• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.86-93
• /
• 2008

A low-power, low-noise, highly-linear hybrid balun circuit is proposed for 2.4-GHz fully differential CMOS direct conversion receivers. The hybrid balun is composed of a passive transformer and loss-compensating auxiliary amplifiers. Design issues regarding the optimal signal splitting and coupling between the transformer and compensating amplifiers are discussed. Implemented in $0.18{\mu}m$ CMOS process, the 2.4 GHz hybrid balun achieves 2.8 dB higher gain and 1.9 dB lower noise figure than its passive counterpart and +23 dBm of IIP3 only at a current consumption of 0.67 mA from 1.2 V supply. It is also examined that the hybrid balun can remarkably lower the total noise figure of a 2.4 GHz fully differential RF receiver only at a cost of 0.82 mW additional power dissipation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.4
• /
• pp.59-65
• /
• 2014

In this paper, in order to improve efficiency performance of power amplifiers, a mode changeable autotransformer is proposed. Efficiency performance at the low-power mode can be improved by adopting the mode changeable autotransformer. A dual-mode autotransfomrer CMOS power amplifier using a standard 0.18-${\mu}m$ CMOS process is designed in this work. Number of turns in a primary winding is re-configurated according to mode change between the high-power mode and the low-power mode. Thus, the efficiency performance of the power amplifier at each mode is optimized. EM and total circuit simulation results verify that low-power mode power added efficiency(PAE) at 24dBm output power is improved from 10.4% to 26.1% using the proposed multi-mode operation.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.626-632
• /
• 2017

This paper describes a high power amplifier combining eight low power amplifiers using a radial power combiner with low insertion loss. The radial power combiner is a non-resonant type combiner with 8 input ports and is implemented by microstrip transmission line. The combiner characteristics designed at operating frequency of 1.045 GHz have an insertion loss of 0.7 dB and a return loss of more than 12 dB. Also, the low power amplifier used was designed with AFT27S010NT1 transistor and designed to satisfy the same gain, phase and constant output characteristic at operating frequency. The high power amplifier, which combiners the radial power combiner and the drive amplifier of 8 W output by driving low power amplifiers obtained the output characteristic of 33 W at operating frequency of 1.045 GHz. Also, the change of the output characteristic of the amplifier using the radial combiner was graceful degradation when the low power amplifier failed one by one.

• Journal of Advanced Navigation Technology
• /
• v.22 no.4
• /
• pp.319-324
• /
• 2018

In this paper, a high power amplifier using RF power solid-state semiconductor is implemented to overcome a problem of plasma generator which has the low efficiency, short life span, the difficult maintenance and the high-operation cost. This power amplifier consists of a radial combiner of low-loss and high power operation and the sixteen 300 W power amplifiers to obtain 3 kW output power for high power operation implemented in semiconductors at industrial scientific medical (ISM) band of 2.45 GHz. In addition, this amplifier overcomes the problem of heat generation due to high power by applying a water-cooled structure to the individual amplifiers. This power amplifier, which is made up of a small system, achieves 50% efficiency at the desired output.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.327-330
• /
• 1998

A 2watts MMIC(Monolithic Microwave Integrated Circuits) SSPA(Solid State Power Amplifiers) for 20GHz band communication systems has been designed, manufactured and measured. The 0.15um pHEMT technologywith the gate size of 400um for single device was used for the fabrication of MMIC Power Amplifier chips. The precision MIC patterns for the peripherals like power combiner/divider and microstrip lines were realized using hard substrate for gold wire/ribbon bonding. The measured data shows that this MMIC SSPA has the linear gain of 18dB, output power of 33.42dBm(2.2Watts)at 20~21GHz.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.545-546
• /
• 2008

