• 한국응용과학기술학회지
• /
• 제31권4호
• /
• pp.731-739
• /
• 2014

투명 전도성 산화물로서 알루미늄과 붕소가 함께 도핑된 아연산화물(AZOB)이 $900^{\circ}C$에서 분무 열분해법에 의해 제조되었다. 얻어진 마이크론 크기의 AZOB 분말은 알루미늄, 붕소 및 아연의 수용액으로부터 얻어진다. 분무 열분해로 얻어진 마이크론 크기의 AZOB 분말은 $700^{\circ}C$에서 두 시간동안의 후 소성 과정과 24 시간 동안의 볼 밀링을 통해 나노 크기의 AZOB으로 변환된다. AZOB을 구성하는 일차 입자의 크기를 Debye-Scherrer 식에 의해 계산하였고 압축된 AZOB 펠렛의 표면 저항을 측정하였다.

• Korean Chemical Engineering Research
• /
• 제56권1호
• /
• pp.42-48
• /
• 2018

리튬이온전지의 음극재로 높은 이론적인 용량과 낮은 방전 전위 및 무독성을 가진 실리콘이 높은 관심을 받고 있다. 본 연구에서는 리튬이온전지의 고효율 음극재로 활용을 위한 실리콘-탄소나노튜브-탄소(Si-CNT-C) 복합체를 제조하였다. 복합체 제조를 위해서는 에어로졸 자기조립과 후 열처리 공정을 사용하였다. 제조된 Si-CNT-C 복합체는 구형이었으며 평균 입자크기는 $2.72{\mu}m$이었다. 복합체의 크기는 실리콘 및 탄소나노튜브의 농도가 증가할수록 커지는 것을 확인하였다. Si-CNT-C 복합체는 탄소나노튜브와 글루코스에서 탄화된 탄소가 실리콘 입자들을 중심으로 표면에 부착된 형태이었다. 제조된 Si-CNT-C 복합체는 전기화학 분석을 통해 순수한 실리콘보다 우수한 사이클 성능을 보여주고 있음을 확인하였다.

• 열처리공학회지
• /
• 제24권6호
• /
• pp.338-342
• /
• 2011

Ga doped ZnO (GZO) thin films were deposited with RF magnetron sputtering on glass substrate and then the effect of post deposition annealing at nitrogen atmosphere on the structural, optical and electrical properties of the films was investigated. The post deposition annealing process was conducted for 30 minutes at different temperature of 150, 300 and $450^{\circ}C$, respectively. As increase annealing temperature, GZO films show the increment of the prefer orientation of ZnO (002) diffraction peak in the XRD pattern and the optical transmittance in a visible wave region was also increased, while the electrical sheet resistance was decreased. The figure of merit obtained in this study means that GZO films which vacuum annealed at $450^{\circ}C$ have the highest optoelectrical performance in this study.

• 대한금속재료학회지
• /
• 제49권12호
• /
• pp.937-944
• /
• 2011

Studies have been carried out in order to reduce fuel-cladding chemical interaction (FCCI) behavior of metallic fuel in sodium-cooled fast reactors (SFR) using an electroplating technique. A $20{\mu}m$ thick Cr layer has been plated by the electrochemical method in the Sargent bath over the HT9 (12Cr-1Mo) clad material and diffusion couple tests of the U-10Zr metallic fuel as well as the rare earth alloy (70Ce-29La) have been conducted. The results show that the Cr plating can prevent FCCI behavior along the fuel-clad interface. However, cracks developed through the thickness during plating, which resulted in the migration of some fuel constituents. Variation of bath temperature, application of pulse current, and post heat treatment have been conducted to control such cracks. We found out that some conditions like the pulse current and the post heat treatment enhanced the layer property by reducing the internal cracks and improving the diffusion couple test.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.102-111
• /
• 2021

The corrosion behaviors of laser-welded super duplex stainless steel tubes with post-weld heat treatment(PWHT) conditions(950, 1000, 1050, 1100 ℃ for 5 and 30 min) were evaluated by electrochemical potentiodynamic polarization and critical pitting temperature measurements. This study showed that the critical metallurgical factors affecting the degradation of corrosion resistance of a steel tube in as-welded condition were the unbalanced phase fraction(ferrite:austenite = 94:4), Cr₂N precipitation, and phase transformation from the austenite phase to ɛ-martensite(via stress-induced phase transformation). The improvement in the corrosion resistance of the welded specimen depends greatly on the PWHT conditions. The specimens after PWHT conducted below 1000 ℃ showed inferior corrosion resistance, caused by precipitation of the sigma phase enriched with Cr and Mo. At 1100 ℃ for a longer duration in PWHT, the ferrite phase grows, and its fraction increases, leading to an unbalanced phase fraction in the microstructure. As a result, pitting can be initiated primarily at the interface between the ferrite/austenite phase, particularly in base metal.

