• 한국재료학회지
• /
• 제27권1호
• /
• pp.12-18
• /
• 2017

Transparent organic-inorganic hybrid hard coating films were prepared by the addition of $SiO_2$ or $ZrO_2$, as an inorganic filler to improve the hardness property, filler was highly dispersed in the acrylic resin. To improve the compatibility in the acrylic resin, $SiO_2$ or $ZrO_2$ is surface-modified using various silanes with variation of the modification time and silane content. Depending on the content and kind of the modified inorganic oxide, transparent modified inorganic sols were formulated in acryl resin. Then, the sols were bar coated and cured on PET films to investigate the optical and mechanical properties. The optimized film, which has a modified $ZrO_2$ content of 4 wt% markedly improved in terms of the hardness, haze, and transparency as compared to neat acrylate resin and acrylate resin containing modified $SiO_2$ content of 8 wt%. Meanwhile, the low transparency and high haze of these films slowly appeared at $SiO_2$ content above 10 wt% and $ZrO_2$ content of 5 wt%, but the hardness values were maintained at 2H and 3H, respectively, in comparison with the HB of neat acrylate resin.

• 소성∙가공
• /
• 제11권8호
• /
• pp.682-690
• /
• 2002

The formation of adiabatic shearband in tungsten heavy alloys(WHA) was studied in this investigation. Five prismatic specimens were loaded by high velocity impacts and treated as plane strain problems. To find out the effect of particle's volume ratio, specimens containing 81%, 93% and 97% volume percents of tungsten particles were used. Also the effects of particle's geometry and size on the formation of shearband were studied for 81% volume percent alloys by small size particle model, large size particle model and undulated particle models, and the results were discussed.be used to diagnose the causes of necking and fracture in industrial practice and to investigate whether these defects were caused by material property variation, changes in lubrication, or incorrect press settings. In non-axisymmetric deep drawing, three modes of forming regimes are found: draw, stretch, plane strain. The stretch mode for non-axisymmetric deep drawing could be defined when the major and minor strains are positive. The draw mode could be defined when the major strain is positive and minor strain is negative, and plane strain mode could be defined when the major strain is positive and minor strain is zero. Through experiments the draw mode was shown on the wall and flange are one of a drawn cup, while the plane strain and the stretch mode were on the punch head and the punch corner area respectively, We observed that the punch load of elliptical deep drawing was decreased according to increase of die corner radius and the thickness deformation of minor side was more large than major side.

• 한국식품과학회지
• /
• 제27권4호
• /
• pp.571-575
• /
• 1995

피부조직 콜라겐의 열안정성에 대한 기초자료를 얻고자 DSC를 이용하여 Tm(transition temperature)와 ${\Delta}H(enthalpy)$를 측정하였다. 수화시간과 수화율에 따른 불용성 콜라겐의 DSC 특성은 수화시간에 비하여 수화율이 콜라겐 구조안정성에 미치는 영향이 큰 것으로 나타났으며, 수화율이 증가할수록 Tm은 낮아지고 ${\Delta}H$는 증가하였다. 주령 및 성별에 따른 acetone dried skin의 Tm 및 ΔH는 암컷의 경우보다 수컷의 경우가 다소 높았으며, 주령이 증가할수록 Tm과 ${\Delta}H$가 서서히 증가하고 있어 열안정성은 나이와 관계가 있음을 보여주었다. Acetone dried skin의 경우와는 달리 염가용성 콜라겐의 DSC 특성값은 암컷의 경우가 수컷의 경우보다 다소 높았으며, 암컷의 Tm과 ${\Delta}H$는 주령의 증가에 따라 유의적으로 감소하는 경향을 보였다. 이러한 결과는 피부조직내에서의 콜라겐 구조는 성별 또는 주령에 따라 달리 변화되고 있음을 간접적으로 시사한 것으로 생각되었다.