This paper presents a low power CMOS low noise amplifier for UWB applications. To reduce the power consumption, two cascode amplifiers was stacked in DC. Designed with $0.18-{\mu}m$ CMOS technology, the proposed LNA achieves 20dB flat gain, below 3dB noise figure, and the power consumption of 5.2mW from a 1.8 V supply voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.8
• /
• pp.802-807
• /
• 2014

In this paper, an accurate method to estimate the measurement uncertainty of a power amplifier was proposed. Because power amplifiers incorporate mismatch at the drain for the optimal performance, the general method is not enough to produce precise measurement uncertainty of the output power. In order to supplement this method, We suggest comprehensive power measurement uncertainty which is utilized by a complex reflection coefficient and measurement uncertainty of S-parameter which contain the mismatch at the drain on the power amplifier. After that, we compared it with real measurement results of the 10 watt power amplifier which operates on 3.7 GHz. As a result, suggested measurement uncertainty could obtain the uncertainty of output power near 10 times accurate in comparison with existing uncertainty calculation method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.1
• /
• pp.72-83
• /
• 2013

The paper proposes a new multilevel variable output voltage AC/DC Converter for power supply of power amplifiers used in underwater acoustic sensors. The proposed multilevel variable output voltage AC/DC Converter is composed of two parts. One as the input section is the high efficiency phase-shifted PWM full bridge DC-DC converter to get multiport power sources. The other as the output section is composed of two flying-capacitor 3-level DC-DC converters and a diode bridge circuit to get fast-response and multilevel variable output voltage for an envelope amplifier. Also the paper suggests the detailed circuit topology and design guideline of multilevel variable output voltage AC/DC converter. It also proposes the power balanced control method between 3-level converters and the voltage balanced algorithm for flying capacitors. Its characteristics should be verified by the detailed simulation results. It is anticipated that the proposed converter will be used very well for power amplifiers used in underwater acoustic sensors.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.6-12
• /
• 2010

In this paper, highly efficient class-F power amplifiers(PAs) with harmonic-controlling transmission lines(TLs) were built for cellular and WLAN applications at 840 MHz and 2.4 GHz each. Also, based on these single-band PAs, a dualband class-F PA was designed after a careful investigation into the harmonics of the two frequencies. The harmonic-controlling TL was designed for the class-F operation at dualband by switching the length of the shunt $\lambda$/4 TL part, while the series $\lambda$/4 TL is optimized for both frequencies. To verify the performance, two class-F PAs optimized at each frequency and a dualband class-F PA at the corresponding frequencies were built with the secondand the third-harmonic control circuits at each frequencies. As a result, the PA#1 at 840 MHz has a peak drain efficiency of 81.2 % with an output power of 24.4 dBm, while the PA#2 at 2.35 GHz shows a drain efficiency of 94.5 % with an output of 22.8 dBm. Finally, the dualband class-F PA#3 showed 60.5 % and 50.9 % drain efficiencies at 840 MHz and 2.4 GHz, with powers of 23.8 dBm and 19.62 dBm, respectively.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.4 no.3
• /
• pp.18-29
• /
• 1993

In single mode fiber optic transmission systems(FOT's) operated at high modulation rates over long fiber spans, chromatic dispersion can produce distortion in the demodulated waveforms, resulting in intersymbol interference(ISI) in the received signal and a reduction of transmission system performance. In this paper, chromatic dispersion limitations for intensity modulation and direct detection(IM-DD) systems are studied by considering the effect of phase modulation to amplitude modulation (PM-AM) conversion noise. Laser phase noise conversion to amplitude noise due to fiber chromatic dispersion is analyzed by deriving the noise power spectral density. We first derive the noise power spectral density of the laser phase noise to intensity noise conver- sion. Next, also evaluate the system power penalty and the transmitter laser linewidth required to avoid PM-AM conversion noise penalties in long-haul nonregenerative transmission system using an external modulator and optical amplifiers. For such system with optical amplifiers, transmission sys- tem length is limited due to fiber chromatic dispersion, even if an ideal external modulator is used.