• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1577-1582
• /
• 2013

In this paper, we have analyzed the performance of MIMO (Multi-Input Multi-Output) underwater acoustic communication by using the acquired data via the experiments in water tank. First of all, in the pursuit of this aim, we have measured the channel transfer characteristics at several transceiver locations. The transmitted signal was modulated by QPSK(Quadrature Phase Shit Keying) and the received signal was recovered through the detector that contains the zero forcing equalizer. A maximum 30~40 ms delay was appeared because of physically closed water tank environment that has the harsh multi-path transmission conditions. In result of experiment, even though the bit error rate showed comparatively large when $2{\times}2$ MIMO system with two transmitters and receivers was considered. However, we confirmed it has approximately 15% enhanced performance compared with SISO (Single-Input Single-Output) system.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.6
• /
• pp.324-332
• /
• 2005

In general, bus system consumes a very significant portion of power in a chip. Bus splitting can be used to reduce the energy dissipation and to reduce the Propagation delay on the bus by lowering the parasitic load of each bus segment. Data exchange probability distribution between a set of interconnected processing elements affects the average energy dissipation of the splitted bus architectures. In this research, we have developed tree-based bus splitting techniques and design methodologies, as an extension of horizontally aligned bus splitting. We have developed the methodology to select near-optimal bus architectures for low energy dissipation when data exchange probability distribution of a system is given. Experimental results show that the proposed techniques can reduce energy dissipation on the bus by up to 83$\%$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39B no.6
• /
• pp.360-369
• /
• 2014

Underwater Acoustic Sensor Networks(UASN) enables varied study from collected data of underwater environments such as pollution monitoring, disaster prevention. The collected data is transmitted from underwater to terrestrial communication entity by acoustic communication. Because of the constraints of underwater environments include low data rate and propagation delay, it is difficult to apply cryptographic techniques of terrestrial wireless communication to UASN. For this reason, if the cryptographic techniques are excluded, then collected data will be exposed to security threats, such as extortion and forgery, during transmission of data. So, the cryptographic techniques, such as the authentication and key establishment protocol which can confirm reliability of communication entities and help them share secret key for encryption of data, must need for protecting transmitted data against security threats. Thus, in this paper, we propose the light weight authentication and key establishment protocol.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.10a
• /
• pp.56-56
• /
• 1999

For advanced TFT-LCD manufacturing processes, dry etching of thin-film layers(a-Si, $SiN_x$, SID & gate electrodes, ITO etc.) is increasingly preferred instead of conventional wet etching processes. To dry etch Al gate electrode which is advantageous for reducing propagation delay time of scan signals, high etch rate, slope angle control, and etch uniformity are required. For the Al gate electrode, some metals such as Ti and Nd are added in Al to prevent hillocks during post-annealing processes in addition to gaining low-resistivity($<10u{\Omega}{\cdot}cm$), high performance to heat tolerance and corrosion tolerance of Al thin films. In the case of AI-Nd alloy films, however, low etch rate and poor selectivity over photoresist are remained as a problem. In this study, to enhance the etch rates together with etch uniformity of AI-Nd alloys, magnetized inductively coupled plasma(MICP) have been used instead of conventional ICP and the effects of various magnets and processes conditions have been studied. MICP was consisted of fourteen pairs of permanent magnets arranged along the inside of chamber wall and also a Helmholtz type axial electromagnets was located outside the chamber. Gas combinations of $Cl_2,{\;}BCl_3$, and HBr were used with pressures between 5mTorr and 30mTorr, rf-bias voltages from -50Vto -200V, and inductive powers from 400W to 800W. In the case of $Cl_2/BCl_3$ plasma chemistry, the etch rate of AI-Nd films and etch selectivity over photoresist increased with $BCl_3$ rich etch chemistries for both with and without the magnets. The highest etch rate of $1,000{\AA}/min$, however, could be obtained with the magnets(both the multi-dipole magnets and the electromagnets). Under an optimized electromagnetic strength, etch uniformity of less than 5% also could be obtained under the above conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1605-1614
• /
• 1992

The effects of % overload (% O.L), baseline stress intensity factor range (.DELTA. $K_{b}$) and dimension-less crack depth (a/W) are examined for the retardation behaviors after a single overload and high-low block loads in 7075-T73 aluminum alloy. And wheeler model, which is one of the fatigue life prediction models, is modified to predict retardation life using these test results. The retardation cycles( $N_{d}$) increased with a decrease in a/W and an increase in % O.L. and (.DELTA. $K_{b}$) These effects are more severe after high-low block loads than single overload. In the case of single overload, the main mechanisms of the retardation are the crack closure and the relaxation of K due to crack branching. But in the case of high-low block loads, that of the main mechanism is the crack closure caused by the accumulated compressive residual stree at the crack tip, which is related with the contact of fracture surfaces. Test results were multiple regression analyzed and got regressed shaping correction factors, (n)$_{REG}$, as function of %O.L., a/W and (.DELTA. $K_{b}$) Wheeler model is modified by using these (n)$_{REG}$. The number of delay cycles calculated by modified Wheeler model were in good agreement with the test results of this study.y.udy.y.y.y.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.4
• /
• pp.1344-1367
• /
• 2014

