• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.171-175
• /
• 2011

In this paper, I have developed a high-speed and high-resolution measuring device in order to check the performance of drycell. The system is developed for the drycell manufacturing plant. Measuring time is one of key factors to inference on the production speed. So the developed system is designed to generate the classified result up to 1200ea/min. In the other words, each product can be classified within 25ms. There have been many studies to estimate both state of charge as well as state of health, such as OCV (Open Circuit Voltage), SC (Short Circuit) and measuring impedance with frequency pulse. But those methods take a few second due to surface discharge. To overcome the phenomenon, I developed the method to engage the reverse current to two electrodes of battery. As a result, I could achieve to measure the indigenous capacity without the problem of surface discharge.

• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.43-50
• /
• 2010

This paper proposes a new harmonic elimination PWM (HEPWM) scheme for voltage source inverters (VSI) based on the curve fittings of certain polynomials functions. The resulting equations to calculate the switching angle of the HEPWM require only the addition and multiplication processes; therefore any number of harmonics to be eliminated and the fundamental amplitude of the pole switching waveform (NP1) can be controlled on-line. An extensive angle error analysis is carried out to determine the accuracy of the algorithm in comparison to the exact solution. To verify the workability of the technique, an experimental single phase VSI is constructed. The algorithm is implemented on a VSI using a 16-bit microprocessor. The results obtained from the test rig are compared to the theoretical prediction and the results of the MATLAB simulations.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1694-1696
• /
• 2001

Partial discharge(PD) tests are used to evaluate the insulation condition of stator windings in six 6.6kV motors. These tests were conducted using a conventional partial discharge detector (PDD), turbine generator analyzer(TGA) and partial discharge analyzer(PDA). Off-line PD measurements were performed on six 6.6kV motors. PD magnitudes ranged from 740 pC to 5,100 pC at the normal line-to-ground voltage. Six 6.6kV motors have been equipped with eighteen 80pF epoxy-mica couplers(one per phase) on the motor terminal boxs. The PD pulse from sensors were measured with the TGA and PDA instruments on a normally operating motors. The PDD, TGA and PDA test results showed that internal discharge was detected in voids of the groundwall insulation.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.157-159
• /
• 1993

Recently, in the industrial applications, accurate arc control for welding machine are developed. This paper describes arc control of inverter-fed arc welding machine, and efficiency of inverter-fed arc welding machine. It is shown that the arc pressure and are stiffness of the pulse arc nay be as much as several times that of the equivalent dc are. Finally, the theoretical predictions are compared with test. The potential of such a welding machine is also described.

• Proceedings of the KIEE Conference
• /
• 2003.07e
• /
• pp.132-134
• /
• 2003

Insulator that is used in electric power equipment superannuation and being damaged disorder can. Such as defected insulator has repair or change must because defective influence in electrical equipment. There are many method developed for detecting the defected insulators, analyzed various test of devide voltage, electric field, ultrasonic and discharge pulse. But methods of detecting ultrasonic of discharge, electric field or leakage current could not application in the field, In this paper, we compare the advantage and the limitation of the method to detect defected insulator, and wish proposed using corona camera.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.3
• /
• pp.339-344
• /
• 2014

This paper presents a novel bipolar junction transistor (BJT) based electrostatic discharge (ESD) protection device. This protection device was designed for 20V power clamps and fabricated by a process with Bipolar-CMOS-DMOS (BCD) $0.18{\mu}m$. The current-voltage characteristics of this protection device was verified by the transmission line pulse (TLP) system and the DC BV characteristic was verified by using a semiconductor parameter analyzer. From the experimental results, the proposed device has a trigger voltage of 29.1V, holding voltage of 22.4V and low on-resistance of approximately $1.6{\Omega}$. In addition, the test of ESD robustness showed that the ESD successfully passed through human body model (HBM) 8kV. In this paper, the operational mechanism of this protection device was investigated by structural analysis of the proposed device. In addition, the proposed device were obtained as stack structures and verified.

• Proceedings of the KSMRM Conference
• /
• 2001.11a
• /
• pp.150-150
• /
• 2001

목적： 두 종류의 MR 기종에서 정상 성인의 두개 내 Frontal White Matter와 Basal Ganglia를 대상으로 서로 다른 TE에 대해 MR 분광법을 시행하여 기종 내, 기종간의 정상 값의 차이가 있는지 알아보았다. 대상 및 방법： 신경학, 형태학적으로 이상이 없는 8명의 자원자(평균나이 24세)를 대상으로 하였고 지원자 개개인에게 두 개의 서로 다른 1.5T MR 기종(A, B기종)에서 각각 TE를 달리하여 Frontal White Matter, Basal Ganglia를 대상으로 MR 분광법을 시행하였다. 사용한 pulse sequence는 PRESS 방법이며, TR/TE는 3000/22(25),136(144)msec, 선택체적의 크기는 20$\times$20$\times$20(mm$^3$)로 하였다. MR 기종 A는 manual prescan, B는 automatic prescan을 이용하여 최적의 분광정보를 얻었다. 각각의 MR장치에서 얻은 분광 데이터는 본 기관에서 제작된 S/W로 PC에서 처리하여 각 대사물질 피크 면적의 NAA/Cr, Cho/Cr값을 구하였고, TE값에 따라 MR 기종 내 및 기종간의 정상 값의 차이가 있는지 알아보기 위해 Faired-Comparison t-test(p<0.05)를 이용하여 분석하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.989-992
• /
• 1997

The objective of this study is to develop stencil cutting process and determine optimal conditions which make good-quality stencil by using a Nd:YAG laser. The effects of process parameters such as laser power, type of mask, gas pressure, cutting speed and pulse width on the cut edge quality were investigated. In order to analyze the cut surface characteristics(roughness, kerf width, dross) optical microscopy, SEM photography and roughness test were used. A a results, the optimal conditions of process parameters were determined, and the practical feasibility of the proposed system is also examined by using a commercial gerber file for PCB stencil manufacturing.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.3
• /
• pp.82-84
• /
• 2008

A surface encoder based on the Half-shaded square pattern (HSSP) is presented. The HSSP working as reference grid is composed of the straight lines which are easy to be fabricated and make measuring time short. Since the periodic cell is separated in ON/OFF by the $45^{\circ}$ straight line, the duration from the starting point of scanning to the first rising edge and the duty cycle of the pulse train vary with respect to the position of the starting point. And the relationship between X and Y position and the duration, and duty cycle is described in the simple linear equation. Therefore, it is possible to measure X and Y position with the measured duration and duty cycle without calculating load. Through the test set-up, the feasibility of the proposed surface encoder was verified. Also the future works for improvement of performance were suggested.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.52-55
• /
• 1999

다중 전송율(16, 24, 32, 40kbps)을 제공하는 G.726 부호화기는 ADPCM (Adaptive Differential Pulse Code Modulation) 부호화법을 사용한다. 본논문에서는 G.726 ADPCM 알고리즘을 C&S Technology에서 개발한 음성 신호 처리를 위한 범용 DSP인 CSD17C00A 칩을 이용하여 실시간 응용이 가능하도록 구현하였다. G.726에 대한 양방향 평가는 Codec Loopback test을 통해 수행되었으며, W-T에서 제공한 테스트 절차에 따라 평가되었다. 본 논문에서 구현된 G.726 부호화기는 평균 11 MIPS의 계산 속도를 갖고, 프로그램 메모리 크기는 2.8K Words이고, 데이터 메모리 크기는 550 Words 를 필요로 하였다.