• 한국정보전자통신기술학회논문지
• /
• 제11권6호
• /
• pp.742-750
• /
• 2018

본 논문에서는 $0.13{\mu}m$ BCD 공정 기반에서 5V MOS 소자만 사용하여 zero layer FTP 셀이 가능하도록 하기 위해 tunnel oxide 두께를 기존의 $82{\AA}$에서 5V MOS 소자의 gate oxide 두께인 $125{\AA}$을 그대로 사용하였고, 기존의 DNW은 BCD 공정에서 default로 사용하는 HDNW layer를 사용하였다. 그래서 제안된 zero layer FTP 셀은 tunnel oxide와 DNW 마스크의 추가가 필요 없도록 하였다. 그리고 메모리 IP 설계 관점에서는 designer memory 영역과 user memory 영역으로 나누는 dual memory 구조 대신 PMIC 칩의 아날로그 회로의 트리밍에만 사용하는 single memory 구조를 사용하였다. 또한 BGR(Bandgap Reference Voltage) 발생회로의 start-up 회로는 1.8V~5.5V의 전압 영역에서 동작하도록 설계하였다. 한편 64비트 FTP 메모리 IP가 power-on 되면 internal reset 신호에 의해 initial read data를 00H를 유지하도록 설계하였다. $0.13{\mu}m$ Magnachip 반도체 BCD 공정을 이용하여 설계된 64비트 FTP IP의 레이아웃 사이즈는 $485.21{\mu}m{\times}440.665{\mu}m$($=0.214mm^2$)이다.

• Journal of Power Electronics
• /
• 제7권4호
• /
• pp.343-352
• /
• 2007

This paper proposes a modularized charge equalization converter for hybrid electric vehicle (HEV) lithium-ion battery cells, in which the intra-module and the inter-module equalizer are Implemented. Considering the high voltage HEV battery pack, over approximately 300V, the proposed equalization circuit modularizes the entire $M^*N$ cells; in other words, M modules in the string and N cells in each module. With this modularization, low voltage stress on all the electronic devices, below roughly 64V, can be obtained. In the intra-module equalization, a current-fed DC/DC converter with cell selection switches is employed. By conducting these selection switches, concentrated charging of the specific under charged cells can be performed. On the other hand, the inter-module equalizer makes use of a voltage-fed DC/DC converter for bi-directional equalization. In the proposed circuit, these two converters can share the MOSFET switch so that low cost and small size can be achieved. In addition, the absence of any additional reset circuitry in the inter-module equalizer allows for further size reduction, concurrently conducting the multiple cell selection switches allows for shorter equalization time, and employing the optimal power rating design rule allows fur high power density to be obtained. Experimental results of an implemented prototype show that the proposed equalization scheme has the promised cell balancing performance for the 7Ah HEV lithium-ion battery string while maintaining low voltage stress, low cost, small size, and short equalization time.

• 한국가스학회지
• /
• 제27권1호
• /
• pp.57-62
• /
• 2023

정압기 EVENT는 각 지역정압기(이하 "정압기")에 설치된 원격감시장치가 보내는 신호로 당사 Client서버에서 직관적으로 확인할 수 있는 이상경보이다. 이는 정압기 이상발생 시 상황실에서 즉각적으로 출동명령 및 초동조치를 가능토록 하며 정압기 이상원인을 분석할 수 있는 중요한 Data이다. 최근 3년간 정압기 EVENT Data의 추이를 살펴보면 비점검 EVENT Data 증가 추세가 뚜렷하다. 비점검 EVENT(실제이상 또는 Noise EVENT)가 증가한다는 것은 첫째로 실제 정압기에 기계적 이상이나 압력이상 발생이 증가한다는 의미일 수도 있으며, 둘째로 실제 정압기엔 이상이 없지만 원격감시장치에서 발생한 통신오류, Reset오류, 센서오류, 전원오류(순간정전) 등에 의하여 정압기에 이상이 생긴 것처럼 EVENT Data가 형성될 수도 있다. 이중 본 연구에서는 최근 발생한 비점검 EVENT Data를 분석하여 Noise EVENT인 원격감시장치 오류 중 Critical Noise Event를 확인하고 이를 감소시켜 정압기 EVENT의 신뢰성을 높일 수 있는 방안에 대해 검토하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권7호
• /
• pp.418-423
• /
• 2000

The fiber Fabry-Perot interferometric(FFPI) sensor is well known in the field of industrial diagnosis due to its outstanding properties such as tiny size, simple and rugged structure, and easy interrogation. As other fiber interferometric sensors, it also suffers from ambiguous output caused by highly periodic feature in its optical transfer function. In most cases, the ambiguity leads to relatively short dynamic operating range and long processing time during power-on reset, which limits its application to some specific fields requiring very high resolution. In this paper a method based on double sensing scheme was proposed to overcome the above difficulty. By employing a fringe selection auxiliary FFPI sensor the original FFPI sensor can identify its true position on the phase domain. The performance test with 10mm FFPI sensor and a thermocouple temperature sensor for reference shows wide dynamic range 0-900$\ell$ keeping a reasonable resolution of 0.1$\ell$ over the entire range.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권9호
• /
• pp.467-475
• /
• 1999

This paper presents an analysis method of a forward converter, using both the finite element method considering the external circuit and a state variables equation. The converter operates at 50kHz and its one period is divided into two modes for the simplicity of the analysis. In the first mode, the switching transistor turns on and an input power is transferred into the load by the electromagnetic conversion action of a ferrite transformer. In the second mode, the switching transistor turns off and the stored energy in an inductor is delivered to the load, and the transformer core is demagnetized by the reset winding current. In this paper, time-stepping finite element method taking into account the on-state electrical circuit of the converter in used to analyze both the electrical circuit and electromagnetic field of the magnetic device during the first mode and the demagnetization period of the transformer core. Then a state variables equation for the circuit which the inductor current flows is constituted and solved during the second mode. As a result, the simulation results have been good agreement with the results obtained form experiment.