• 한국결정성장학회지
• /
• 제31권2호
• /
• pp.78-83
• /
• 2021

본 연구에서는 수열반응법을 이용하여 3차원 구조를 갖는 NiCo2O4 입자를 합성했다. 수열합성에서 반응조건 [Ni]/[Co] 비율, 반응시간과 열처리온도를 달리하여 입자의 조성과 형상을 조절했다. 최적의 조건을 결정하고자 XRD, SEM을 통해 입자를 분석하였으며, [Ni]/[Co] 1:2 비율, 반응시간 12시간, 열처리 400℃ 4시간 조건에서 3차원 구조를 갖는 단일상의 NiCo2O4가 합성하였다. 합성된 NiCo2O4 나노구조체의 글루코스 센서 특성평가 결과, 글루코스에 대해 높은 민감도와 탁월한 선택성을 나타냈다. 본 연구를 통해 합성한 NiCo2O4 나노구조체는 향후 비효소 기반 전기화학적 글루코스 센서로 널리 응용될 수 있을 것으로 기대된다.

• 열처리공학회지
• /
• 제36권5호
• /
• pp.298-302
• /
• 2023

Transparent and conducting tungsten (W) doped indium oxide (IWO) thin films were deposited on the glass substrate by using RF magnetron sputtering and then electron irradiation was conducted to investigate the effect of electron irradiation on the optical and electrical properties of the films. The electron irradiated films showed three x-ray diffraction peaks of the In₂O₃ (222), (431) and (046) planes and the full width at half maximum values are decreased as increased electron irradiation energy. In the atomic force microscope analysis, the surface roughness of as deposited films was 1.70 nm, while the films electron irradiated at 700 eV, show a lower roughness of 1.28 nm. In this study, the figure of merit (FOM) of as deposited films is 2.07 × 10^-3 Ω^-1, while the films electron irradiated at 700 eV show the higher FOM value of 5.53 × 10^-3 Ω^-1. Thus, it is concluded that the post-deposition electron beam irradiation is the one of effective methods to enhance optical and electrical performance of IWO thin films.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.132-136
• /
• 2009

The importance and interests for saving of energy and cost in industry has been steadily grown up. Therefore, process optimization to reduce the processing step and energy is one of the most important things. The micro-alloyed steel of which post-heat-treatment is not necessary, has attractive points for high strength materials. However, for the application of non-heat-treated steel to structural parts, it is necessary to confirm the reliability of mechanical properties. In order to estimate mechanical properties. The microstructure, hardness, tensile strength, compressive strength and tensile fatigue strength of micro-alloyed steel having 900MPa tensile strength has been investigated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1018-1021
• /
• 2001

1018-1021 The CuO-P$_2$O$_{5}$ containing P$_2$O$_{5}$ as glass-former were prepared by press-quenching method on the copper plate. By post-heat treatment of these glasses, the CuO-P$_2$O$_{5}$ -V$_2$O$_{5}$ -g1ass ceramics was obtained and the crystallization behavior and dc conductivities were investigovted. The heat-treated glass-ceramics decreased in electrical conductivity by the order of 10$^1$ compared to amorphous glass. The linear relationship between In($\sigma$T) and T$^{-1}$ indicated that electrical conduction in CuO-P$_2$O$_{5}$ -V$_2$O$_{5}$ -gass occurred by a small polaron hopping.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.7-8
• /
• 2006

The effects of heat treatment on the electrical properties of SGOI were examined. We proposed the optimized heat treatments for improving the interfacial electrical properties in SGOI-MOSFET. By applying the additional pre-RTA(rapid thermal annealing) before gate oxidation and post-RTA after dopant activation, the driving current, the transconductance, and the leakage current were improved significantly.