• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.19-28
• /
• 2000

In general the data such as thrust, pressure, temperature and combustion time are measured in developing the propulsion system of solid rocket motor through static firing test. But in the case of personal surface to air missile there are required a severe safety specifications in order to eliminate gunner hazard from the exhaust plume of motors. The safety requirements lead to the design of separation device and safety igniter device. The dynamic firing test for the designed two devices should be conducted under the flight environmental conditions to verify the requirements compliance. In this study the technique for dynamic firing test of propulsion system of personal surface to air missile is proposed and the method to design the dynamic test bench is also studied.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.548-553
• /
• 2011

The device for studying combustion characteristic of aluminum powder and water was developed. The device has ability to adjust temperature, pressure, and equivalent ratio to some specified value which effect on combustion characteristic of aluminum and water mixture. Methane combustor, water supply device, aluminum powder feeder, and linear combustor are assembled to aluminum combustion test device. Each device has the ability to supply matter to combustor on steady and quantitatively controlled manner and test sequence specified by user can be automatically controlled. The combustion of aluminum powder was observed when integrated device was operated normally.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.146-154
• /
• 2004

In this study, numerical analysis has been performed to investigate the flow characteristics of a drag improvement device which is designed to achieve accurate impact point. The drag increase due to drag improvement device has been analyzed. And the effect of spread angle and location of drag improvement device has also been investigated. The drag improvement device with 20 degree spread angle increased the drag 3.5 times. The corresponding weight of the device is found out to be 26g.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.79-82
• /
• 2011

An afterburning device was developed to safely treat unburnt gases of fuel-rich condition discharged by a gas generator. Hot-firing tests for a subscale gas generator were carried out to investigate operation and safety of the afterburning device. When supplying additional liquid oxygen, the length of the afterburning flame was significantly reduced.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.3
• /
• pp.100-107
• /
• 2001

Miro propulsion device is a literally very small propulsion system The reason why such a small propulsion system is required is that micro satellites are considered as substitutions for conventional satellites to reduce cost; the fabrication of micro satellites enables us to produce mass production Microrockets have relatively high values of thrust/weight ratio due to the cube law; weight is proportional to volume and thrust is proportional to area. Accordingly, downsizing makes the ratio of thrust/weight ratio high However, conventionally ignorable facts are not negligible any more in small scale systems. for chemical micro rockets, downsizing causes lots of heat loss as surface to volume ratio increases, which results in the destruction of radical ions. For thrusters using plasma, the generation of strong magnetic field for plasma is very difficult. Also, in the aspect of flow dynamics, the effects of drag and viscosity are important parameters in low Re flows. When these problems are solved, micro propulsion systems can be commercialized and result in spin-off effects in many fields.

• Journal of Drive and Control
• /
• v.18 no.4
• /
• pp.43-51
• /
• 2021

In this study, we designed a hydraulic propulsion propeller system that allows dredged materials to be carried out by the dredger to the disposal place. The proposed model equation was used to formulate the screw propeller specifications considering the resistance to the dredger, and the quantitative specifications of the hydraulic propulsion propeller were determined through the numerical analysis programs. In addition, based on the proposed results, we were able to determine the specifications of the hydraulic system that was used for the hydraulic motor in the propulsion propeller device and then manufactured the hydraulic propulsion propeller. To guarantee the reliability of the proposed model equation, an external testing agency was invited and verified that the hydraulic propulsion propeller based on the proposed model equation could achieve the target speed in the dredger.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1192-1195
• /
• 2017

This paper describes the heat resistance characteristics of the imaging device installed in behind the engine due to monitoring the engine condition, and this paper includes the introduction and development of the imaging probe. Because the imaging device which is at the rear end of the engine is exposed to a high temperature and high pressure, the stability of the device should be secured by changing the device shape and supplying cooling water. The imaging probe in ADD engine test facility is installed at the rear end of the engine, and it is designed by reflecting the heat resistance characteristics to ensure the stability of the device.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.2
• /
• pp.390-398
• /
• 2015

Energy-saving devices for 317K VLCC have been developed from a propulsion standpoint. Two ESD candidates were designed via computational tools. The first device WAFon composes of flow-control fins adapted for the ship wake to reduce the loss of rotational energy. The other is WAFon-D, which is a WAFon with a duct to obtain additional thrust and to distribute the inflow velocity on the propeller plane uniform. After selecting the candidates from the computed results, the speed performances were validated with model-tests. The hydrodynamic characteristics of the ESDs may be found in improved hull and propulsive efficiencies through increased wake fraction.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.142-148
• /
• 2018

To improve the performance of a launch vehicle, kerosene, a launch vehicle fuel, undergoes a densification process. Liquid nitrogen injection cooling is an effective densification method which has a simple system and is inexpensive. During the cooling process, however, nitrogen may dissolve in the kerosene, possibly resulting in changes to fuel properties. Therefore, it is essential to measure and eliminate the amount of dissolved nitrogen in the kerosene. In this study, the vacuum extraction principle is introduced to measure the content of dissolved nitrogen in the kerosene. In addition, the experimental results, which used a designed/manufactured nitrogen sampling device, are described. From the results, the validity of the nitrogen sampling device and the dissolved nitrogen measurement/elimination methods was demonstrated.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.665-670
• /
• 2005

This paper introduces the propulsion system(Motor Block) stabilization test result for Korean High Speed Railway(HSR). The developed propulsion system using high power semiconductor, IGCT(Integrated Gate Commutated Thyristor) consists of two PWM converter and VVVF inverter. In this paper, overall configuration of propulsion system is briefly described and stabilization tests are made to verify the developed propulsion system. The presented test results shows beatless control method of inverter output current at the 200km/h and performance test of BCH.