• 공업화학
• /
• 제32권4호
• /
• pp.403-408
• /
• 2021

본 논문에서는 얇고 유연한 평면 슈퍼 커패시터(PSC)를 스크린 인쇄된 탄소 전극에 폴리아닐린(PANI)을 코팅하여 제작하였습니다. 스크린 프린팅 방법을 사용하여 유연한 폴리에틸렌 테레프탈레이트에 탄소 잉크를 코팅한 후 희석 중합 법을 사용하여 탄소 표면에 PANI 박막을 코팅하였습니다. 서로 맞물린 구조의 얇은 유연한 PANI 전극을 폴리머겔 전해질로 조립하여 평면 모양의 슈퍼 커패시터(PSC) 장치를 만들었습니다. 상기 제조된 PANI/PSC는 매우 얇고 유연 하였으며, 10 mV/s에서 409 µF/cm²의 높은 면적 정전용량을 나타내었습니다. 이 값은 500 mV/s에서 원래 값의 46%로 유지되었습니다. 유연한 PANI/PSC는 180°의 구부러진 상태와 100번째의 반복적인 피로도 테스트에서도 82%의 높은 정전 용량 유지를 보여주었습니다.

• ETRI Journal
• /
• 제26권6호
• /
• pp.583-588
• /
• 2004

In this paper we investigate the effect of a shield metal line inserted between adjacent bit lines on the refresh time and noise margin in a planar DRAM cell. The DRAM cell consists of an access transistor, which is biased to 2.5V during operation, and an NMOS capacitor having the capacitance of 10fF per unit cell and a cell size of $3.63{\mu}m^2$. We designed a 1Mb DRAM with an open bit-line structure. It appears that the refresh time is increased from 4.5 ms to 12 ms when the shield metal line is inserted. Also, it appears that no failure occurs when $V_{cc}$ is increased from 2.2 V to 3 V during a bump up test, while it fails at 2.8 V without a shield metal line. Raphael simulation reveals that the coupling noise between adjacent bit lines is reduced to 1/24 when a shield metal line is inserted, while total capacitance per bit line is increased only by 10%.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.160-168
• /
• 2003

The co-firing processes for the supported type planar solid oxide fuel cell were investigated. A flat cell of $7.7${\times}$10.8\textrm{cm}^2$ was fabricated successfully by the co-firing process, in which green films were co-sintered in the forms of two layers of anode/electrolyte or of three layers of anode/electrolyte/cathode with gas distributor. A co-fired cell of two layers yielded a power of 200 ㎽/$\textrm{cm}^2$ at 608 ㎷. Its performance loss was mainly due to iR drop in the anodic gas distributor, which was attributed to poor contact between anodic gas distributor and current collector. The performance in the co-fired cell of three layers was much lower than that of two layers, which resulted from the large iR drop and activation overvoltage at the cathodic side. In the co-fired cell of two layers, the impedance analysis indicated that the performance decay during cell operation is due to both anode overvoltage and iR drop at anode side. Also the electrode reaction of the co-fired two layers' cell is considered to be controlled by activation overvoltage within the low current of 50 ㎃.

• International Journal of Aeronautical and Space Sciences
• /
• 제14권1호
• /
• pp.85-90
• /
• 2013

This paper presents a study on terrain referenced navigation (TRN). The extended Kalman filter (EKF) is adopted as a filter method. A Jacobian matrix of measurement equations in the EKF consists of terrain slope terms, and accurate slope estimation is essential to keep filter stability. Two slope estimation methods are proposed in this study. Both methods are based on the least-squares approach. One is planar regression searching the best plane, in the least-squares sense, representing the terrain map over the region, determined by position error covariance. It is shown that the method could provide a more accurate solution than the previously developed linear regression approach, which uses lines rather than a plane in the least-squares measure. The other proposed method is weighted planar regression. Additional weights formed by Gaussian pdf are multiplied in the planar regression, to reflect the actual pdf of the position estimate of EKF. Monte Carlo simulations are conducted, to compare the performance between the previous and two proposed methods, by analyzing the filter properties of divergence probability and convergence speed. It is expected that one of the slope estimation methods could be implemented, after determining which of the filter properties is more significant at each mission.

• 한국전자파학회논문지
• /
• 제24권3호
• /
• pp.233-238
• /
• 2013

본 논문은 다이버시티 모드와 지향성 모드를 스위치 할 수 있는 평면형 안테나 구조를 제안하였다. 제안된 구조는 네 개의 안테나 요소들을 한 평면에 배열했을 경우, 높은 격리도를 가지며 다이버시티 모드로 동작한다. 한편, 네 개의 안테나 요소들을 수직으로 적층 배치한 구조는 지향성 모드로 동작한다. 이 경우, 네 개의 안테나 요소들은 적층형 Yagi-Uda 안테나 구조를 따르며, 높은 이득을 갖도록 최적화되었다. 특히, 네 개의 안테나 요소에 두 가지의 급전 방법과 구부러진 급전선을 사용하여 성능을 극대화 시켰다. 2.4 GHz에서 동작하는 제안된 안테나는 시뮬레이션 결과와 실험적인 결과가 일치하는 것을 확인하였으며, 각 모드에서의 성능 또한 입증하였다.

