• Journal of Power Electronics
• /
• 제12권5호
• /
• pp.708-714
• /
• 2012

This paper presents a new interleaved pulse-width modulation (PWM) boost-flyback converter to achieve power factor correction (PFC) and regulate DC bus voltage. The adopted boost-flyback converter has a high voltage conversion ratio to overcome the limit of conventional boost or buck-boost converter with narrow turn-off period. The proposed converter has wide turn-off period compared with a conventional boost converter. Thus, the higher output voltage can be achieved in the proposed converter. The interleaved PWM can further reduce the input and output ripple currents such that the sizes of inductor and capacitor are reduced. Since boundary conduction mode (BCM) is adopted to achieve power factor correction, power switches are turned on at zero current switching (ZCS) and switching losses are reduced. The circuit configuration, principle operation, system analysis, and design consideration of the proposed converter are presented in detail. Finally, experiments conducted on a laboratory prototype rated at 500W were presented to verify the effectiveness of the converter.

• Journal of Power Electronics
• /
• 제10권5호
• /
• pp.518-527
• /
• 2010

This paper presents a new technique for directly designing a linear digital controller for a single-phase pulse width modulation (PWM) converter systems, based on closed-loop identification. The design procedure consists of three steps. First, obtain a digital current controller for the inner loop system by using the error space approach, so that the power factor of the supply is close to one. The outer loop is composed of a voltage controller, a current control loop including a current controller, a PWM converter, and a capacitor. Then, all the components, except the voltage controller, are identified by a discrete-time equivalent linear model, using the closed-loop output error (CLOE) method. Based on this equivalent model, a proper digital voltage controller is then directly designed. It is shown through PSim simulations and experimental results that the proposed method is useful for the practical design of PWM converter controllers.

• 한국전자통신학회논문지
• /
• 제12권4호
• /
• pp.607-614
• /
• 2017

본 연구에서는 마이크로 컨트롤러를 기반으로 한 PWM 제어 기술을 통해 스마트폰 무선충전을 위한 강압 컨버터를 설계 및 제작하였다. 전압센서를 이용해 출력전압이 기준전압을 따라가도록 피드백 제어 회로를 제작하였다. 강압 컨버터로 311V를 12V 로 출력하고 DC 전압 12V를 무선으로 연결하여 5V 충전 전압을 출력한다. 실험을 통해 스마트폰 무선 충전용 강압 컨버터의 유효성을 확인하였다.

• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.660-669
• /
• 2015

This paper presents a control scheme with a focus on the combination of phase disposition pulse width modulation (PDPWM) and DC capacitor voltage control for a chopper-cell based modular multilevel converter (MMC) for the purpose of eliminating the time-consuming voltage sorting algorithm and complex voltage balancing regulators. In this paper, the convergence of the DC capacitor voltages within one arm is realized by charging the minimum voltage module and discharging the maximum voltage module during each switching cycle with the assistances of MAX/MIN capacitor voltage detection and PDPWM signals exchanging. The process of voltage balancing control introduces no extra switching commutation, which is helpful in reducing power loss and improving system efficiency. Additionally, the proposed control scheme also possess the merit of a simple executing procedure in application. Simulation and experimental results indicates that the MMC circuit together with the proposed method functions very well in balancing the DC capacitor voltage and improving system efficiency even under transient states.

• 조명전기설비학회논문지
• /
• 제24권4호
• /
• pp.81-94
• /
• 2010

본 논문에서는 고효율 공진형 비대칭 하프브리지 플라이백컨버터가 제안된다. 컨버터의 1차측 하프브리지 회로는 공진커패시턴스와 변압기 누설인덕턴스를 이용하여 비대칭 펄스폭변조(PWM; Pulse-Width Modulation) 방식에 의한 소프트스위칭 형태로 동작한다. 그리고 컨버터 2차측의 플라이백 회로는 간단한 구동회로에 의해 새로운 전압구동방식으로 동작하는 동기정류기를 이용한다. 제안된 컨버터는 이렇게 하여 컨버터의 전체효율을 향상시킨다. 또한 본 논문에서는 제안된 컨버터의 동작원리를 모드별로 설명하고 컨버터 설계 시의 고려사항과 프로토타입 컨버터의 설계 예를 각각 제시한다. 그리고 본 논문에서 제안하는 전압구동방식으로 동작하는 동기정류기의 간단한 구동기법에 관하여 간략하게 설명한다. 설계된 프로토타입 컨버터는 광범위 입력전압(교류 $V_{in,rms}$=75~265[V])이 가능하며 5[V]의 직류 출력전압과 100[W]의 출력전력을 가진다. 제안된 컨버터의 우수한 성능을 입증하기 위하여 설계된 파라미터로써 프로토타입 컨버터를 제작하여 실험하였으며, 이를 통하여 제안된 컨버터의 우수한 성능을 보인다.

