• Clean Technology
• /
• v.19 no.4
• /
• pp.370-378
• /
• 2013

This review has shown the capability of MOFs and ZIFs materials to adsorb $CO_2$ under typical PSA temperatures and pressures. The usual operating conditions are adsorption temperatures of $15{\sim}40^{\circ}C$ and adsorption pressures of 4~6 bar based on numerous PSA processes which are widely employed in gases industry for adsorptive separation of $CO_2$. The extent of $CO_2$ adsorption on the microporous materials depends on the metal species and organic linkers existing in the frameworks. The pore size and the surface area, and the process variables are the key parameters to be associated with the efficiency of the adsorbents, particularly adsorption pressures if other variables are comparable each other. The MOFs and ZIFs materials require high pressures greater than 15 bar to yield significant $CO_2$ uptakes. They possess a $CO_2$ adsorption capacity which is very similar to or less than that of conventional benchmark adsorbents such as zeolites and activated carbons. Consequently, those materials have been much less cost-effective for adsorptive $CO_2$ separation to date because of very high production price and the absence of commercially-proven PSA processes using such new adsorbents.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.3
• /
• pp.53-61
• /
• 2016

Solar assisted heat pump system uses solar thermal energy as a heat source of evaporator of heat pump. So, COP can be enhanced as well as collector efficiency. For improving performance of this system, some research about hybrid solar collector that has fin-and-tube heat exchanger has been conducted. This collector can get a thermal energy from ambient air for liquid heating, so heated liquid can be used as a heat source of evaporator in heat pump even the solar radiation is not enough. In this study, numerical analysis was conducted for confirming heat gain of liquid according to fin height and pitch of fin-and-tube heat exchanger in collector. As a result, higher heat gain was obtained on lower fin height and narrow fin pitch, but the pressure drop also increased with increment of heat gain. Thus the JF factor considering both heat transfer enhancement and pressure drop was investigated and the maximum value was shown when the fin height and pitch were 40mm and 45mm. So it is considered that this installation condition has a highest heat transfer improvement when comparing with pressure drop. However heat gain of liquid at this condition was less than the other installation conditions of fin pitch on same height. Then, after establishing a proper minimum heat gain of liquid, actual production and experiment of collector will be conducted with fin height and pitch showing maximum JF factor and satisfying selected minimum heat gain of liquid on the basis of results of this study.

• Korean Journal of Veterinary Research
• /
• v.40 no.2
• /
• pp.383-391
• /
• 2000

Milk urea nitrogen (MUN) determination is being used an indicator of the protein-energy balance in dairy herds. A faulty balance can be corrected to optimize milk production and animal health. This parameter is regarded as a potential tool to evaluate suboptimal feeding practices and reproductive disorders. Therefore, the purpose of this study was to investigate the response of milk composition by regular feeding analysis and to compared the relationship between MUN and milk protein(MP) and fertility at the insemination period in Holstein dairy cows. Total of 355 artificial insemination (AI) for 150 Holstein cows in the herd were used to examine the relationship between MUN and MP content and conception rate. The AI occured for the cows 50 to 150 day in milk, and MUN and MP concentration were determined using automated infrared procedures. The mean${\pm}$standard deviation of MUN and MP concentration in the herd were $15.6{\pm}2.1mg/dl$ and $3.23{\pm}0.38%$, respectively. MUN contents of bulk milk were increase by elevated crude protein intake. The conception rate was lower in the cows in which the level of MUN was lower than > 8.0mg/dl (10.0%) or > higher than 25mg/dl (15.4%) relative to the cows in MUN content of 12.0~17.9 mg/dl (36.7%) at the time of insemination. Also, lower MP than 3.0% or higher MP than 3.25% were associated with a lower conception rates. Consequently, MUN and MP analyses may be used serve as a monitoring tool of protein and energy nutritional balance to improve reproduction efficiency in Holstein dairy cows.

• Land and Housing Review
• /
• v.4 no.4
• /
• pp.425-434
• /
• 2013

The Small and Medium Business Administration specified 123 construction materials mandatory to purchase directly and forced the public owners to provide the contractors with materials as required by related law. This study extensively reviewed various characteristics and management factors of the owner-providing materials consumed in the public apartment housing under Direct Buying System(DBS) from the public owner's perspective. Subsequently, the major managed materials were identified, and the proper response plan was developed along the material procurement process. The Procurement Management Load Indices (PMLI) of 43 materials were evaluated according to rating criteria with procurement path, project-specified level, user requirement level, supplier's responsibility, on-site work requirement, additional parts, and inspection standards. The tile and aluminum windows were classified in the group needing high-level procurement efforts to reduce the errors and ensure the efficiency. The accurate quantity estimation method, definite purchase details, management activity definition before and after production, additional quantity for rework, interference coordination were defined as the essential activities for effectively responding to DBS.

