• 전기전자학회논문지
• /
• 제24권1호
• /
• pp.67-71
• /
• 2020

본 연구에서와 같이 전동기의 저속 영역 운전의 센서리스 기법으로 적합한 고조파 주입 센서리스 제어기법의 시뮬링크 시뮬레이션 모델을 제안한다. 본 모델에 적용되는 전동기는 영구자석 전동기이다. 또한, 다양한 고조파 주입 기법중 1kHz 구형파를 주입하는 기법을 사용한다. 고조파 주입에 따른 전동기의 전동기 상수의 변화는 시뮬링크에서 제공하는 전동기의 상수조정을 통해 구현한다. 시뮬링크의 함수와 라이브러리에서 제공하는 모델을 통해 센서리스 기법을 구현한다. 전류에 포함된 고조파 성분을 필터를 이용하여 추출하고, 추출된 파형을 이용하여 영구자석 전동기의 각도를 검출함을 보인다. 그리하여 1kW 영구자석 전동기에 적용된 시뮬레이션 파형에서의 전동기 각도 추정파형과 전동기 제어관련 파형을 통해 시뮬레이션 모델의 타당성을 보인다.

• 전력전자학회논문지
• /
• 제18권3호
• /
• pp.205-210
• /
• 2013

This paper presents a novel hall sensor fault detection and fault-tolerant control method for a high-speed permanent magnet synchronous motor (PMSM) drive system. A phase locked loop (PLL) type position estimator is used with a conventional interpolation based rotor position estimator to reduce position errors due to misalignment of hall sensors. The expected trigger time of hall sensor's output is used for detecting hall sensor fault condition and the PLL type position estimator is reconfigured for fault-tolerant control at the hall sensor fault condition. The proposed method can minimize current ripples during the transition from sensored control using hall sensors to sensorless control. Experimental results have been proposed to prove the validity of the proposed method.

• 전력전자학회논문지
• /
• 제10권4호
• /
• pp.388-396
• /
• 2005

SRM은 각종 산업분야에서 토크 리플과 소음 진동, 낮은 역률로 인하여 실제 적용에는 어려움이 있고 구동을 하기 위해서는 회전자위치 정보를 위한 센서가 필요하다. 따라서 본 논문에서는 전압펄스 주입방식을 이용한 센서리스 방식을 제안하였다. 기존 전압펄스 주입방식의 문제점인 위상지연 문제와 기존 센서리스 방식의 어려움이라 할 수 있는 초기구동 문제를 제안하였다. 또한 고성능 마이크로프로세서를 사용한 복잡한 연산과정 없이 단순한 범용 아날로그 소자만으로도 간단히 센서리스 방식을 구현하였다.

• 전력전자학회논문지
• /
• 제16권1호
• /
• pp.71-78
• /
• 2011

본 논문에서는 영구자석 동기 전동기의 센서리스 운전에 있어, 제어에 사용되는 제정수의 오차가 각도 추정 성능에 미치는 영향을 분석하였다. 회전 자속의 위치를 추정하는데 사용되는 위치 오차 정보를 부호 요인과 이득 요인으로 나누어, 그 중에 각도 추정의 편차를 초래하는 부호 요인을 중심으로 제정수 오차가 각도 추정 성능에 미치는 영향을 분석하였다. 본 논문에서는 센서리스 제어에 사용되는 저항과 인덕턴스의 오차로 표현되는 각도 추정 편차의 함수를 수식적으로 도출하였고, 모의실험 및 실험을 통해 도출된 수식의 타당성을 검증하였다.

• Journal of Power Electronics
• /
• 제9권3호
• /
• pp.499-506
• /
• 2009

In this paper, the initial pole-position estimation of a surface (non-salient) permanent magnet synchronous motor is mathematically analyzed and surveyed on the basis of simulation analysis, and developed for accurate servo motor drive. This algorithm is well carried out under the full closed-loop position control without any pole sensors and is completely insensitive to any motor parameters. This estimation is based on the principle that the initial pole-position is simply calculated by the reverse trigonometric function using the two feedback currents in the full closed-loop position control. The proposed algorithm consists of the predefined reference position profile, the information of feedback currents, speed, and relative position, and the reverse trigonometric function for the initial-pole position estimation. Comparing with the existing researches, the mathematical analysis is introduced to get a more accurate initial pole-position of the surface permanent magnet motor under the closed-loop position control. It is found that the proposed algorithm can be easily applied in servo drive applications because it satisfies the following user's specifications; accuracy and moving distance.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.157-164
• /
• 2000

This paper presents a method to detect a rotor position and to drive a BLDC motor from standstill to medium speed without any position sensor comparing the current responses due to the inductance variation in the rotor position. A rotor position at a standstill is identified by the current responses of six pulses injected to each phase of a motor. Once the motor stars up pulse train that is composed of long and short pulses is injected to the phase corresponding to produce the maximum torque and the next phase continuously. it provides not only the torque but also the information of the next commutation time effectively when the response of long and short pulses crosses each other after the same time delay. This method which is verified experimentally using a DSP can drive a BLDC motor to the medium speed smoothly without any rattling and time delay compared with the conventional sensorless algorithm.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.179-183
• /
• 1999

This paper describes a new method for indirect sensing of the rotor position in switched reluctance motors using fuzzy logic algorithm. Through a novel fuzzy algorithm, the complete SRM magnetizing characterization is first constructed, and then used to estimate the rotor position. And also, the optimized phase is selected by phase selector. To demonstrate the promise of this approach, the proposed rotor position estimation algorithm is simulated for variable speed range.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.934-935
• /
• 2015

This paper presents the sensorless control method that employs the adaptive back-EMF(Electromotive Force) and current model observer of interior permanent magnet synchronous motor(IPMSM). The estimated back EMF considering a saliency is obtained by using the adaptive control method. The estimated EMF is inputted to the current model observer which is connected in series with adaptive back EMF estimator and is used to estimate the position and speed of the rotor. In order to improve the shortcomings of conventional method using the current error components multiplied in the compensation constant, the modified instantaneous reactive power compensator is applied. The validity of the control system presented is verified by the simulation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 추계학술대회
• /
• pp.259-260
• /
• 2010

This paper presents the sensorless and MPPT control algorithm for a 100kW tidal energy system. The proposed algoritm is estimated the rotor position and generator speed using adaptive sliding mode observer. The vector control of generator at the machine side converter and the converter at the grid side are controlled to obtain maximum torque and to regulate unity power factor respectively. Psim simulation is used for validity of proposed control algorism.