• 대한전자공학회논문지TC
• /
• 제45권4호
• /
• pp.22-30
• /
• 2008

본 논문은 웨이브릿 변환을 이용하여 사전정보 없이 입사하는 디지털 신호의 변조타입 자동식별 방법에 관한 것이다. 변조인식에 사용되는 특징(key features)은 변조타입에 대한 민감도가 우수하고, SNR에 대한 변화가 적은 속성을 가져야 한다. 잡음에 대한 변화가 적은 속성을 가진 웨이브릿 변환 계수에서 변조인식을 위해 4개의 특징(key features)을 선정하였다. 또한 선정된 특징들을 이용하여 총 8종의 디지털변조 신호를 분류하기 위해 시뮬레이션을 수행하였다. 소프트웨어 라디오의 변조인식 모듈 탑재를 고려하여, 3 타입의 변조인식기에 대한 인식 정확도 및 수행시간을 비교 분석하였다. 시뮬레이션 결과 전체 인식시간은 MDC(Minimum Distance Classifier)와 DTC(Decision Tree Classifier)가 빠르게 수행되었고, 인식정확도는 MDC와 SVMC(Support Vector Machine Classifier)가 우수하게 제시되었다.

• 전자공학회논문지
• /
• 제50권11호
• /
• pp.219-225
• /
• 2013

본 논문은 소노스(SONOS) 형태의 타원형 게이트 올 어라운드(GAA) 구조를 갖는 플레쉬 셀의 프로그램과 삭제 특성을 채널의 이심률 변화에 대해 연구 하였다. 타원형 GAA SONOS 셀의 쓰기와 삭제에 대한 해석적 모델을 제안하고 평가하였다. 점진적 계단형 펄스 프로그램(ISPP)시 타원의 이심률이 증가할수록 인가 전압에 대해 문턱전압이 비선형적으로 변화한다. 이는 2차원 소노스 구조나 원형 3차원 GAA 구조에서 선형적 특성을 보이는 것과는 매우 다른 모습이다. ISPP 특성에 대한 모사의 결과는 실험적 결과와 잘 부합됨을 발견할 수 있다.

• 한국지열·수열에너지학회논문집
• /
• 제8권2호
• /
• pp.36-47
• /
• 2012

Time-series variation of groundwater temperature in Mongolia shows that maximum temperature is occured from end of October to the first of February(winter time) and minimum temperature is observed from end of April to the first of May(summer time). Therefore ground temperature is s a good source for space heating in winter and cooling in summer. Groundwater temperatures monitored from 3 alluvial wells in Ulaabaatar at depth between 20 and 24 m are $(4.43{\pm}0.8)^{\circ}C$ with average of $4.21^{\circ}C$ but mean annual ground temperature(MAGT) at the depth of 100 m in Ulaanbaatar was about $3.5{\sim}6.0^{\circ}C$. Bore hole length required to extract 1 RT's heat energy from ground in heating time and to reject 1 RT's heat energy to ground in summer time are estimated about 130 m and 98 m respectively. But in case that thermally enhanced backfill and U tube pipe placement along the wall are used, the length can be reduced about 25%. Due to low MAGT of Ulaabaatar such as $6^{\circ}C$, the required length of GHX in summer cooling time is less than the one of winter heating time. Mongolia has enough available property, therefore the most cost effective option for supplying a heating energy in winter will be horizontal GHX which absorbs solar energy during summer time. It can supply 1 RT's ground heat energy by 570 m long horizontally installed GHX.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.239-242
• /
• 1998

Ca $F_2$ films have superior gate insulator properties than conventional gate insulator such as $SiO_2$, Si $N_{x}$, $SiO_{x}$, and T $a_2$ $O_{5}$ to the side of lattice mismatch between Si substrate and interface trap charge density( $D_{it}$). Therefore, this material is enable to apply Thin Film Transistor(TFT) gate insulator. Most of gate oxide film have exhibited problems on high trap charge density, interface state in corporation with O-H bond created by mobile hydrogen and oxygen atom. This paper performed Ca $F_2$ property evaluation as MIM, MIS device fabrication. Ca $F_2$ films were deposited at the various substrate temperature using a thermal evaporation. Ca $F_2$ films was grown as polycrystalline film and showed grain size variation as a function of substrate temperature and RTA post-annealing treatment. C-V, I-V results exhibit almost low $D_{it}$(1.8$\times$10$^{11}$ $cm^{-1}$ /le $V^{-1}$ ) and higher $E_{br}$ (>0.87MV/cm) than reported that formerly. Structural analysis indicate that low $D_{it}$ and high $E_{br}$ were caused by low lattice mismatch(6%) and crystal growth direction. Ca $F_2$ as a gate insulator of TFT are presented in this paper paperaper