• Membrane Journal
• /
• v.28 no.5
• /
• pp.307-319
• /
• 2018

Ion-exchange membrane (IEM) has fixed charge groups and is a separation membrane which is capable of selectively transporting ions of the opposite polarity. Recently, the interest in IEMs has been increasing as the importance of the desalination and energy conversion processes using them as the key components has increased. Since the IEMs determine the efficiency of the above process, it is necessary to improve the separation performance and durability of them and also to lower the expensive membrane price, which is a hindrance to the widening application of the IEM process. Therefore, it is urgent to develop high-performance and low-cost IEMs. Among various types of IEMs, pore-filled membranes prepared by filling ionomer into a porous polymer substrate are intermediate forms of homogeneous membranes and heterogeneous membranes. The production cost would be cheap like the case of heterogeneous membranes because of the use of inexpensive supports and the reduction of the amount used of raw materials, and at the same time, they exhibit excellent electrochemical characteristics close to homogeneous membranes. In this review, major research and development trends of pore-filled IEMs, which are attracting attention as high-performance and low-cost IEMs, have been summarized and reported according to the application fields.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.10
• /
• pp.583-589
• /
• 2015

This study was performed to evaluate the feasibility of anaerobic pretreatment for the leachate solubilized from thermal hydrolysis of sewage sludge cake. Overall process for the treatment of sludge cake consists of thermal hydrolysis, crystallization of magnesium, ammonium, and phosphate (MAP) for the leachate and anaerobic digestion of supernatant from MAP crystallization. The experimental evidence showed that the optimum ratio of Mg : P for the struvite crystallization of leachate solubilized from thermal hydrolysis of sludge cake was 1.5 to 1.0 as weight basis at the pH of 9.5. With this operational condition, the removal efficiencies of ammonia nitrogen and phosphorous achieved 50% and 97%, respectively. The mesophilic batch test showed that the ultimate biodegradability of the supernatant from MAP crystallization reached 63% at S/I ratio of 0.5. The readily biodegradable fraction of 90% ($S_1$) of the MAP supernatant BVS (Biodegradable Volatile Solids, $S_0$) degraded with $k_1$ of $0.207day^{-1}$ for the initial 17 days where as the rest slowly biodegradable fraction ($S_2$) of 10% of BVS degraded with $k_2$ of $0.02day^{-1}$ for the rest of the operational period. Semi-Continuously Fed and Mixed Reactor (SCFMR) was chosen as one of the best candidates to treat the MAP supernatant because of its total solids content over 6%. Maximum average biogas production rates reached 0.45 v/v-d and TVS removal efficiency of 37~41% was achieved at an hydraulic retention time (HRT) of 20 days and its corresponding organic loading rate (OLR) of 1.43 g VS/L-d.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.4
• /
• pp.315-320
• /
• 2002

The multifunctional compound such as conjugated linoleic acid (CLA) was used to producing of functional larval rockfish. Artemia, livefoods for larval fish, enriched with highly unsaturated fatty acids (HUFA) and CLA ($0.5\%$, $1.0\%$, $2.5\%$ and $5.5\%$ group) was fed to larval rockfish. Artemia, enriched with $2.5\~5.0\%$ of CLA, negatively affects the quality of larval rockfish. But $1.0\%$ CLA fed group shown to good specific growth rate, feed efficiency, n-3/n-6 PUFA ratio, DHA/EPA ratio and hematology results. The CLA deposited in muscle lipids of larval rockfish was reached 6.57 to $19.69\%$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.2
• /
• pp.47-53
• /
• 2014

Three kinds of crystalline silicon have been used for the solar cell grade. First of all, single crystalline silicon is the main subject to enhance the production yield. Most of the efforts are focused on the control of the melt-crystal interface shape affected by the crystal-crucible rotation rate. The main subject in the multi-crystalline silicon ingot is the contamination control. Faster Ar gas flow above the melt surface will lower the carbon contamination in the crystal. And also, twin boundary electrically inactive is found to be more effective than grain boundary for the improvement of the MCLT. In the case of mono-like silicon material, propagation of the multi-crystalline silicon growing from the inner side crucible is the problem lowering the portion of the single crystalline part at the center of the ingot. Crystal growing apparatus giving higher cooling rate at the bottom and lower cooling rate at the side crucible was suggested as the optimum solution obtaining higher quality of the mono-like silicon ingot. Proper application of the seeds at the bottom of the crucible would be one of the solutions.