Mobile traffic is increasing a masse because of the propagation of the Internet and the development of wireless mobile technology. Accordingly, the Network Local Mobility Management (NETLMM) working group [1] of the Internet Engineering Task Force (IETF) has standardized Proxy Mobile IPv6 (PMIPv6) [2] as a protocol for accomplishing the transmissibility of mobile terminals. PMIPv6 is a network-led IP-based mobility management protocol, which can control terminal mobility without depending on the type of access system or the capability of the terminal. By combining PMIPv6 and the mobility of Session Initiation Protocol (SIP), we can establish terminal mobility and session mobility through a more effective route. The mobility function can be improved and the overlap of function reduced as compared to that in the case of independent operation. PMIPv6 is appropriate for a non-real-time service using TCP, and SIP is appropriate for a real-time service using RTP/UDP. Thus, in the case of a terminal using both services, an effective mobility management is possible only by using PMIPv6 together with SIP. In order to manage mobility in this manner, researches on PMIPv6-SIP are in progress. In line with this trend, this paper suggests a new PMIPv6-SIP architecture where when a mobile terminal conducts a handover, a network-led handover while maintaining the session without the addition of a special function or middleware is possible along with effective performance evaluation through mathematical modeling by comparing the delay and the packet loss that occur during the handover to the Pure-SIP.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.3
• /
• pp.1-10
• /
• 2012

A low-complexity Multiplication over GF(2m) and multiplier circuit has been proposed by using cyclic-shift coefficients and the irreducible trinomial. The proposed circuit has the parallel input/output architecture and shows the lower-complexity than others with the characteristics of the cyclic-shift coefficients and the irreducible trinomial modular computation. The proposed multiplier is composed of $2m^2$ 2-input AND gates and m (m+2) 2-input XOR gates without the memories and switches. And the minimum propagation delay is $T_A+(2+{\lceil}log_2m{\rceil})T_X$. The Proposed circuit architecture is well suited to VLSI implementation because it is simple, regular and modular.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.2
• /
• pp.124-130
• /
• 2013

The performance of underwater acoustic communication system is sensitive to the ISI(Inter-Symbol Interference) due to delay spread develop of multipath signal propagation. The equalizer is used to combat the ISI. In this paper, the performances of underwater acoustic communication with turbo equalizer were evaluated by real data collected in Korean littoral sea. As a result, when one iterative decoding using turbo equalizer is applied, the performance was improved 1.5 dB than the case of the non-iterative equalizer at BER $10^{-4}$. In the case of two or three iterations the performance was enhanced about 3.5 dB, but the performance wasn't improved any more in the case of more than three times.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.1
• /
• pp.91-100
• /
• 2010

According to the recent increase in air traffic a more efficient air traffic flow control is required. This paper proposes the algorithm for efficient air traffic flow control. Aeronautical communication environment is different from the common communication environment since it needs a direct communication between stations (or airplanes) and requires a strict priority for safety message. Moreover, the wide area for basic service causes high propagation delay. In this paper, by using existing CSMA/CA Media Access Control (MAC) protocol, we set the message priorities according to air traffic condition (congestion airport area, approach control area, En route area, and ocean area). This prioritization scheme enables the data transmission with higher access probability. Simulation results confirm that our protocol shows better performance in terms of channel efficiency and success probability compared to exisiting CSMA/CA protocol.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.5
• /
• pp.46-54
• /
• 1984

A silicon-gate n-well CMOS process with 3 $\mu$m gate length was developed and its possibility for the applications was discussed,. Threshold voltage was easily controlled by ion implantation and 3-$\mu$m gate length with 650 $\AA$ oxide shows ignorable short channel effect. Large value of Al-n+ contact resistance is one of the problems in fabrications of VLSI circuits. Transfer characteristics of CMOS inverter is fairly good and the propagation delay time per stage in ring oscillator with layout of (W/L) PMOS /(W/L) NMOS =(10/5)/(5/5) is about 3.4 nsec. catch-up occurs on substrate current of 3-5 mA in this process and critically dependent on the well doping density and nt-source to n-well space. Therefore, research, more on latch-up characteristics as a function of n-well profile and design rule, especially n+-source to n-well space, is required.