• 한국산학기술학회논문지
• /
• 제15권4호
• /
• pp.2330-2334
• /
• 2014

본 논문에서는 무선 신호전송을 위한 비접촉 방식의 AC커플링(Coupling)기반 평면 나선형 인덕터의 주파수 특성을 분석하였다. 기판의 유전상수의 변화는 소자의 인덕턴스에 직접적인 영향을 주지 않고 소자의 전기용량에 영향을 주어 공진주파수를 변화시키는 것을 알 수 있다. 기판의 두께가 증가할수록 인덕턴스는 증가하지만 공진주파수는 감소하였으며, 이것은 기판 두께의 감소로 인해 내부 전기용량이 증가하였기 때문이다. 인덕터의 도체 선 폭이 증가하여도 전체 인덕터 크기와 턴 수 및 선 간격이 일정함으로 내부 사각 코일의 도선 면적이 작아지게 되어 각각의 자기 인덕턴스가 감소하게 되고 공진주파수는 증가되게 된다. 또한, 도체의 선 간격이 증가하면 내부 사각 코일의 도선 면적이 작아지게 된다.

• 대한기계학회논문집A
• /
• 제21권1호
• /
• pp.104-111
• /
• 1997

Accounting for the additional damages come out from non-proportional loading path effect, material damage according to crystal structure dependence was studied. Microscopic observations of damaged material by SEM(Scanning Electron Microscope) showed crystal structure dependence. Biaxial in-phase loaded specimens showed the slips of same direction, which pararell each other, but biaxial 90.deg. out-of-phase loaded specimens showed multiply crossed slips. S. H. Doong and D. F. Socie reported that wavy/planar or planar slip material showed the increase in the cyclic hardening level during non-proportional cycling. From these results, the additional hardening and non-proportional loading effects were related with slip mechanism, and the slip mechanism was related with crystal structure. In the present study, a damage mechanism which accounts for the non-proportional loading effect from crystal structure dependence was considered and applied to A17075-T651.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.10-14
• /
• 2014

In this study, we fabricate an integrated microfluidic chip with a planar Hall effect (PHE) sensor for single magnetic bead detection. The PHE sensor was constructed with a junction size of $10{\mu}m{\times}10{\mu}m$ using a trilayer structure of Ta(3 nm)/NiFe(10 nm)/Cu(1.2 nm)/IrMn(10 nm)/Ta(3 nm). The sensitivity of the PHE sensor was 19.86 ${\mu}V/Oe$. A diameter of 8.18 ${\mu}m$ magnetic beads was used, of which the saturation magnetization was ~2.1 emu/g. The magnetic susceptibility ${\chi}$ of these magnetic beads was calculated to be ~0.14. The diluted magnetic beads solution was introduced to the microfluidic channel attributing a single bead flow and simultaneously the PHE sensor voltage was measured to be 0.35 ${\mu}V$. The integrated microchip was able to detect a magnetic moment of $1.98{\times}10^{-10}$ emu.

• 대한기계학회논문집B
• /
• 제24권1호
• /
• pp.93-101
• /
• 2000

The characteristics of spray nozzle have been quantified with the measurement of fluorescence and Mie scattering images. To correct the attenuation of the incident light sheet, a sequential double-pass light sheet system and the geometrical averaging of two images was implemented. Quantitative mass flux distribution of spray was obtained from fluorescence image. 3-D image is reconstructed using 2-D radial images. Sauter mean diameter (SMD) distribution was determined using the ratio of fluorescence signal intensity and Mie scattering signal intensity and the values were quantified with PDP A data. The measurement of mass flux and SMD using planar imaging technique agee with PDP A data fairly well in the low density region. However, in dense region， there are significant errors caused by secondary scattering. It was found that the planar imaging technique provides many advantages over the point measurement technique, such as PDP A, and can be implemented for quantitative measurement, especially in low density region.

• 센서학회지
• /
• 제6권3호
• /
• pp.237-244
• /
• 1997

A new planar-type microsensor, which had a platinum heater and a sensing layer on the same plane was fabricated on silicon substrate with stress-relieved PSG(phosphosilicate glass)/$Si_{3}N_{4}$(800nm/150nm) diaphragm. The proposed planar-type microsensor could be fabricated by simple silicon process using only 3 masks for photolithography process compared with 5 or 6 masks of the typical micro-gas sensor. The thermal properties of the microsensor from thermal simulation were compared with those of the fabricated microheater. Although there are some discrepancy between the simulation result and the result from the fabricated microheater, the thermal simulation by FEM was proved to be an useful method to evaluate the thermal properties of microheater. The sensing characteristics of the fabricated microsensor with the planar-type heater were investigated also.