• Proceedings of the Korea Environmental Mutagen Society Conference
• /
• 2002.05a
• /
• pp.36-42
• /
• 2002

Diesel exhaust (DE) has been recognized as a noxious mutagen and/or carcinogen, because its components can form DNA adducts. Mechanisms governing the susceptibility to DE and the efficiency of such DNA adduct formation require clarification. The transcription factor Nrf2 is essential for inducible and/or constitutive expression of a group of detoxification and antioxidant enzymes, and we hypothesized that the nrf2 gene knockout mouse might serve as an excellent model system for analyzing DE toxicity. To address this hypothesis, lungs from nrf2(-/-) and nrf2(+/-) mice were examined for the production of xenobiotic-DNA adducts after exposure to DE (3 $mg/m^{3}$ suspended particulate matter) for 4 weeks. Whereas the relative adduct levels (RAL) were significantly increased in the lungs of both nrf2(+/-) and nrf2(-/-) mice upon exposure to DE, the increase of RAL in the lungs from nrf2(-/-) mice exposed to DE were approximately 2.3-fold higher than that of nrf2(+/-) mite exposed to DE. In contrail, cytochrome P4501Al mRNA levels in the nrf2(-/-)mouse lungs were similar to those in the nrf2(+/-) mouse lungs even after exposure to DE, suggesting that suppressed activity of phase II drug-metabolizing enzymes is important in giving ise to the increased level of DNA adducts in the Nrf2-null mutant mouse subjected to DE. Importantly, severe hyperplasia and accumulation of the oxidative DNA adduct 8-hydroxydeoxyguanosine were observed in the bronchial epidermis of nrf(-/-) mite following DE exposure. These results demonstrate the increased susceptibility of the nrf2 germ line mutant mouse to DE exposure and indicate the nrf2 gene knockout mouse nay represent a valuable model for the assessment of respiratory DE toxicity.

• Journal of Environmental Science International
• /
• v.6 no.3
• /
• pp.267-276
• /
• 1997

It has been studded that combustion and the production of air pollution of anthracite - bituminous coal blend In a fluidized bed coal combustor, The objects of thIns study were to investigate mixing characteristics of the particles as well as the combustibility of the low grade domestic anthracite coal and Imported h19h calorific bltununous coal in the fluidized bed coal combustor. They were used as coal samples ; the domestic low grade anthracite coal with heating value of 2,010kca1/kg and the Imported high grade bituminous coal with beating value of 6,520kca1/kg. Also, the effects of air flow rate and anthracite fraction on the reaching time of steady state condition have been studied. The experimental results are presented as follows. The time of reaching to steady state was affected by the temperature variation. The steady state time was about 120 minute at 300sc1h which was the fastest. It has been found that $O^2$ and $CO^2$ concentration were reached steady state at about 100 minute. It has been found that $O^2$ concentration decreased and $CO^2$ concentration increased as the height of fluidlzed bed Increased. It was found that splash zone was mainly located from 25cm to 35cm above distributor. Also, as anthracite traction Increased, the mass of elutrlatlon particles Increased, and $CO^2$ concentration decreased. As gk flow rate Increased,$O^2$ concentration decreased and $CO^2$ concentration increased. Regardless of anthracite fraction and flow rate, the uncombustible weight percentage according to average diameter of elutriation particles were approldmately high In the case of One Particles. As anthracite traction and k now rate Increased, elutriation ratio Increased. As anthracite fraction was increased, exit combustible content over feeding combustible content was Increased. Regardless of anthracite fraction, size distribution of Ued material from discharge was almost constant. Over bed temperature 85$0^{\circ}C$ and excess air 20% , the difference of combution efficiencies were little. It is estimate that the combustion condition In anthracite-bituminous coal blend combustion is suitable at the velocity 0.3m/s, bed temperature 85$0^{\circ}C$, the excess air 20%.