• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.394-397
• /
• 2003

In this paper, we have proposed a clock recovery algorithm of OFDM/QPSK-DMR(Orthogonal Frequency Division Multiplexing/Quadrature Phase Shift Keying Modulation-Digital Microwave Radio)system using BL-PSF(Band Limited-Pulse Shaping Filter) and have analyzed the clock phase error variance performance of OFDM/QPSK and single carrier DMR systems. The existing OFDM/QPSK-DMR system using the windowing requires training sequence or CP(Cyclic Prefix) to synchronize a receiver clock frequency Because there is no training sequence or CP(Cyclic prefix) in our proposed DMR system, the proposed clock recovery algorithm is useful to the OFDM/QPSK-DMR system using BL-PSF, The simulation results confirm that the proposed clock recovery algorithm has the same clock phase error variance performance in a single carrier DMR system under AWGN(Additive White Gaussian Noise) environment.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.250-253
• /
• 2003

In this paper, a characteristics and points of Guassian pulse using UWB system is analyzed, the TDMG pulse is proposed that originated ultra wide band signal without pulse width reduction. It is showed that TDMG pulse character compare with Gaussian pulse through computer simulation. And it is verified that decreased a interference of other communication systems

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2086-2088
• /
• 2000

Key elements of in the development Electro-Thermal-Chemical propulsion (ETC) are high current pulse shaping, switching and storage bank device with high energy density 300kJ pulse power capacitor bank module for ETC application is designed and fabricated. The tested result are described.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.263-266
• /
• 2002

Many methods have been Proposed to reduce the PAPR of the OFDM signal. Among them a method that uses the time waveform of the different sub-carriers. The method is referred to as pulse shaping and it works with arbitrary number of sub-carriers and my type of base-band linear modulation. It has been shown, using this technique, that it is possible to design a set of time waveforms that reduce the PAPR of the OFDM transmitted signal and improve its power spectrum simultaneously. In this paper, we investigate the effect of some of these sets of time waveforms on the OFDM system performance in terms of Bit Error Rate (BER).

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.8
• /
• pp.1270-1278
• /
• 2004

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG laser welding. A large porosity was formed in a keyhole mode of deeply penetrated weld metal of any stainless steel. Solidification cracks were present in STS 310S with above 0.017%P and undercuts were formed in STS 303 with about 0.3%S. The conditions for the formation of porosity were determined in further detail in STS 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of STS 310S through a high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.784-790
• /
• 2012

In this paper, an all-digital CMOS ultra-wideband(UWB) pulse generator for high band(6~10 GHz) frequency range is presented. The pulse generator is designed and implemented with extremely low power and low complexity. It is designed to meet the FCC spectral mask requirement by using Gaussian pulse shaping circuit and control the center frequency by using CMOS delay line with shunt capacitor. Measurement results show that the center frequency can be controlled from 4.5 GHz to 7.5 GHz and pulse width is 1.5 ns and pulse amplitude is 310 mV peak to peak at 10 MHz pulse repetition frequency(PRF). The circuit is implemented in 0.13 um CMOS process with a core area of only $182{\times}65um^2$ and dissipates the average power of 11.4 mW at an output buffer with 1.5-V supply voltage. However, the core consumes only 0.26 mW except for output buffer.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.111-116
• /
• 2005

We propose a BASK (Binary Amplitude Shift Keying) system for Giga-bit Modem in millimeter band. The proposed system consists of a high speed shutter of the transmitter and a repeater of the receiver. The shutter of the proposed system is introduced for pulse shaping to improve the intersymbol interference (ISI). The repeater consists of several stage converters. A converter is constructed with a low pass filter and a limiter. The repeater can improve the signal-to-noise ratio (SNR) and make the rectangular pulse train. The proposed system is a simple system that uses conversion method without IF (Intermediate Frequency) process.

• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1637-1643
• /
• 2018

To reduce the laser pulse shape distortion accompanying the amplification process and achieve an intended output pulse shape in the Nd:YAG amplifier chain, we propose a frequency-modulated pulse-amplification method. Assuming carrier-frequency-modulated seed pulses, we numerically simulate the pulse amplification in an Nd:YAG amplifier chain where severe distortion occurs. For the calculation, we develop a modified Frantz-Nodvik equation, which enables two inputs with different carrier frequencies. The simulation results indicate that the temporal contrast of the seed pulse needed to obtain a flat output pulse shape is reduced by 16 - 25 dB when frequency modulation is applied.

• 전기의세계
• /
• v.29 no.5
• /
• pp.321-328
• /
• 1980

The Q-switching oscillator of TE $M_{00}$ mode was constructed in order to improve the properties of energy focusing and amplification, and prevent laser materials from breakdown. The Q-switching was done by means of electro-optical effect using Glan prism and KDP Pockels cell. Sharp laser pulse of risetime-1 ns and variable pulse width 2-10 ns was obtained from Q-switching laser pulse by PTM method using a laser triggered spark gap (LTSG), Glan prism and Pockels cell. A single ultra-short pulse (picosec order in pulse width) was obtained from mode-locked pulse train in combination of a mode-locked oscillator using saturable dye cell with pulse shaping system using PTM method.d.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.415-424
• /
• 2016

This paper describes a high data rate proximity transmitter design for high resolution smartphone-mirrored display applications. A 2 Gb/s transmitter is designed with a low transmission power of -70 dBm/MHz and a wide bandwidth of nearly 3 GHz. A digital pre-correction method is employed in the transmitter to mitigate the inter-symbol interference problem. A carrier-based digital pulse shaping and a reconfigurable digital envelope generation methods are employed for robust operation by utilizing 20 phases from a 2 GHz phase-locked loop. A 6.5-9.5 GHz transmitter implemented in 65 nm CMOS achieves the maximum data rate of 2 Gb/s, consuming only 7.6 mW from a 1 V supply.