• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.6
• /
• pp.1-8
• /
• 2011

Power Line Communication (PLC: Power Line Communication) to propagate the current power lines are in every household of the existing infrastructure is the most extensive network configuration. In addition, the cost required for network configuration, the advantage of almost zero for the investors and is sufficient to attract the attention of operators. The PLC is supply power to power lines used the voice and data communication technologies put it on KHz ~ tens of hundreds of high-frequency signal MHz. But because uses power lines as existing wireless communications systems will occurs interference. The notch filters of a common way to eliminate the interference are used. In this paper, a dynamic high-performance notch filter applying CIC filter performance was verified through MATLAB and was implemented using a TI's TMS320C6416T DSP board.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.264-273
• /
• 2005

Broadband power line communications have been receiving tremendous interest In recent years because this technology enables utilities to deploy a communication network over existing power line infrastructures. Despite the enormous potential, there is some skepticism about the technology and its commercial viability. In this paper, we investigate the performance characteristic of PLC through field test carried out in actual households. Also it addresses major field deployment aspects, such as range, coverage, the number of node for operation and maintenance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.2B
• /
• pp.145-150
• /
• 2002

This paper presents an implementation methodology of unified PCS base station system which, is capable of providing PCS services for 3 PCS carriers concurrently. We have built up an unified PCS BTS using a unification module, which is consisted of a multi-channel combiner, duplexer, LNA, power divider, feeder line, and a common set of antennas. PCS unification module is featured with wide-band and high power handling capability and electrical characteristics like insertion loss, isolation have been greatly improved. It was shown that performance of the system in terms of Ec/Io and mobile receive power within the total 30MHz PCS frequency range is uniformly acceptable and measured signal quality and coverage are equivalent to that of the individual PCS base station.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.95-100
• /
• 2021

If we know the location of the hull block and the welding feeder in the shipyard, we can easily obtain the location information of the worker. That data is very useful for implementing a workplace safety monitoring system. However, it is difficult to apply a fixed communication network to the workplace due to the specificity of the hull structure and welding process. In this study, inductive power line communication, which can replace dedicated communication line, was reviewed. A ferrite core was used as an inductive coupler to be installed on the power cable of the welding machine, and a nano-crystalline core was applied as a coupler to be fastened to the support rod of the metal block. In order to visualize the operating principle of the proposed couplers, 3D modeling and finite element analysis were performed with the COMSOL AC/DC module. In the communication performance test using an aluminum profile, when the communication channel was formed by the contact of the welding electrode, the bandwidth was kept above 6 Mbps.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.587-592
• /
• 2020

The giant information exchange enabled by the Internet of Things paradigm will likely exploit electrical lines as a ready-to-use infrastructure. The advantage of using the pre-installed infrastructure of wiring networks makes power line communication a competitive technology for broad-band communications. Therefore, there has been a growing interest towards the use of existing power line communication channels as an effective means for transmitting high speed data and Internet service. One of the main noise types affecting power line communication systems is the impulsive noise, and the focus of this work is on the impact of this impulsive noise on the performance of OFDM-QPSK systems. For the performance analysis of impulsive noise, data measured in three environments were used. Through the analysis, it is shown that OFDM-QPSK system outperforms QPSK system for most of the impulsive noise cases. Also, RS-coded OFDM-QPSK system can achieve good BER performance under 3 cases impulsive noise environment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8C
• /
• pp.637-644
• /
• 2012

In this paper, a new compact power divider is suggested. Instead of the quarter wavelength transmission line(TX-line)s for the branches of the conventional Wilkinson's power divider design method, we use our composite right- and left-handed(CRLH) TX-line zeroth order resonator(ZOR) bandpass filters of one twelfth wavelength and reduce the physical length of the power divider. Besides, the filters in the branches can secure the passband for power-division. To validate the proposed power divider, we take an L-band for millitary satellaite transponder as the test case and the performances of the circuit and full-wave simulation results with the CRLH properties of the structure are shown with the dispersion curve and E-field at the ZOR. The measurement is compared with the simulation results. Also, the size reduction effect by the proposed scheme is addressed

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.4
• /
• pp.691-700
• /
• 1994

A power line in not so good in characteristics for communication, because it is a media to transfer the commercial electrical power, and its load noise and high frequency noise are so much. Thus, a simple method to transfer a remote control signal on the power line is studied. The already-existing method is that two signals with upper part eliminated is transmitted every N step. But the method is investigated which the transmitter sends a period signal eliminated in arbitrary phase. Thus the transmission power loss due to elimination of signal can be reduced to the minimum. To implement it, a timer calculating the time from zero-crossing point to the phase is required. The micro-controller, 87C51, precisely calculates the phase using one of two built-in timers. As a result, a remote control signal tramsmitter and receiver using a partially eliminated signal, which is better than the conventional technique using half-eliminated signal in a efficiency of power transmission, is realized, and its characteristics are analyzed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.799-804
• /
• 2016

Broadband powerline communication (BPLC) uses distribution lines as a medium for achieving effective bidirectional data communication along with electric current flow. As the material characteristics of power lines are not good at the communication channel, the development of power line communication (PLC) systems for internet, voice, and data services requires measurement-based models of the transfer characteristics of the network suitable for performance analysis by simulation. In this paper, an analytic model describing a complex transfer function is presented to obtain the attenuation and path parameters for a multipath power line model. The calculated results demonstrated frequency-selective fading in multipath channels and signal attenuation with frequency, and were in good agreement with the experimental results. Inductive coupling units are used as couplers for coupling the signal to the power line to avoid physical connections to the distribution line. The inductance of the ferrite core, which depends on the frequency, determines the cut-off frequency of the inductive coupler. Coupling loss can be minimized by increasing the number of windings around the coupler. Coupling efficiency was improved by more than 6 dB with three windings compared to the results obtained with one winding.

• Journal of Convergence Society for SMB
• /
• v.2 no.1
• /
• pp.19-24
• /
• 2012

In this paper, we propose the battery life time extension method in the multi-interface terminal by using the state information in an optical wireless integrated network architecture. When the bottlenecks occurs in the network, the terminal receives data packets via multipath. However, the battery life time is rapidly reduced because the power consumption of the terminal is bigger than single interface. For reducing the power consumption in the multi-interface terminal, the Optical Line Terminal (OLT) confirms whether the bottleneck phenomenon is occurred or not. And the network state information is transmitted to the terminal. The terminal turns one of the interfaces off to reduce the power consumption. In order to estimate the performance, we compare the power consumption between single and dual interfaces.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.3043-3045
• /
• 2005

기업체나 연구소와 같은 전자기자재의 사용이 많은 곳에서 효율적인 기자재 관리는 필수적이다. 이에 따라 모든 기자재를 관리하는 데이터베이스의 필요성이 대두된다. 본 논문은 데이터베이스를 카운터가 내장된 기자재로부터 추가적인 망의 포설 없이 기존의 전력선을 이용하여 음성통신과 초고속 통신이 가능한 전력선 통신(PLC:Power Line Communications)[1]를 통해 데이터베이스를 수집하고 수집된 데이터베이스를 무선으로 모니터링 할 수 있는 시스템을 구현하는데 그 목적이 있다. 이 시스템의 구현을 위해 ARM9 core를 기반으로 한 임베디드 리눅스 시스템에 웹서버, 무선프로토콜 등을 포팅하여 무선네트워크가 가능한 PDA, 노트북 등을 이용하여 손쉽게 모니터링 할 수 있는 시스템을 구현하고자 했다.