• 한국재료학회지
• /
• 제27권11호
• /
• pp.631-635
• /
• 2017

We report facile solution processing of mesoporous hematite (${\alpha}-Fe_2O_3$) thin films for high efficiency solar-driven water splitting. $Fe_2O_3$ thin films were prepared on fluorine doped tin oxide(FTO) conducting substrates by spin coating of a precursor solution followed by annealing at $550^{\circ}C$ for 30 min. in air ambient. Specifically, the precursor solution was prepared by dissolving non-toxic $FeCl_3$ as an Fe source in highly versatile dimethyl sulfoxide(DMSO) as a solvent. The as-deposited and annealed thin films were characterized for their morphological, structural and optical properties using field-emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS) and UV-Vis absorption spectroscopy. The photoelectrochemical performance of the precursor (${\alpha}-FeOOH$) and annealed (${\alpha}-Fe_2O_3$) films were characterized and it was found that the ${\alpha}-Fe_2O_3$ film exhibited an increased photocurrent density of ${\sim}0.78mA/cm^2$ at 1.23 V vs. RHE, which is about 3.4 times higher than that of the ${\alpha}-FeOOH$ films ($0.23mA/cm^2$ at 1.23 V vs. RHE). The improved performance can be attributed to the improved crystallinity and porosity of ${\alpha}-Fe_2O_3$ thin films after annealing treatment at higher temperatures. Detailed electrical characterization was further carried out to elucidate the enhanced PEC performance of ${\alpha}-Fe_2O_3$ thin films.

• Korean Chemical Engineering Research
• /
• 제54권2호
• /
• pp.157-162
• /
• 2016

다공성 $Co(OH)_2$ 나노플레이크 박막은 전위제어 전착법을 이용하여 티타늄 메쉬에 여러 전착전위(-0.75, -1.0, -1.2 및 -1.4 V)에서 전착하여 슈퍼커패시터에 이용하였다. 티타늄 메쉬에 전착된 $Co(OH)_2$ 나노플레이크 박막의 두께 및 전착량은 전착전위의 제어에 의해 결정되었고 -1.4 V에서 전착한 $Co(OH)_2$ 나노플레이크 박막의 두께는 약 $34{\mu}m$로 가장 두껍게 전착되었으며 전착량은 17.2 g이다. 전착전위 -0.75, -1.0, -1.2 및 -1.4 V에서 전착한 경우 초기 방전용량은 각각 226, 370, 720 그리고 $1,008mF\;cm^{-2}$으로 나타났고 1,000 사이클 후 각각 206, 349, 586 그리고 $866mF\;cm^{-2}$으로 나타났다. 또한 이들의 용량유지율은 각각 91, 94, 81 및 86%로 나타났다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.423.1-423.1
• /
• 2016

Polyvinylidene fluoride (PVDF) has drawn much attention due to its many advantages. PVDF shows high mechanical strength and flexibility, thermal stability, and good piezoelectricity enabling its application to various fields such as sensors, actuators, and energy transducers. Further studies have been conducted on PVDF in the form of thin films. The thin films exhibit different ionic conductivity according to the number of pores within the film, letting these films to be applied as electrolytes or separators of batteries. Porous PVDF membranes are also easily processed, usually made by using electrospinning. However, a large portion of researches were conducted using PVDF membranes produced by far field electrospinning, which is not a well-controlled experimental method. In this paper, we use near field electrospinning (NFES) process for more controlled, small-scaled, mesh type PVDF structures of nano to micro fibers fabricated by controlling process parameters and investigate the properties of such membranous structures. These membranes vary according to geometrical shape, pore density, and fiber thickness. We then measured the mechanical strength and piezoelectric characteristic of the structures. With various geometries in the fiber structures and various scales in the fibers, these types of structures can potentially lead to broader applications for stretchable electronics and dielectric electro active polymers.

• 한국세라믹학회지
• /
• 제56권2호
• /
• pp.130-145
• /
• 2019

Widespread commercialization of solid oxide fuel cells (SOFCs) is expected to be realized in various application fields with the advent of cost-effective fabrication of cells and stacks in high volumes. Cost-reduction efforts have focused on production yield, power density, operation temperature, and continuous manufacturing. In this article, we examine several issues associated with processing for SOFCs from the standpoint of the bimodal packing model, considering the external constraints imposed by rigid substrates. Optimum compositions of composite cathode materials with high volume fractions of the second phase (particles dispersed in matrix) have been analyzed using the bimodal packing model. Constrained sintering of thin electrolyte layers is also discussed in terms of bimodal packing, with emphasis on the clustering of dispersed particles during anisotropic shrinkage. Finally, the structural transition of dispersed particle clusters during constrained sintering has been correlated with the structural stability of thin-film electrolyte layers deposited on porous solid substrates.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1998년도 추계 총회 및 학술발표회
• /
• pp.63-65
• /
• 1998

