• 한국산학기술학회논문지
• /
• 제13권3호
• /
• pp.1002-1007
• /
• 2012

Pillar의 제조 방법은 진공유리 및 반도체 디스플레이 분야에서 사용되는 핵심공정 중 하나이다. Pillar는 스크린 인쇄 방식을 통하여 배치할 수 있으나 시료의 성분에 따라 메탈마스크의 패턴을 전부 통과하지 못하거나 점도에 따라 통과된 혼합물이 본래의 형상을 유지 못하는 경우가 발생한다. 본 연구에서는 알루미나와 실리카 기반의 무기화합물을 이용하여 스크린 인쇄를 통해 pillar를 배치하였다. 실험계획법의 하나인 혼합물 설계를 이용함으로써 실험횟수를 줄이고 진공유리 pillar의 조성을 설계할 수 있는 방법을 제시하고자 한다.

• Design & Manufacturing
• /
• 제15권2호
• /
• pp.17-22
• /
• 2021

The shape of the blank greatly affects the formability and quality of the product after the stamping process. In this study, the geometry of the B-Pillar blank in the stamping process was optimized using design of experiments. The geometry of the blank for the B-pillar was simplified with the two length values and two radius values. The effects of design variables were studied through the Design of experiments. The stamping process of the B-pillar was predicted with the Finite Element Analysis (FEA). The optimized blank geometry was obtained. It results in the reduced maximum equivalent plastic strain. The local necking and the wrinkling did not occurred with the optimized blank geometry.

• 소음진동
• /
• 제5권3호
• /
• pp.395-402
• /
• 1995

In general low frequency vibration characteristics like an idleshake is mainly influeced by pillar section properties and joints. So the design technique development of vehicle pillar structures is required to initial design and vehicle development stage. In this paper to develop pillar structure design technique considering low frequency vibration characteristics, strain energy method, design sensitivity analysis method, and design optimization method using commercial finite element analysis program and optimization program are presented.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.107-113
• /
• 2004

This paper presents the pillar section optimization technique considering the reliability of the vehicle body structure consisted of complicated thin-walled panels. The response surface method is utilized to obtain the response surface models that describe the approximate performance functions representing the system characteristics on the section properties of the pillar and on the mass and the natural frequencies of the vehicle B.I.W. The reliability-based design optimization on the pillar sections Is performed and compared with the conventional deterministic optimization. The FORM is applied for the reliability analysis of the vehicle body structure. The developed optimization system is applied to the pillar section design considering the fundamental natural frequencies of passenger car body structure. By applying the proposed RBDO technique, it can be possible to optimize the pillar sections considering the reliability that engineers require.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.84-92
• /
• 2005

This paper is concerned with optimum design of a center-pillar assembly induced by the high-speed side impact of the vehicle. In order to simulate deformation behavior of the center-pillar assembly, simplified finite element model of the center-pillar and a moving deformable barrier are developed based on results of the crash analysis of a full vehicle model. In optimization of the deformation shape of the center-pillar, S-shaped deformation is targeted to guarantee reduction of the injury level of a driver dummy in the crash test. Tailor-welded blanks are adopted in the simplified center-pillar model to control the deformation shape of the center-pillar assembly. The thickness of each part which constitutes the simplified model is selected as a design parameter. The thickness of parts which have significant effect on the deformation mechanism are selected as design parameters with sensitivity analysis based on the design of experiment technique. The objective function is constructed so as to minimize the weight and lead to an S-mode deformation shape. The result shows that the simplified model can be utilized effectively for optimum design of the center-pillar members with remarkable saving of computing time.

• 한국전기전자재료학회논문지
• /
• 제26권6호
• /
• pp.434-440
• /
• 2013

With polymer properties and ceramic volume fraction as design variables, the optimal structure of 1-3 piezocomposites has been determined to maximize the thickness mode electromechanical coupling factor. When the piezocomposite vibrates in a thickness mode, inter-pillar resonant modes are likely to occur between lattice-structured piezoceramic pillars and polymer matrix, which significantly deteriorates the performance of the piezocomposite. In this work, a new method to design the structure of the 1-3 type piezocomposite is proposed to maximize the thickness mode electromechanical coupling factor while preventing the occurrence of the inter-pillar modes. Genetic algorithm was used for the optimal design, and the finite element analysis method was used for the analysis of the inter-pillar mode.

