• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.167-170
• /
• 2002

The design and fabrication of Q-band 3-stage monolithic microwave integrated circuit(MMIC) driver and power amplifiers for WLAN are presented using 0.2${\mu}{\textrm}{m}$ AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor(PHEMT). In each stage of the MMIC DA, a negative feedback is used for both broadband and good stability. The MMIC PA has employed a balanced configuration to overcome these difficulties and achieve high power with low VSWR over a wide frequency range. In the MMIC DA, the measurement results arc achieved as an input return loss under -4dB, an output return loss under -l0dB, a gain of 14dB, and a PldB of 17dB at C-band(36~ 44GHz). The chip size is 28mm$\times$1.3mm. The developed MMIC PA has the l0dB linear gain over 360Hz to 420Hz band and 22dBm PldB performance at 400Hz. The size of fabricated MMIC PA is 4mm x3mm. These results closely match with design results. This MMIC DA Sl PA will be used as the unit cells to develop millimeter-wave transmitters for use in wideband wireless LAN systems.

• ETRI Journal
• /
• v.36 no.2
• /
• pp.206-213
• /
• 2014

This paper presents a novel 90 GHz band 16-quadrature amplitude modulation (16-QAM) orthogonal frequency-division multiplexing (OFDM) communication system. The system can deliver 6 Gbps through six channels with a bandwidth of 3 GHz. Each channel occupies 500 MHz and delivers 1 Gbps using 16-QAM OFDM. To implement the system, a low-noise amplifier and an RF up/down conversion fourth-harmonically pumped mixer are implemented using a $0.1-{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor process. A polarization-division duplex architecture is used for full-duplex communication. In a digital modem, OFDM with 256-point fast Fourier transform and (255, 239) Reed-Solomon forward error correction codecs are used. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 19.8 dB.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1054-1057
• /
• 2002

The design and fabrication of Q-band 3-stage monolithic microwave integrated circuit(MMIC) amplifier for WLAN are presented using 0.2$\square$ AIGaAs/lnGaAs/GaAs pseudomorphic high electron mobility transistor (PHEMT). In each stage of the MMIC, a negative feedback is used for both broadband and good stability. The measurement results are achieved as an input return loss under -4dB, an output return loss under -10dB, a gain of 14dB, and a PldB of 17dBm at Q-band(36～44GHz). These results closely match with design results. The chip size is 2.8${\times}$1.3mm$^2$. This MMIC amplifier will be used as the unit cell to develop millimeter-wave transmitters for use in wideband wireless LAN systems.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.649-654
• /
• 2012

This paper presents a novel 16-quadrature-amplitude-modulation (QAM) E-band communication system. The system can deliver 10 Gbps through eight channels with a bandwidth of 5 GHz (71-76 GHz/81-86 GHz). Each channel occupies 390 MHz and delivers 1.25 Gbps using a 16-QAM. Thus, this system can achieve a bandwidth efficiency of 3.2 bit/s/Hz. To implement the system, a driver amplifier and an RF up-/down-conversion mixer are implemented using a $0.1{\mu}m$ gallium arsenide pseudomorphic high-electron-mobility transistor (GaAs pHEMT) process. A single-IF architecture is chosen for the RF receiver. In the digital modem, 24 square root raised cosine filters and four (255, 239) Reed-Solomon forward error correction codecs are used in parallel. The modem can compensate for a carrier-frequency offset of up to 50 ppm and a symbol rate offset of up to 1 ppm. Experiment results show that the system can achieve a bit error rate of $10^{-5}$ at a signal-to-noise ratio of about 21.5 dB.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.213-217
• /
• 2001

본 논문에서는 CPW 구조를 이용하여 60 GHz 무선 시스템 응용을 위한 V-band용 하향 주파수 혼합기를 설계 및 제작하였다. 하향 주파수 혼합기의 설계 및 제작에 있어서 GaAs PHEMT(Pseudomorphic high electron mobility transistor)를 기반으로 하였으며, 회로설계를 위해 coplanar waveguide(CPW) 라이브러리를 구축하여 이용하였다. 제작된 하향 주파수 혼합기의 변환이득은 국부발진주파수(LO) 입력이 8 dBm일 때 -8.5 dB의 최대 변환이득 특성을 얻었으며 Pl dB는 -3.3 dBm을 얻었다. 제작된 회로의 칩 크기는 1.6$\times$l.6 $\textrm{mm}^2$ 이다.