1. Introduction : Atmospheric discharge of VOC-contaminated streams in chemical plants and air streams from chemical processes poses a serious environmental problem and entails large financial losses. Such emissions may be reduced by i) adsorption process, ii) absorption process and iii) incineration process. These processes only forbids the air pollutions. Throughout the recent decade, another technique-membrane process has emerged. The separation and recovery of organic vapors by membrane process may have great economic potential. Most of the published research works on the separation of organic vapors from air were performed using silicon rubber membranes. However, it is very difficult to fabricate very thin membranes with less than 1 $u m thickness. Plasma polymerization could be a good technique to generate a thin polymer film. The objective of this work is to find out the optimum condition of plasma polymerization for producing VOC separation membrane. For the objective, composite membranes are prepared through plasma polymerization of hexamethyldisiloxane onto porous substrates under different conditions. The membrane is then subjected to the permeation of permanent gases and VOCs to find the correlations between the physical properties of the penetrant and permeability and selectivity.

• Current Photovoltaic Research
• /
• 제10권2호
• /
• pp.39-48
• /
• 2022

A Se-containing Cu/SnSe₂/ZnSe precursor was employed to introduce S to the precursor to form Cu₂ZnSn(S,Se)₄ (CZTSSe) film. The morphology of CZTSSe films strongly varied with two different pre-annealing environments: S and N₂. The CZTSSe film with S pre-annealing showed a dense morphology with a smooth surface, while that with N₂ pre-annealing showed a porous film with a plate-shaped grains on the surface. CuS and Cu₂Sn(S,Se)₃ phases formed during the S pre-annealing stage, while SnSe and Cu₂SnSe₃ phases formed during the N₂ pre-annealing stage. The SnSe phase formed during N₂ pre-annealing generated SnS₂ phase that had plate shape and severely aggravated the morphology of CZTSSe film. The power conversion efficiency of the CZTSSe solar cell with S pre-annealing was low (1.9%) due to existence of Zn(S.Se) layer between CZTSSe and Mo substrate. The results indicated that S pre-annealing of the precursor was a promising method to achieve a good morphology for large area application.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.477-484
• /
• 1994

The yttria stabilized zirconia(YSZ) thin films for solid oxide fuel cell (SOFC) were fabricated by an electrochemical vapor deposition(EVD) technique using YCl3+ZrCl4+H2O gas system. The YSZ films were deposited under reduced pressure at the temperature of 1000~120$0^{\circ}C$ on the porous alumina substrates. The deposition rate, chemical composition and growth morphology were investigated by SEM, XRD, EDS. The growth rates of the films obeyed a parabolic rate law, representing that the growing process is controlled by an electrochemical transport through the YSZ film. The Y2O3 content of the films was about 10 mol%, equal to the composition of metal chloride reactant gases, approximately. The YSZ films were highly dense, the growing features showed columnar structure and surface morphologies were changed with the EVD conditions.

• 한국세라믹학회지
• /
• 제45권12호
• /
• pp.782-787
• /
• 2008

Ni-ceria cermets have been extensively investigated as candidates for the anode in intermediate-temperature solid oxide fuel cells. We have used the citric method to synthesize nanocomposite powders consisting of NiO (Ni metal content: $40{\sim}60%$ by volume) highly dispersed in $Ce_{0.9}Gd_{0.1}O_{1.95}$ (CGO). The microstructure characteristics and sintering behaviors of the nanocomposites were investigated. No impurity phases were observed and the shrinkage of these substrates matched well with that of a CGO electrolyte with a specific surface area of $11\;m^2/g$. Densification of the CGO electrolyte layer to $<5\;{\mu}m$ thickness was achieved by co-firing the laminated electrolyte with the porous NiO-CGO substrate at $1400^{\circ}C$ for 6 h.

• 전기학회논문지
• /
• 제58권12호
• /
• pp.2474-2479
• /
• 2009

This paper presents an atmospheric microplasma-jet device for bio~medical application. The microplasma-jet device consists of four components; a thin Ni anode, porous alumina insulator, a stainless steel cathode and an aluminum case. The anode has 8 holes, and hole diameter and depth are $200 {\mu}m$ and $60 {\mu}m$, respectively. The discharge test was performed in atmospheric pressure using nitrogen gas and AC voltage at the optimum gas flow rate of 4 Vmin. The plasma-jet is ejected stably for the input voltage ranging from 5.5 to $9.5 kV_{p-p}$. The plasma becomes dense as the input voltage increases, which was verified by the hydrophilicity change of PMMA surface treated by the plasma. The temperature increasement of the aluminum film exposed to plasma-jet illustrates that the micro plasma-jet device is feasible for bio-medical application.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.372-372
• /
• 2007

Titanium oxide nanotube arrays were fabricated by the anodization of pure titanium thin film deposited at $500^{\circ}C$ on silicon substrates. The titania nanotubes were grown by anodization in nonaqueous-base electrolytes at different potentials between 5 V and 30 V. $TiO_2$ nanotube array with a small pore diameter of 40 nm and long titanium oxide layer of $4\;{\mu}m$ was obtained. The $TiO_2$ nanotube array was used as a porous electrode for quartz crystal microbalance (QCM). Nanoporous morphology of electrode will increase the sensitivity of microbalance.