• Geomechanics and Engineering
• /
• 제28권5호
• /
• pp.463-475
• /
• 2022

In the mine exploitation stage; one of the critical issues is the stability assessment of post-pillars. The instability of post-pillars leads to serious safety hazards in mining operations. The focus of this study is to assess the stability of post-pillars in the 130# stope in the central ore body at Trepça hard rock mine by employing both conventional (i.e., critical span curve) and numerical methods (i.e., FLAC3D). Moreover, a new numerical based index (i.e., Pillar Yield Ratio-PYR) was proposed. The aim of PYR index is to determine a border line between stable, potentially unstable, and failure state of post-pillars at a specific mine site. The critical value of pillar width to height ratio is 2.5 for deep production stopes (e.g., > 800 m). Results showed that pillar size, mining height and mining depth significantly have affected the post-pillar stability. The reliability of numerical based index (i.e., PYR) is verified based on empirical underground pillar stability graph developed by Lunder, 1994. The proposed pillar yield ratio index and pillar stability graph can be used as a design tool in new mining areas at Trepça hard rock mine and for other situations with similar geotechnical conditions.

• 터널과지하공간
• /
• 제24권5호
• /
• pp.335-343
• /
• 2014

무지보 암주에 의해 채굴적의 안정성을 확보하는 주방식 채광법은 전 세계적으로 가장 일반적이며 널리 활용되고 있는 지하 채광법이다. 경제적이고 운용 중에 확장이 가능한 주방식 채광법을 지하공간 건설에 적용하기 위한 기초 연구로서, 본 연구에서는 주방식 지하구조에서 가장 중요한 무지보 암주의 설계방법을 고찰하고 주요 설계변수들에 대한 총 125개 조건의 변수해석을 실시하였다. 이상의 연구결과, 암주의 폭과 암주의 안전율은 매우 뚜렷한 선형관계를 보이며, 암석의 압축강도가 동일할 경우에는 공간 폭과 암주 폭의 비율이 증가할수록 무지보 암주의 안전율이 음지수 함수 형태로 감소하는 것으로 나타났다. 또한 변수해석 결과들을 바탕으로, 암석의 압축강도와 설계 안전율에 따라 무지보 암주의 설계 형상변수를 쉽게 추정할 수 있는 도표를 제시하였다.

• 한국터널지하공간학회 논문집
• /
• 제15권6호
• /
• pp.585-597
• /
• 2013

본 연구에서는 주방식 지하구조물의 안정성 검토방안을 마련하기 위해 암주와 천장부의 거동을 수치해석 방법으로 검토하였다. 또한, 기존 자원개발 분야에서 고려하는 주방식 공법의 설계 개념과는 달라져야 하는, 공간 확보차원에서의 합리적인 주방식 공법의 설계 절차 및 개념을 제시하였다. 주어진 지반 조건에서 암주의 형상비와 천장부의 길이에 따른 수치해석을 수행하였으며 초기 이완이 시작되는 시점에서의 파괴유형과 위치 변화를 검토하였다. 해석결과, 천장부 폭과 암주 폭과의 비(w/s)와 파괴시점의 상재하중간의 관계는 선형관계를 보였으며, 천장부 폭과 암주 폭의 비가 주방식 채광 설계에서는 매우 중요한 설계인자로 다루어지는 암주의 폭과 높이 비(w/H)보다 구조물의 안정성 확보차원에서는 더욱 민감한 설계인자인 것으로 나타났다. 이는, 암주의 안정성 만을 확보하는 차원에서 수행되는 주방식 채광 설계법과는 달리, 암주부와 함께 구조물 천장부 및 어깨부의 안정성까지도 함께 고려하여 지하구조물의 안정성을 확보할 수 있는 구조물 설계가 되어야 함을 의미한다. 또한, 지하구조물의 형상에 따라 초기 이완대가 발생하는 위치와 전단 또는 인장파괴 등 파괴유형도 다르게 나타나, 주방식 지하구조물에 대한 설계는 상재하중에 따른 천장부와 암주의 안정성을 연계하여 수행하는 것이 필요하다.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.99-106
• /
• 2001

NHTSA has been conducting biomechanical studies to reduce inujuries sustained sustained during automotive collision. Furthermore, NHTSA added the regulation to the FMVSS 201, limiting the equivalent HIC(Head Injury Criterion) value under 1000. In the presont work, a methodology was developed for the optimum design of the A-pillar trim with rib-structures. The design variables for the rib-strucrures were the transverse spacing, the longitudinal spacing, and the thickness. The required sets of the design varibles were decided based on the design of experiments. The head impact simulations were carried out using the LS-DYNA3D, and the HIC(d) values were computed using the resulrs of the head impact simulation. The objective function was constructed using the response surface methed (RSM). When the obtained optimum values were not inside the region of interest, the design proceduers were repeated by changing the region of interest. Finally, an A-pillar trim with rib-structures, which resulred in HIC(d) value under 850 for 15 mph head-trim impact, was developed.