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.9-13
• /
• 2014

Effects of neutron irradiation on the superconducting properties of the undoped $MgB_2$ and the carbon(C)-doped $MgB_2$ bulk superconductors, prepared by an in situ reaction process using Mg and B powder, were investigated. The prepared $MgB_2$ samples were neutron-irradiated at the neutron fluence of $10^{16}-10^{18}n/cm^2$ in a Hanaro nuclear reactor of KAERI involving both fast and thermal neutron. The magnetic moment-temperature (M-T) and magnetization-magnetic field (M-H) curves before/after irradiation were obtained using magnetic property measurement system (MPMS). The superconducting critical temperature ($T_c$) and transition width were estimated from the M-T curves and critical current density ($J_c$) was estimated from the M-H curves using a Bean's critical model. The $T_cs$ of the undoped $MgB_2$ and C-doped $MgB_2$ before irradiation were 36.9-37.0 K and 36.6-36.8 K, respectively. The $T_cs$ decreased to 33.2 K and 31.6 K, respectively after irradiation at neutron fluence of $7.16{\times}10^{17}n/cm^2$, and decreased to 22.6 K and 24.0 K, respectively, at $3.13{\times}10^{18}n/cm^2$. The $J_c$ cross-over was observed at the high magnetic field of 5.2 T for the undoped $MgB_2$ irradiated at $7.16{\times}10^{17}n/cm^2$. The $T_c$ and $J_c$ variation after the neutron irradiation at various neutron fluences were explained in terms of the defect formation in the superconducting matrix by neutron irradiation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.774-779
• /
• 2016

본 연구에서는 선박의 곡 외판 구조에 TMCP 강재의 사용 범위 확대 가능성을 연구하고자 노말라이징강 및 TMCP 강 DH32 재질 강재에 선상가열 후 기계적 물성 시험을 실시하여 DNV 선급 및 IACS 규정의 품질 요구 기준에 적합한지 연구하였다. TMCP강재 인장시험에서 요구기준 YS = 315 MPa 대비 385 Mpa로서 약 18% 높게 나타났고, TS = 440 ~ 570 MPa 기준 대비 525 MPa로 요구 기준에 적합하였다. 샤르피 V-노치 $-20^{\circ}C$ 충격시험에서도 요구 기준에 적합하였으며 경도시험에서 평균 T : 216, L : 275로서 규정인 Hv10 = 130 ~320 범위에 만족 하였다.

• 한국생산제조학회지
• /
• 제19권4호
• /
• pp.529-538
• /
• 2010

This paper presents a reliability-based topology optimization (RBTO) based on bidirectional evolutionary structural optimization (BESO). In design of a structure, uncertain conditions such as material property, operational load and dimensional variation should be considered. Deterministic topology optimization (DTO) is performed without considering the uncertainties related to the design variables. However, the RBTO can consider the uncertainty variables because it can deal with the probabilistic constraints. The reliability index approach (RIA) and the performance measure approach (PMA) are adopted to evaluate the probabilistic constraints in this study. In order to apply the BESO to the RBTO, sensitivity number for each element is defined as the change in the reliability index of the structure due to removal of each element. Smoothing scheme is also used to eliminate checkerboard patterns in topology optimization. The limit state indicates the margin of safety between the resistance (constraints) and the load of structures. The limit State function expresses to evaluate reliability index from finite element analysis. Numerical examples are presented to compare each optimal topology obtained from RBTO and DTO each other. It is verified that the RBTO based on BESO can be effectively performed from the results.