of 1[A], pulse repetition rate of 200[Hz], and several tens of ${\mu}s$ pulse width. The system is characterized by a cold cathode that is simpler than the hot cathode. Electron beam does not need to be scanned over target objects because of large beam aIXTture of $300[\textrm{cm}^2]$. Electron source is secondary electrons that are generated when the ions from the glow discharge collide on the cathode surface. In this paper, We report about the design and manufacture of LELAEB generation system based on the theoretical analysis in order to study lXlssibility of increasing the efficiency of IELAEB accelerator. We also report on the possibility of large aperture beam current generation and the current density uniformity based on the experiIrental results.esults.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1282-1284
• /
• 1998

ZnO Varistor is an electronic ceramic device for controlling the surge voltage from low level to high. In this study, the puncture mechanism occurring in ZnO varistor is investigated, and the simulation for restraining the puncture by formulating the relation between the applied voltage and the increase of the inside temperature of grain is applied. In order to simulate the cause of the current localization which is the primary factor causing the puncture, the localization phenomenon and the temperature distribution induced by the localized current, the Voronoi network is applied, which can realize the structure of the practical varistor better than the established simple network. Using the current through each grain and the voltage applied to the grain boundary obtained from that simulation, the Joule heating energy is calculated and the phenomenon that the puncture occurs can be analyzed quantitatively by simulating the electric and thermal characteristics according to the externally applied pulsed voltage.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.107-112
• /
• 2005

We present an AlGaN/GaN metal-insulator-semiconductor-heterostructure field effect transistor (MIS-HFET) with an $Al_2O_3-HfO_2$ laminated high-k dielectric, deposited by plasma enhanced atomic layer deposition (PEALD). Based on capacitance-voltage measurements, the dielectric constant of the deposited $Al_2O_3-HfO_2$ laminated layer was estimated to be as high as 15. The fabricated MIS-HFET with a gate length of 102 m exhibited a maximum drain current of 500 mA/mm and maximum tr-ansconductance of 125 mS/mm. The gate leakage current was at least 4 orders of magnitude lower than that of the reference HFET. The pulsed current-voltage curve revealed that the $Al_2O_3-HfO_2$ laminated dielectric effectively passivated the surface of the device.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.314-319
• /
• 2015

Invar is a compound metal of Fe-Ni system contained 36.5% Ni. The characteristic of invar is that the coefficient of thermal expansion is $1.0{\times}10^{-6}cm/^{\circ}C$. It is approximately 10 times smaller than series of steel. Because of this low thermal expansion characteristic of Invar, it is used to shadow mask of display device such as UHDTV or OLED TV. In this study, pulse current from pulse generator instead of DC current is used to overcome the disadvantages of the conventional electrochemical machining. Pulsed current with different duty factor in PECM affect the precise geometry. Pulse electrochemical machining is conducted to machine the micro hole to the invar sheet with different duty factor. The machined shape and overcut of invar sheet with different duty factor is observed by optical microscope and scanning electron microscope (SEM).

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.333-337
• /
• 2020

Orthorhombic DyMnO₃ films are fabricated epitaxially on Nb-1.0 wt%-doped SrTiO₃ single crystal substrates using pulsed laser deposition technique. The structure of the deposited DyMnO₃ films is studied by X-ray diffraction, and the epitaxial relationship between the film and the substrate is determined. The electrical transport properties reveal the diodelike rectifying behaviors in the all-perovskite oxide junctions over a wide temperature range (100 ~ 340 K). The forward current is exponentially related to the forward bias voltage, and the extracted ideality factors show distinct transport mechanisms in high and low positive regions. The leakage current increases with increasing reverse bias voltage, and the breakdown voltage decreases with decrease temperature, a consequence of tunneling effects because the leakage current at low temperature is larger than that at high temperature. The determined built-in potentials are 0.37 V in the low bias region, and 0.11 V in the high bias region, respectively. The results show the importance of temperature and applied bias in determining the electrical transport characteristics of all-perovskite oxide heterostructures.

• Progress in Superconductivity
• /
• v.2 no.2
• /
• pp.71-75
• /
• 2001

The effect of annealing step-edges of LaAlO$_3$ and MgO single crystal substrates on YBa$_2$Cu$_3$O$_{7}$ junction has been studied. The step-edge was fabricated by argon ion milling and was annealed at 105$0^{\circ}C$ in 1 attn oxygen pressure. We compared AFM image near step-edge of the substrates between before and after annealing process. And YBa$_2$Cu$_3$O$_{7}$ thin film was deposited on the step-edge by a standard pulsed laser deposition. The step-edge junctions were characterized by current-voltage curves at 77 K. The annealing of step-edges of MgO substrate improved the current-voltage characteristic of Josephson junction: double steps in the current-voltage characteristic disappeared. However the annealing for LaAlO$_3$ did not improve the junction property.rty.

• Journal of Korean Neuropsychiatric Association
• /
• v.57 no.2
• /
• pp.119-132
• /
• 2018

Despite the fact that pharmacotherapy depressive disorders have proven efficacy, a substantial number of patients are resistant to conventional management. As neuroscientific research about pathophysiology of depression have accumulated, repeated transcranial magnetic stimulation (rTMS) and transcranial direct current stimulation (tDCS) have emerged as an important mechanism-based treatment modality. This overview provides a review of therapeutic application of rTMS and tDCS in patients with depression. The clinical and basic studies of rTMS and tDCS in depression were reviewed and integrated using a literature review and interview with experts. rTMS is a noninvasive procedure of a localized pulsed magnetic field to the surface of the head to cause a depolarization of neurons in the brain cortex. tDCS has a mechanism of modulating cortical excitability in a polarity-specific manner without eliciting action potentials. rTMS and tDCS seem promising for treating depression. Although therapeutic parameters and further technical improvement remain to be systematically investigated, rTMS and tDCS would be a safe and effective intervention to treat depression.

• Journal of Pharmaceutical Investigation
• /
• v.40 no.1
• /
• pp.23-31
• /
• 2010

In our previous work on levodopa delivery at pH 2.5 using iontophoresis, we found that cathodal delivery showed higher permeation than anodal delivery and electroosmosis plays more dominant role than electrorepulsion. In this work, we studied the transdermal transport of levodopa at very low pH (pH=1.0) where all levodopa molecules are cations, and evaluated some factors which affect the transdermal transport. The transport study at pH 2.5 was also conducted for comparison. The contribution of electrorepulsion and electroosmosis on flux was also evaluated. Using stable aqueous solution, the effect of electrode polarity, current density, current type and drug concentration on transport through skin were studied and the results were compared. We also investigated the iontophoretic flux from hydroxypropyl cellulose (HPC) hydrogel containing levodopa. In vitro flux study was performed at $33^{\circ}C$, using side-by-side diffusion cell. Full thickness hairless mouse skin were used. Current densities applied were 0.2, 0.4 or $0.6\;mA/cm^2$. Contrary to the pH 2.5 result, anodal delivery showed higher flux, indicating that electrorepulsion is the dominant force for the transport, overcoming the electroosmotic flow which is acting against the direction of electrorepulsion. Cumulative amount of levodopa transported was increased as the current density or drug concentration was increased. When amount of current dose was constant, continuous current was more beneficial than pulsed current in promoting levodopa permeation. Similar transport results were obtained when hydrogel was used as the donor phase. These results indicate that iontophoretic delivery of zwitterion such as levodopa is much complicated than that can be expected from small ionic molecules. The results also indicate that, only at very low pH like pH 1.0, electrorepulsion can be the dominant force over the electroosmosis in the levodopa transport.