• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.235-235
• /
• 2013

We reported on the characteristics of organic solar cells (OSCs) fabricated on $HNO_3$-treated multilayer graphene (MLG) transparent electrodes. MLG electrodes were prepared using a chemical vapor deposition and a multi-transfer process. Compared to organic solar cells (OSCs) on the ITO electrodes had a fill factor of 65.97%, and a power conversion efficiency (PCE) of 3.364%, OSCs on the MLG (three-layer graphene) electrodes with sheet resistance of $274{\pm}1{\Omega}$/square and transparency of 92.1% had a fill factor of 43.46%, and a power conversion efficiency (PCE) of 2.019%. However, OSCs on the HNO3-treated MLG electrodes with lower sheet resistance of $119{\pm}1{\Omega}$/square had a fill factor of 57.54%, and a PCE of 2.861%. The results would provide a promising method to improve the performance of large-area OSCs based on MLG electrodes.

• Applied Science and Convergence Technology
• /
• v.23 no.5
• /
• pp.254-260
• /
• 2014

Organic solar cells have attracted extensive attention as a promising approach for cost-effective photovoltaic devices. However, organic solar cell has disadvantage of low power conversion efficiency in comparison with other type of solar cell, due to the recombination ratio of hole and electron is too large in the active layer. Thus we have change the surface structure of PEDOT:PSS layers to improve the current density by colloidal lithography method using various-size of polystyrene sphere. The two types of coating method were applied to fabricate the different pattern shape and height, such as spin coating and drop casting. Using the organic solvent, we easily eliminate the PS sphere and could make the varied pattern shapes by controlling the wet etching time. Also we have measured the electrical properties of patterned PEDOT:PSS film to check whether it is suitable for organic photovoltaics.

• Korean Journal of Materials Research
• /
• v.6 no.6
• /
• pp.568-575
• /
• 1996

The double sided buried contact(DSBC)silicon solar cell processing requires doping of the rear and front grooves with boron and phosphorus respectively. The successful electroless plating of these grooves with the appropriate metals haave been found to depend on the boron conditions for the rear fingers. However, an increased understanding of electroless plating has removed this restriction. Thus the DSBC cells using different boron conditions can be electrolessly plated with ease. This paper presents the recent work done on metallizing the double sided buried contact silicon solar cells with heavily doped boron grooves. The cells results indicate that, the heavier the boron grooves, the poorer the cell performance because of the probable higher metal contact recombination associated with boron grooves.

• Ceramist
• /
• v.21 no.1
• /
• pp.98-111
• /
• 2018

The lead-based perovskite (CH3NH3PbI3) material has a high molar coefficient, high crystallinity at low temperature, and long range of balanced electron-hole transport length. In addition, PCE of perovskite solar cells (PSCs) has been dramatically improved by over 22% by amending the electronic quality of perovskite and by using state-of-the-art hole transporting materials (HTMs) such as tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (spiro-OMeTAD) due to enhanced charge transport toward the electrode via properly aligned energy levels with respect to the perovskite. Replacing the spiro-OMeTAD with new HTMs with the desired properties of appropriate energy levels, high hole mobility in its pristine form, low cost, and easy processable materials is necessary for attaining highly efficient and stable PSCs, which are anticipated to be truly compatible for practical application. Furthermore, Recently Pb-free perovskite materials much attention as an alternative light-harvesting active layer material instead of lead based perovskite in photovoltaic cells. In this work, we demonstrate a Pb-free perovskite material for the light harvesting and emitter as optoelectronic devices.

• Ceramist
• /
• v.23 no.2
• /
• pp.145-165
• /
• 2020

Halide perovskites are promising photovoltaic materials due to their excellent optoelectronic properties like high absorption coefficient, low exciton binding energy and long diffusion length, and single-junction solar cells consisting of them have shown a high certified efficiency of 25.2%. Despite of high efficiency, perovskite photovoltaics show poor stability under actual operational condition, which is the mostly critical obstacle for commercialization. Given that the stability of the perovskite devices is significantly affected by charge-transporting layers, the use of inorganic charge-transporting layers with better intrinsic stability than the organic counterparts must be beneficial to the enhanced device reliability. In this review article, we summarized a number of studies on the inorganic charge-transporting layers of the perovskite solar cells, especially focusing on their effects on the enhanced device reliability.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.551-554
• /
• 2015

This paper was analyzed electrical characteristics of super junction IGBT with super junction field rings. As a result of super junction IGBT with super junction field rings, we obtained 3,300 V breakdown voltage and good thermal characteristics. we obtained shrinked chip size because field ring was decreased than field ring for conventional IGBT, too. And we fabricated super junction IGBT with super junction field rings. As a result of measuring fabricated chip, we obtained 3,300 V breakdown voltage. The fabricated devices were replaced thyristos using high voltage conversion, sufficiently.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.964-969
• /
• 2014

In Super Junction MOSFET, Charge Balance is the most important issue of the trench filling Super Junction fabrication process. In order to achieve the best electrical characteristics, the N type and P type drift regions must be fully depleted when the drain bias approaches the breakdown voltage, called Charge Balance Condition. In this paper, two methods from the fabrication process were used at the Charge Balance condition: Trench angle decreasing process and Bottom implantation process. A lower on-resistance could be achieved using a lower trench angle. And a higher breakdown voltage could be achieved using the bottom implantation process. The electrical characteristics of manufactured discrete device chips are compared with those of the devices which are designed of TCAD simulation.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.133-136
• /
• 2008

This paper presents a novel soft switching topology with resonant DC-DC converter and inverter. The resonant DC-DC converter consists of the auxiliary switch, resonant capacitor and inductor. All switches in the proposed topology is turn on at ZCS and turn off at ZVS operation. The proposed soft switching technology can be obtained the reduced switching losses and voltage and current stress of the power devices. Therefore, the resonant converter efficiency is higher than conventional boost converter. Simulation results on a 1kW soft switching converter are presented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.28-28
• /
• 2010

Photoelectrochemical solar cells such as dye-sensitized cells (DSSCs), which exhibit high performance and are cost-effective, provide an alternative to conventional p-n junction photovoltaic devices. However, the efficiency of such cells plateaus at 11-12%, in contrast to their theoretical value of 33%. Improvements in efficiency can only occur through a fundamental understanding of the underlying physics, materials, and device designs of DSSCs. A photoelectrode consisting of semiconducting oxide nanoparticles and a transparent conducting oxide electrode (TCO) is a key component of DSSC and design of photoelectrode materials is one of promising strategies to improving energy conversion efficiency. We introduce monodisperesed $TiO_2$ nanoparticles prepared by forced hydrolysis method and their superiority as photoelectrode materials was characterized with aids of optical and electrochemical analysis. Multi-layered TCO materials are also introduced and their feasibility for use as photoelectrodes is discussed in terms of optical absorption and charge collecting properties.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.584-587
• /
• 2006

An energy generating greenhouse based on fluoropolymer envelope and fresnel lens is proposed. The outstanding properties of the fluoropolymer films make them very suitable for large scale solar applications. Extremely high optical transmission over the whole solar spectrum, combined with mechanical strength, and durability allows us to design a highly optimized greenhouses for both plant growing and energy generation. Systems such as photovoltaic triple junction cells are especially attractive since they have up to 35% efficiency with much less cell material when the sun beam is focused with concentrators such as fresnel lenses. Cooling such devices will enhance the efficiency and provide useful thermal energy that could be further utilized for various applications depending on the local demands. This article introduces the basic ideas and principles of the energy generating greenhouses as a first step towards the actual deployment of such systems under Korean environment.