• Journal of the Korean GEO-environmental Society
• /
• v.15 no.2
• /
• pp.75-82
• /
• 2014

Recently, public works becoming bigger in Jeju are implemented various kinds of ground reinforcement method including the chemical grouting method. In this study, we have been investigated on the proper material and the injection condition for the excellent injection effect and the excellent strength of injection material and the permanent waterproof and reinforcement through the experiment. The kind of injection material has been selected through the uniaxial compression test and the endurance test of injection material as the chamber test. An experiment was performed with model ground made of scoria, the injection performance of selected material has been identified through the evaluation test of injection range using the decision test of injection amount and the calibration chamber test. As a result of test, it has been analyzed that MSG appeared to have the excellent strength, durability and injection performance all compared with the ordinary cement, this result is judged to be possible as the ancillary data of design at time of design and construction with the chemical grouting method in the future.

• Journal of Radiation Industry
• /
• v.6 no.1
• /
• pp.31-40
• /
• 2012

There are two methods to fabricate the readout electronic to a large-area CMOS image sensor (LACIS). One is to design and manufacture the sensor part and signal processing electronics in a single chip and the other is to integrate both parts with bump bonding or wire bonding after manufacturing both parts separately. The latter method has an advantage of the high yield because the optimized and specialized fabrication process can be chosen in designing and manufacturing each part. In this paper, LACIS chip, that is optimized design for the latter method of fabrication, is presented. The LACIS chip consists of a 3-TR pixel photodiode array, row driver (or called as a gate driver) circuit, and bonding pads to the external readout ICs. Among 4 types of the photodiode structure available in a standard CMOS process, $N_{photo}/P_{epi}$ type photodiode showed the highest quantum efficiency in the simulation study, though it requires one additional mask to control the doping concentration of $N_{photo}$ layer. The optimized channel widths and lengths of 3 pixel transistors are also determined by simulation. The select transistor is not significantly affected by channel length and width. But source follower transistor is strongly influenced by length and width. In row driver, to reduce signal time delay by high capacitance at output node, three stage inverter drivers are used. And channel width of the inverter driver increases gradually in each step. The sensor has very long metal wire that is about 170 mm. The repeater consisted of inverters is applied proper amount of pixel rows. It can help to reduce the long metal-line delay.

• Journal of agriculture & life science
• /
• v.43 no.2
• /
• pp.47-53
• /
• 2009

This research is intended to study the induction net of chrysanthemum used in its greenhouse and requiring lots of time for manual work and review the structural safety of a bed and existing greenhouses after designing the bed of a net which increases cropping period by sharply reducing the time of work and provides the bed of induction nets for cultivating chrysanthemum with its existing and new greenhouse. The review of sectional and biodynamic properties in 15 kinds of materials has revealed that the pipes of ${\phi}38.1{\times}1.7t$and ${\phi}38.1{\times}2.0t$ didn't exceed stress ratio but did 10mm drooping allowance. For this reason, the pipe of ${\phi}48.1{\times}1.5t$ net both stress ratio and drooping allowance. For the safety, the middle chamber should be designed into Truss type owing to bed load, wind load, and snow load when the bed of an induction net is installed in the middle chamber. When installing the middle chamber with a truss type, the greenhouse of chrysanthemum in Geochang area needs proper reinforcements because the stress in colullllls and wind proof walls exceeds stress allowance regardless of the installation of a bed.

• Journal of vocational education research
• /
• v.29 no.3
• /
• pp.247-263
• /
• 2010

The purpose of this study is making the career education program related to the subject, Manual Training and Home Economics, to present the effective guidance and to improve career maturity of students about the unit, "Making a choice of career and Job ethics" of middle school senior's course. In order to estimate this program, 60 students of 2 classes were chosen as research subjects among middle school seniors and each of classes was divided into two groups, an experimental group and a control group. After the experimental group was trained the career education program related to Manual Training and Home Economics for 15 sessions, the effect was verified by comparing tests before and after program execution. In order to prove effects of the program. Each grade of both the experimental group and the control group was taken analysis of covariance (ANCOVA). Result of the program experiment is following. First, after executing the career education program related to Manual Training and Home Economics to the experimental group, participants showed that both attitude and ability for career maturity were improved in each sub-factor field of the career maturity as a result of tests before and after program execution. Second, in program satisfaction estimation, most of students had a positive attitude and in every time satisfaction, they made high estimation on the program, especially including the proper level of students and interesting activities. Finally, the final program was completed based on the result of effect analysis of the program.

• Journal of Aerospace System Engineering
• /
• v.13 no.3
• /
• pp.78-86
• /
• 2019

This paper describes the stiffness optimization of the torsion spring hinge of the large SAR antenna considering the deployment performance. A large SAR antenna is folded in a launch environment and then unfolded when performing a mission in orbit. Under these conditions, it is very important to find the proper stiffness of the torsion spring hinge so that the antenna panels can be deployed with minimal impact in a given time. If the torsion spring stiffness is high, a large impact load at the time of full deployment damages the structure. If it is weak, it cannot guarantee full deployment due to the deployment resistance. A multi-body dynamics analysis model was developed to solve this problem using RecurDyn and the development performance were predicted in terms of: development time, latching force, and torque margin through deployment analysis. In order to find the optimum torsion spring stiffness, the deployment performance was approximated by the response surface method (RSM) and the optimal design was performed to derive the appropriate stiffness value of the rotating springs.