• Transactions on Electrical and Electronic Materials
• /
• 제11권1호
• /
• pp.20-23
• /
• 2010

The analog front end (AFE) of a radio frequency identification transponder using the ISO 14443 type A standard with a 100% amplitude shift keying (ASK) modulation is proposed in this paper and verified by circuit simulations and measurements. This AFE circuit, using a 13.56 MHz carrier frequency, consists of a rectifier, a modulator, a demodulator, a regulator, a power on reset, and a dynamically enabled digital phase locked loop (DPLL). The DPLL, with a charge pump enable circuit, was used to recover the clock of a 100% modulated ASK signal during the pause period. A high voltage lateral double diffused metal-oxide semiconductor transistor was used to protect the rectifier and the clock recovery circuit from high voltages. The proposed AFE was fabricated using the $0.18\;{\mu}m$ standard CMOS process, with an AFE core size of $350\;{\mu}m\;{\times}\;230\;{\mu}m$. The measurement results show that the DPLL, using a demodulator output signal, generates a constant 1.695 MHz clock during the pause period of the 100% ASK signal.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.252-257
• /
• 2017

In this paper for developing and implementing the HD level triple streaming hybrid security camera which output the three type of video outputs(HD-SDI, EX-SDI, Analog). We design the hardware and program the firmware supporting the main and sub functions. We use MN34229PL as image sensor, EN778, EN331 as image processor, KA909A as reset, iris, day&night function part, A3901SEJTR-T as zoom/focus control part. We request the performance test of developed security camera at the broadcasting and communication fusion testing department of TTA (Telecommunication Technology Association). We can get the three outputs (HD-SDI, EX-SDI, Analog) from the developed security camera, get the world best level at the jitter and eye pattern amplitude value and exceed the world best level at the signal/noise ratio, and minium illumination, power consumption part. The HD level triple streaming hybrid security camera in this paper will be widely used at the security camera because of the better performance and function.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1317-1318
• /
• 2015

최근 ICT 기술의 발전으로 원거리에 위치한 광역 상수도의 취수장, 가압장, 감압변실 및 배수지 등의 시설물은 중앙제어실에서 효율적인 설비운영을 위해 원격통합관리로 감시제어를 수행하여 생산성을 제고하고 있다. 단위사업장에 낙뢰 유입으로 인한 순간정전이나 오동작 등의 영향에 의한 누전차단기 트립 증상이나 제어계측설비의 시스템 다운현상이 발생할 경우에 전원설비나 계측제어설비를 복구하기 위해서는 운영자가 사업장 현장에 출동하여 설비를 복구해야만 한다. 출동에 따른 많은 시간과 비용이 발생할 뿐만 아니라 응급조치가 미흡할 경우에는 수돗물 공급 중단 등의 위험성이 발생할 소지가 있다. 본 논문에서는 단위사업장의 서지유입이나 설비 오동작 등의 원인으로 무인사업장 설비에 System down 현상이 발생하면 단위사업장에 출동하지 않고 원격의 중앙제어실에서 원격 명령 또는 자동 프로그램에 의한 전원 Reset 동작으로 현장 제어설비가 원활하게 동작함으로써 무인사업장의 효율적인 운영관리가 가능한 원격제어 전원관리시스템 구축사례를 제시하고자 한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.282-282
• /
• 2011

Low power consuming operation of phase-change random access memory (PRAM) can be achieved by confining the switching volume of phase change media into nanometer scale. Ge2Sb2Te5 (GST) is one of the best materials for the phase change random access memory (PRAM) because the GST has two stable states, namely, high and low resistance values, which correspond to the amorphous and crystalline phases of GST, respectively. However, achieving the fast operation speed at lower current requires an alternative chalcogenide material to replace the GST and shrinking the dimension of programmable volume. In this paper, we have fabricated nanoscale contact area on Ge2Sb2Te5 thin films with trimming process. The GST material was fabricated by melt quenching method and the GST thin films were deposited with thickness of 100 nm by the electron beam evaporation system. As a result, the reset current can be safely scaled down by reducing the device contact area and we could confirmed the phase-change characteristics by applying voltage pulses.

• 드라이브 ㆍ 컨트롤
• /
• 제15권4호
• /
• pp.30-38
• /
• 2018

Electronic control units (ECUs) are currently popular, and have evolved further towards the high-end application of autonomous vehicles in the automotive industry. Such digital technologies have also become widespread, in agriculture and construction equipment. Likewise, transmission control of high-speed tracked vehicles is based on the transmission control unit (TCU), performing complex gear change control functions, and diagnostic algorithms (a TCU's self-diagnostic and reporting capability of malfunction data through CAN communication). Since all functions of TCU are implemented by embedded-software, it is hardly possible to analyze specifications by reverse engineering. In this paper a real-time transmission simulator adaptable to TCU is presented, for analysis of diagnosis algorithm and standards. Signal simulation circuits are deliberately designed considering electrical characteristics of TCU inputs and various analysis tools, such as analog input auto scan function, and global output enable switch, are implemented in software. Test results from hardware-in-the-loop simulator verify tolerance time for each error, as well as cause of fault, error reset conditions.