• 한국재료학회지
• /
• 제28권11호
• /
• pp.611-614
• /
• 2018

Laminate composites composed of $0.95Pb(Zr_{0.52}Ti_{0.48})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3$ piezoelectric ceramic and Fe-Si-B based magnetostrictive amorphous alloy are fabricated, and the effect of control of the areal dimensions and the thickness of the piezoelectric layer on the magnetoelectric(ME) properties of the laminate composites is studied. As the aspect ratio of the piezoelectric layer and the magnetostrictive layer increases, the maximum value of the ME voltage coefficient(${\alpha}_{ME}$) increases and the intensity of the DC magnetic field at which the maximum ${\alpha}_{ME}$ value appears decreases. Moreover, as the thickness of the piezoelectric layer decreases, ${\alpha}_{ME}$ tends to increase. The ME composites exhibit ${\alpha}_{ME}$ values higher than $1Vcm^{-1}Oe^{-1}$ even at the non-resonance frequency of 1 kHz. This study shows that, apart from the inherent characteristics of the piezoelectric composition, small thicknesses and high aspect ratios of the piezoelectric layer are important dimensional determinants for achieving high ME performance of the piezoelectric-magnetostrictive laminate composite.

• 한국전기전자재료학회논문지
• /
• 제20권10호
• /
• pp.869-872
• /
• 2007

In this study, in order to develop low temperature sintering ultrasonic nozzle, single-layer and multilayer ring-type piezoelectric actuators were manufactured using PMN-PNN-PZT ceramics, And then the electrical properties were investigated. A ring-type piezoelectric actuator was modeled by ATILA program using finite element method(FEM). The piezoelectric actuator dimension was $\Phi26.5$ (outer diameter), $\Phi12$ (inner diameter), 3.5 mm (thickness). By FEM analysis, resonant and anti-resonant frequencies were appeared as 56.7 kHz and 61.5 kHz. The displacement increased with the increases of the number of layer. Based on the result, ring-type multilayer piezoelectric actuators were manufactured at low co-firing temperature of $940^{\circ}C$. The resonant resistance decreased with the increases of the number of layer. And also, the capacitance increased with the increases of the number of layer. The mechanical quality factor (Qm) decreased with the increases of the number of layer.

• Smart Structures and Systems
• /
• 제16권5호
• /
• pp.891-918
• /
• 2015

In many of microdevices a part of a microbeam is covered by a piezoelectric layer. Depend on the application a DC or AC voltage is applied between upper and lower side of the piezoelectric layer. A common method in many of previous works for evaluating the response of these structures is discretizing by Galerkin method. In these works often single mode shape of a uniform microbeam i.e. the microbeam without piezoelectric layer has been used as comparison function, and so the convergence of the solution has not been verified. In this paper the Galerkin method is used for discretization, and a comprehensive analysis on the convergence of solution of equation that is discretized using this comparison function is studied for both clamped-clamped and clamped-free microbeams. The static and dynamic solution resulted from Galerkin method is compared to the modal expansion solution. In addition the static solution is compared to an exact solution. It is denoted that the required numbers of uniform microbeam mode shapes for convergence of static solution due to DC voltage depends on the position and thickness of deposited piezoelectric layer. It is shown that when the clamped-clamped microbeam is coated symmetrically by piezoelectric layer, then the convergence for static solution may be obtained using only first mode. This result is valid for clamped-free case when it is covered by piezoelectric layer from left clamped side to the right. It is shown that when voltage is AC then the number of required uniform microbeam shape mode for convergence is much more than the number of required mode in modal expansion due to the dynamic effect of piezoelectric layer. This difference increases by increasing the piezoelectric thickness, the closeness of the excitation frequency to natural frequency and decreasing the damping coefficient. This condition is often indefeasible in microresonator system. It is concluded that discreitizing the equation of motion using one mode shape of uniform microbeam as comparison function in many of previous works causes considerable errors.

• Computational Structural Engineering : An International Journal
• /
• 제3권1호
• /
• pp.49-59
• /
• 2003

This paper discusses the enhancement of the buckling capacity of column strips by use of piezoelectric layer. The analytical model for obtaining the buckling capacity of the piezoelectric coupled column with general boundary conditions modelled with different types of springs applied at the ends of the column is derived the first time. Based on this proposed model, the buckling capacity of the column strips can be accurately predicted by solving an eigenvalue problem. The computational results show the great potential of the piezoelectric materials in enhancing the buckling capacity of the column strips. The optimal locations of the piezoelectric layer for higher buckling capacity are also obtained for the columns with. standard pinned-pinned, fixed-free, and fixed-pinned structures. In addition, the buckling capacity and the increase of buckling capacity are discussed for those columns with the general boundaries as well. This research may provide a benchmark for the buckling analysis of the piezoelectric coupled strips.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권9호
• /
• pp.495-501
• /
• 2000

This paper presents a method to minimize the initial deflection of a multi-layer piezoelectric microactuator without loosing its piezoelectric deflection performance required for light modulating micromirror devices. The multi-layer piezoelectric actuator composed of PZT silicon nitride and platinum layers deflects or buckles due to the gradient of residual stress. Based on the structural analysis results and relationship between process conditions and mechanical properties we have modified the fabrication process and the thickness of thin film layers to reduce the initial residual stress deflection without decreasing its piezoelectric deflection performance. The modified designs fabricated by surface-micromachining process achieved the 77% reduction of the initial deflection compared with that of the conventional method based on the measured micromechanical material properties is applicable to the design refinement of multi-layer MEMS devices and micromechanical structures.