• ETRI Journal
• /
• v.46 no.2
• /
• pp.323-332
• /
• 2024

Receiver and transmitter monolithic microwave integrated circuit (MMIC) multifunction chips (MFCs) for active phased-array antennas for Ka-band satellite communication (SATCOM) terminals have been designed and fabricated using a 0.15-㎛ GaAs pseudomorphic high-electron mobility transistor (pHEMT) process. The MFCs consist of four-channel radio frequency (RF) paths and a 4:1 combiner. Each channel provides several functions such as signal amplification, 6-bit phase shifting, and 5-bit attenuation with a 44-bit serial-to-parallel converter (SPC). RF pads are implemented on the bottom side of the chip to remove the parasitic inductance induced by wire bonding. The area of the fabricated chips is 5.2 mm × 4.2 mm. The receiver chip exhibits a gain of 18 dB and a noise figure of 2.0 dB over a frequency range from 17 GHz to 21 GHz with a low direct current (DC) power of 0.36 W. The transmitter chip provides a gain of 20 dB and a 1-dB gain compression point (P1dB) of 18.4 dBm over a frequency range from 28 GHz to 31 GHz with a low DC power of 0.85 W. The P1dB can be increased to 20.6 dBm at a higher bias of +4.5 V.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.583-586
• /
• 2005

In this paper, millimeter-wave monolithic integrated circuit (MIMIC) low noise amplifier (LNA) for V-band, which is applicable to 58 GHz, we designed and fabricated. We fabricated the module using the fabricated LNA chips. The V-band MIMIC LNA was fabricated using the high performance $0.1\;{\mu}\;m$ ${\Gamma}-gate$ pseudomorphic high electron mobility transistor (PHEMT). The MIMIC LNA was designed using active and passive device library, which is composed $0.1\;{\mu}\;m$ ${\Gamma}-gate$ PHEMT and coplanar waveguide (CPW) technology. The designed V-band MIMIC LNA was fabricated using integrated unit processes of active and passive device. Also we fabricated CPW-to-waveguide fin-line transition of WR-15 type for module. The Transmission Line was fabricated using RT Duroid 5880 substrate. The measured results of V-band MIMIC LNA and Module are shown $S_{21}$ gain of 13.1 dB and 8.3 dB at 58 GHz, respectively. The fabricated LNA chip and Module in this work show a good noise figure of 3.6 dB and 5.6 dB at 58 GHz, respectively.

• ETRI Journal
• /
• v.27 no.3
• /
• pp.304-311
• /
• 2005

We report on the fabrication of an AlGaAs/InGaAs/GaAs pseudomorphic high electron mobility transistor (PHEMT) using a dielectric-defined process. This process was utilized to fabricate $0.12\;{\mu}m\;{\times}\;100 {\mu}m$ T-gate PHEMTs. A two-step etch process was performed to define the gate footprint in the $SiN_x$. The $SiN_x$ was etched either by dry etching alone or using a combination of wet and dry etching. The gate recessing was done in three steps: a wet etching for removal of the damaged surface layer, a dry etching for the narrow recess, and wet etching. A structure for the top of the T-gate consisting of a wide head part and a narrow lower layer part has been employed, taking advantage of the large cross-sectional area of the gate and its mechanically stable structure. From s-parameter data of up to 50 GHz, an extrapolated cut-off frequency of as high as 104 GHz was obtained. When comparing sample C (combination of wet and dry etching for the $SiN_x$) with sample A (dry etching for the $SiN_x$), we observed an 62.5% increase of the cut-off frequency. This is believed to be due to considerable decreases of the gate-source and gate-drain capacitances. This improvement in RF performance can be understood in terms of the decrease in parasitic capacitances, which is due to the use of the dielectric and the gate recess etching method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3917-3922
• /
• 2010

In this paper, 3 stage amplifier MMIC was designed and fabricated with U-band optimized epitaxal pHEMT that produced by large signal characterization and modeling for 60 GHz band. The pHEMT used in this paper, the gate $0.12\;{\mu}m$ length and total gate width of $100\;{\mu}m$, $200\;{\mu}m$ has been modeled using the large signal designed with negative feedback and MCLF instead of MIM capacitor for improving stability. Fabricated MMIC $2.5{\times}1.5mm^2$ size, current about 40 mA, operating frequency 59.5~60.5 GHz, gain 19.9~18.6 dB, input matching characteristics -14.6~-14.7 dB, output matching characteristics -11.9~-16.3 dB and output -5 dBm characteristics were obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.766-772
• /
• 2018

A 6~10 GHz wide-band power amplifier was designed using an InGaAs enhancement-mode(E-mode) $0.15{\mu}m$ pseudomorphic high-electron-mobility transistor(pHEMT). The positive gate bias of the E-mode pHEMT device removes the need for complex negative voltage generation circuits, therefore reducing the module size. The wire bond and substrate loss parameters were modeled and extracted using a three-dimensional electromagnetic(3D EM) simulation. For wideband characteristics, lossy matching was adopted and the gate bias was optimized for maximum power and efficiency. The measured gain, in/output return loss, output power, and power-added efficiency were greater than 20 dB, 8 dB, 27 dBm, and 35 %, respectively, in the 6~10 GHz band.