• The Journal of Sustainable Design and Educational Environment Research
• /
• v.18 no.1
• /
• pp.27-37
• /
• 2019

This study investigated and analyzed the rise and fall trend of enrolled students during the recent 30 years with the subject of 607 elementary schools in 11 Education Support Centers (25 Gu-districts) in Seoul to provide the basic data related to establishing the school accommodation plan of the Seoul Education Office. In particular, the study focuses on the 53 small schools in Seoul and examines whether a correlation exists between the 8 factors of the school accommodation plan and the increasing and decreasing of enrolled student numbers. First, 'school establishment policy' should not be a short-term therapy but a long-term and predictable sustainable policy. Second, among the eight factors, there seems to be a very high correlation between the 'aged low-rise house districts' and 'spatially isolated areas'. Third, 'close-packed apartment complexes' and 'rental apartment complexes' are also highly correlated. Fourth, the planning factors such as 'joint school districts, the reconstruction of apartment complexes and the connection to commercial districts' seem to be correlated to some degree. Therefore, further studies are needed to overcome these problems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.677-685
• /
• 2018

In construction, schedule management is the basic but important step, for the effective schedule management, the preparation of the reasonable schedule table should be prioritized. In the design stage, the optimal construction period can be selected through comparison of various conditions and construction methods considering weather conditions and site characteristics. But, At the planning phase, it is difficult to select the effective method and calculate the proper construction period by the basic data(D/B) analysis. In this paper, the construction method considering characteristics of each type and conditions of existing city was selected. For the reasonable duration calculation, we analyzed the unit schedule for RC method for open type and Shield TBM method for tunnel type. The normal project duration of construction assuming of 1,200m of extension and every 200m of ventilation was prepared by integrating each unit schedule. It was analyzed that it took 893 days for the open type and 616 days for the tunnel type. The results of this study will help to make type selection and normal project duration more easily in the planning phase. If it is linked to the design stage, it will be easy to estimate the process and construction cost.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.5
• /
• pp.65-71
• /
• 2003

In this paper, bending capacities of glulams with different configurations of cross-section were evaluated. These configurations included horizontal(BH), vertical(BVN), vertical with vertical plywood (BVV) and vertical combination of lamination with horizontal plywood(BVH). Full-scale bending tests were performed to investigate the effect of different section configurations on bending strength(MOR) and stiffness(MOE) of glulam. Compared with type BH, MOR of glulam with type BVN configuration was improved about 23%, which was considered to be caused by defect dispersion effect, while MOE of glulams with these two types of configurations were similar. Because MOE of plywood is generally smaller than that of solid wood laminar, MOE of type BVH glulam decreased about 15%, but in the case of type BVV glulam, MOR was improved without any reduction of MOE. The reason of this result could be undersood in the view of shear-reinforcement effect, which was verified from analysis of fracture mode. From the results of this study, it was concluded that bending capacity of glulam could be improved by proper section design, such as laminar arrangement and shear reinforcement.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.41-53
• /
• 1994

A SGTR accident postulated at Kori unit 1 is simulated with Mihama unit experience, which occurred on February 1991, to evaluate the capability of plant to cope with the transient. The system design and plant conditions of Kori Unit 1 are much similar with those of Mihama Unit 2. Therefore, special concern has been given to evaluate the sequence and the resulting consequence of the postulated SGTR accident at the Kori unit 1 An analysis is peformed as realistically as possible, with following the EOP of Kori unit 1. The result indicates that the leak through tube break terminates within about forty minutes, and the Kori unit 1 may be sufficient to cope with SGTR accident with same type of sequence. However, the reconsideration may be required for the design of Kori unit 1 which disconnects non-safety AC power from off-site power on SI signal generation. It may be pointed out that the content of EOP for SGTR accident is not enough to require operator's proper judgements. An analysis of SGTR accident tested in the LSTF which simulated the SGTR accident at the Mihama Unit 2 is peformed using the RELAP5/MOD3. The results indicates that the code yields in general good agreement with the test, except the break flowrate at the early stage of the event.

• Korea Science and Art Forum
• /
• v.19
• /
• pp.659-668
• /
• 2015

The Korean education program and environment do not meet the increasing demand of daycare by facility, manpower, and budget deficits although Korea has also been interested in the convergent human resource with integrated ideas by creative education since the introduction of the Nuri curriculum for 5 year old children in 2011. Thus, the purpose of this study is to establish the preschool education program and design the proper space for developing the creativity of children. The procedure of this study is as follows. First, this study proposes the direction for establishing the daycare programs after examining the existing Korean daycare facilities and programs based on documented references about designs for daycare facilities. Second, this study proposes the program plans based on the framework establishment for developing preschool education programs by combination of 5 types of children's behavior on play and 5 types of formative principles for creative education with play. Third, this study proposes the direction of designs and conditions of daycare facilities for effectively managing the programs previously mentioned. As a result of theprocedure, this study comprehensively delineates the education program models and space plans for developing the creativity of Korean children, and suggests the necessity of development model of continuous education program by establishment of frameworks and the significance of space for effectively managing the model.