• Transactions on Electrical and Electronic Materials
• /
• 제18권3호
• /
• pp.144-147
• /
• 2017

In this study, two- and three-layer ceramic piezoelectric actuators were designed and simulated according to SUS316 thickness, actuator width, and mass using ATILA software in order to develop a piezoelectric actuator for haptic application. Numerical modelling based on the finite element method was performed to find the resonance frequencies and modal shapes of the actuator. The resonance frequency was affected by the thickness of the SUS316 plate and mass. On the other hand, the width of the actuator did not have a significant impact. Maximum displacements were generated at the center of a haptic three-layer ceramic piezoelectric actuator. The two-layer ceramic piezoelectric actuator with a mass of 2.6 g was suitable as $16.28{\mu}m$ at 265 Hz for haptic sensation application.

• Structural Engineering and Mechanics
• /
• 제23권2호
• /
• pp.163-175
• /
• 2006

In this paper, the dynamic response of a piezoelectric layer with a penny-shaped crack is investigated. The piezoelectric layer is subjected to an axisymmetrical action of both mechanical and electrical impacts. Two kinds of crack surface conditions, i.e., electrically impermeable and electrically permeable, are adopted. Based upon integral transform technique, the crack boundary value problem is reduced to a system of Fredholm integral equations in the Laplace transform domain. By making use of numerical Laplace inversion the time-dependent dynamic stress and electric displacement intensity factors are obtained, and the dynamic energy release rate is further derived. Numerical results are plotted to show the effects of both the piezoelectric layer thickness and the electrical impact loadings on the dynamic fracture behaviors of the crack tips.

• 소음진동
• /
• 제5권3호
• /
• pp.313-325
• /
• 1995

Two active/passive vibration dampers were designed to control a cantilever beam first mode of vibration. The active element was a piezoelectric polymer, polyvinlidene fluoride (PVDF). The passive damping was provided by the application of a viscoelastic layer on the surface of the steel beam. Two substantially different damper configurations were designed and tested. One damper consisted of a piezoelectric actuator bonded to one face of the beam, with a viscoelastic layer applied to the other surface of the beam. The second one was composed of a layer viscoeastic layer with one surface bonded to the beam, and with other being constrained by nine piezoelectric actuators connected in parallel. A control law based on the sign of the angular velocity of the cantilever beam was implemented to control the beam first mode of vibration. The piezoelectric sensor output was digitally differentiated to obtain the transverse linear velocity, and its sign was used in the control algorith. Two dampers provided the system a damping increase of a factor of four for the first damper and three for the second damper. Both dampers were found to work well at low levels of vibration, suggesting that they can be used effectively to prevent resonant vibrations in flexible structure from initiating and building up.

• 한국전기전자재료학회논문지
• /
• 제18권12호
• /
• pp.1124-1128
• /
• 2005

New piezoelectric actuator design, which can reduce the number of the stacking layer without lowering the piezoelectric displacement, is suggested in this work. Each layer of the new designed multilayer actuator has the same electrode pattern as the cross-sectioned layer of the existing multilayer actuator has. The piezoelectric displacement was calculated by Finite-Element Method (FEM) analysis. The maximum piezoelectric displacement of the new-designed actuator with 13 layers was calculated to be almost same value (55.9 ${\mu}m$) as that of the existing actuator with 25 layers(60.1 ${\mu}m$).

• Smart Structures and Systems
• /
• 제14권5호
• /
• pp.961-980
• /
• 2014

Based on the general theory of elasticity, the static behavior of 2-2 cement-based piezoelectric curved composites is investigated. The actuator consists of 2 cement layers and 1 piezoelectric layer. Considering the electrode layer between the cement layer and the piezoelectric layer as the elastic layer, the exact solutions of the mechanical and electrical fields of the curved composites are obtained by utilizing the Airy stress function method. Furthermore, the theoretical results are compared with the FEM results and good agreements (with almost no error) are obtained, thus proving the validity of this study. Furthermore, the influence of certain parameters is discussed, which can help to get the desired displacements and stresses. Finally, it is seen that the analytical model established in this paper works well, which could benefit the design of this kind of cement-based smart devices.