• 전기학회논문지P
• /
• 제51권3호
• /
• pp.120-125
• /
• 2002

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the switching-mode power converter, the output voltage is generally controlled by varying the duty ratio of main switch. When a converter operates in steady state, duty ratio of the converter is kept constant. So the power of switching noise is concentrated in specific frequencies. Generally, to reduce the EMI and improve the immunity of converter system, the switching frequency of converter needs to be properly modulated during a rectified line period instead of being kept constant. Random Pulse Width Modulation (RPWM) is performed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%~30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.163-172
• /
• 2016

The modular multilevel converter (MMC) has been receiving increased attentions in recent years. The new modular multilevel converter is a derivative topology from the traditional MMC in which the number of sub-modules (SMs) necessitated by each phase can be reduced by one. This paper presents a phase-shifted carrier pulse-width modulation (PSC-PWM) for the new MMC with an optimal phase-shifted angle to suppress the harmonics of the output voltage. Further, the harmonic features when the capacitor voltage of the middle SM is selected as two different values are also investigated. Moreover, in order to avoid introducing an unnecessary dc offset current at the ac terminals of the new MMC, a novel capacitor voltage balancing scheme is proposed by adjusting the amplitude of the reference signals rather than the offset. Finally, the validity and effectiveness of the proposed modulation and balancing schemes have been verified by experimental results based on a three-phase prototype of the new MMC.

• 조명전기설비학회논문지
• /
• 제20권4호
• /
• pp.21-28
• /
• 2006

본 논문에서는 Ballard사의 1.2[kW]급 연료전지와 연료전지의 저전압($28{\sim}43[VDC]$)을 승압(380([VDC])시키기 위한 풀-브리지 직류-직류 컨버터, 그리고 승압된 직류 링크전압을 교류 전압(220[VAC]), 60[Hz]으로 변환하기 위한 단상 풀-브리지 인버터로 구성된 연료전지 발전용 전력변환시스템 중 풀-브리지 고주파 절연형 영전압 영전류 스위칭 위상 천이 펄스폭 변조 직류-직류 컨버터를 제안하였다. 제안한 풀-브리지 고주파 절연형 영전압 영전류 스위칭 위상 천이 펄스폭 변조 직류-직류는 프리휠링 다이오드를 포함한 탭부 인덕터 필터를 이용하여 순환 전류를 저감시켰으며, 스위치 및 변압기의 턴-온, 턴-오프시에 오버슈트 전압이나 과도현상이 발생하지 않는다. 그리고 넓은 출력 전압 조정에도 효율을 $93{\sim}97[%]$정도 얻을 수 있으며, 출력 부하전류의 변화에 대해 거의 일정한 출력 전압 특성을 가졌다.

• Journal of Power Electronics
• /
• 제16권2호
• /
• pp.399-413
• /
• 2016

This paper presents a topology for a modular power electronic transformer (PET) and a control scheme. The proposed PET consists of a cascaded H-Bridge rectifier on the primary side, a high-frequency DC/DC conversion cell in the center, and a cascaded H-Bridge inverter on the secondary side. It is practical to use PETs in power systems to reduce the cost, weight and size. A detailed analysis of the structure is carried out by using equivalent circuit. An algorithm to control the voltages of each capacitor and to maintain the power flow in the PET is established. The merits are analyzed and verified in theory, including the bi-directional power flow, variable voltage/frequency and high power factor on the primary side. The experimental results validated the propose structure and algorithm.

• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.960-969
• /
• 2016

High-power three-level voltage-source converters are widely utilized in high-performance AC drive systems. In several ultra-power instances, the harmonics on the grid side should be reduced through multiple rectifications. A combined harmonic elimination method that includes a dual primary-side series-connected winding transformer and selective harmonic elimination pulse-width modulation is proposed to eliminate low-order current harmonics on the primary and secondary sides of transformers. Through an analysis of the harmonic influence caused by dead time and DC magnetic bias, a synthetic compensation control strategy is presented to minimize the grid-side harmonics in the dual primary side series-connected winding transformer application. Both simulation and experimental results demonstrate that the proposed control strategy can significantly reduce the converter input current harmonics and eliminates the DC magnetic bias in the transformer.