• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.93-97
• /
• 2000

In an era of very rapid technological change, standardization organizations have been confronted with the problem that they should develop more new and more complex standards as strategic tools for enforcement of competitive power in shorter time according to the reduction of Life Cycle of products and the increase in the number of standards and their complexity. To cope with this challenge, we introduce the functionalities and development directions for implementing standardization information system. Also this paper describes the architecture of the next generation system for standard information that enabling information sharing and exchanging using XML. Finally, we suggest implementation framework of Standardization Vortal Site for the One-stop service of integrated standards information which provide users with standards development roadmap and give brief introduction to SOL(Standards On-Line) site which is operated by ETRI/PEC.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.188.1-188.1
• /
• 2014

Aluminum is widely used as a material for electrode on silicon based devices. Especially, aluminum films are used as backside and front-side electrodes in silicon quantum dot (QD) solar cells. In this point, the diffusion of aluminum is very important for the enhancement of power conversion efficiency by improvement of contact property. Aluminum was deposited on a Si (100) wafer and a Si QD layer by ion beam sputter system with a DC ion gun. The Si QD layer was fabricated by $1100^{\circ}C$ annealing of the $SiO_2/SiO_1$ multilayer film grown by ion beam sputtering deposition. Cs ion beam with a low energy and a grazing incidence angle was used in SIMS depth profiling analysis to obtain high depth resolution. Diffusion behavior of aluminum in the Al/Si and Al/Si QD interfaces was investigated by secondary ion mass spectrometry (SIMS) as a function of heat treatment temperature. It was found that aluminum is diffused into Si substrate at $450^{\circ}C$. In this presentation, the effect of heat treatment temperature and Si nitride diffusion barrier on the diffusion of Al will be discussed.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.2
• /
• pp.202-211
• /
• 2014

The bulk current injection (BCI) and direct power injection (DPI) method have been established as the standards for the electromagnetic susceptibility (EMS) test. Because the BCI test uses a probe to inject magnetically coupled electromagnetic (EM) noise, there is a significant difference between the power supplied by the radio frequency (RF) generator and that transferred to the integrated circuit (IC). Thus, the immunity estimated by the forward power cannot show the susceptibility of the IC itself. This paper derives the real injected power at the failure point of the IC using the power transfer efficiency of the BCI method. We propose and mathematically derive the power transfer efficiency based on equivalent circuit models representing the BCI test setup. The BCI test is performed on I/O buffers with and without decoupling capacitors, and their immunities are evaluated based on the traditional forward power and the real injected power proposed in this work. The real injected power shows the actual noise power level that the IC can tolerate. Using the real injected power as an indicator for the EMS test, we show that the on-chip decoupling capacitor enhances the EM noise immunity.

• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.85-90
• /
• 2010

In this paper the effects of a Static Synchronous Series Compensator, which is constructed with a 48-pulse inverter, on the power demand from the grid are studied. Extensive simulation studies were carried out in the MATLAB simulation environment to observe the compensation achieved by the SSSC and its effects on the line voltage, line current, phase angle and real/reactive power. The designed device is simulated in a power system which is comprised of a three phase power source, a transmission line, line inductance and load. The system parameters such as line voltage, line current, reactive power Q and real power P transmissions are observed both when the SSSC is connected to and disconnected from the power system. The motivation for modeling a SSSC from a multi-pulse inverter is to enhance the voltage waveform of the device and this is observed in the total harmonic distortion (THD) analysis performed at the end of the paper. According to the results, the power flow and phase angle can be controlled successfully by the new device through voltage injection. Finally a THD analysis is performed to see the harmonics content. The effect on the quality of the line voltage and current is acceptable according to international standards.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.7
• /
• pp.52-58
• /
• 2012

In this study, we have investigated the effect of the solar power generation facilities on the power quality of interconnected solar power generation system. When the solar power generation facility was connected to the distribution system, whether the solar power generation is under operation or not, Peak factor of current was increased to 0.033[%], Frequency is deviated from $60{\pm}0.2$[Hz] and also Short term flicker indication($P_{st}$) increased to 0.213[p.u.] compare with the disconnected situation. Harmonic current [%] in orders was 11.42[%] maximum under 11th orders and was 7.861[%] between 11th and 17th orders. These values were about 3 or 4 times compared with "the power system interconnection technique standards" at the same situation above. Therefore, we could confirmed that the solar power generation facility, when it was connected to the existing distribution system, made bad influence on the power qualities such as the peak factor of current, frequency regulation, short term flicker indication($P_{st}$) and harmonic current [%] in orders etc.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.4
• /
• pp.18-21
• /
• 2017

We report a method for improving heat exchange between cryo-cooled large-power-dissipation devices and liquid cryogen. Micro-machined monolithic heat sinks were fabricated on a high integration density superconducting Josephson device, and studied for their effect on cooling the device. The monolithic heat sink showed a significant enhancement of cooling capability, which markedly improved the device operation under large dc- and microwave power dissipation. The detailed mechanism of the enhancement still needs further modeling and experiments in order to optimize the design of the heat sink.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.110-112
• /
• 2005

Recently, the reactor trip in nuclear power plants has mostly occurred by the failure of secondary electrical facilities. Some kinds of technical standards or acceptable criteria are required to regulate those facilities. Therefore, in this paper the failures of secondary electrical facilities which cause reactor trip are analyzed, and the inspection technologies including guidelines for secondary electrical facilities are developed.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2024-2026
• /
• 2001

This paper propose the new concept and design method of PC based automation in factory automation. In order to apply this system, the essentially proposed three technologies are following - Using the industrial automation control language, recognized by IEC 1131-3 - to apply Windows-NT operation system - to apply the Fieldbus network based on international standards.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.2
• /
• pp.106-113
• /
• 2012

Recently laws have been enacted to build and promote the use of smart grid. There are also increasing demands for the compliance with international trade agreements and the related international standards. Due to these rapid changes in electric power industry and the market expansion, importances of new technologies and processes have been being increased. To reflect these international trends, the government have carried out the designation of new technology for electric power industry to promote domestic industries and national competitiveness by inspiring technology developments in individual or private industry sectors. In this paper analysis of the current status of the designation of the new technology of electric power has been presented including its problem and effect on the related industries. The analysis is expected to be utilized to enhance sound development and to vitalize the electrical new technology regulation.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.249-256
• /
• 2009

As a wireless handset deals with multiple application standards concurrently, RF transmitters and power amplifiers are required to be more power efficient and reconfigurable. In this paper, we review the recent advances in the design of the power amplifiers and transmitters. Then, the systematic design approaches to improve the performance with the digital baseband signal processing are introduced for the next generation mobile handset.