• Applied Chemistry for Engineering
• /
• v.20 no.6
• /
• pp.622-627
• /
• 2009

Using an alkali-solution developable photosensitive resin and a carbon black as a conductive filler, photo-patternable pastes for polymer thick film resistor were fabricated and evaluated. A photo solder resist (PSR), which is usually used as protecting layer of printed circuit board (PCB), was used as a photosensitive resin so that ultraviolet exposure and alkali-aqueous solution development of paste were possible. After fabricating the photosensitive polymer resistor paste, the electrical properties of thick film resistors were measured using PCB test boards. Sheet resistance was decreased with increasing amount of carbon black, but the developability was limited in excess loading of carbon black. The sheet resistance was also reduced by re-curing and the change rate was smaller in higher carbon black loading. Moreover, finely patterned meander-type thick film resistors were fabricated using photo-process and large resistance up to several tens of sheet resistance could be obtained in small area by this technique.

• Journal of Magnetics
• /
• v.12 no.2
• /
• pp.81-83
• /
• 2007

Etching of NiFe films covered with an organic photo-resist or Ti was successfully performed by an inductively coupled plasma-reactive ion etching (ICP-RIE) system using $CHF_3/O_2/NH_3$ discharges exchanging $CHF_3$ for $CH_4$ gas gradually. Experimental results showed that the organic photo-resist mask can be applied to the NiFe etching. In the case of the Ti metal mask, it was found that the etching-selectivity Ti against NiFe was significantly varied from 7.3 to ${\sim}0$ by changing $CHF_3/CH_4/O_2/NH_3$ to $CH_4/O_2/NH_3$ discharges used in the ICP-RIE system. These results show that the present RIE of NiFe was dominated by a chemical reaction rather than a physical sputtering.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.113-115
• /
• 1994

We considered the ion and photo-induced properties as a function of wavelength by exposing the light over the band gap of a-Ag/a-$Se_{75}$$Ge_{25}$ and the low-energy defocused $Ga^{+}$ ion beam on Ag/a-$Se_{75}$$Ge_{25}$ thin film. This film acts as a negative resist for photo or ion beam lithography. We observed that the absorbance coefficient decreased with increasing the photo-exposing time and exposing the ion beam. The bandgap shifts toward longer wavelength called a "darkening effect" are observed in the films exposed to both photons and ions. We suggest that a primary step in the Ag layer and a secondary step is in a-$Se_{75}$$Ge_{25}$ film layer.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.12
• /
• pp.128-135
• /
• 2007

Micro-channels for a wave micropump have been fabricated using the Stereolithography and UV Photolithography. The micro-channel with a channel height of $500\;{\mu}m$ was fabricated with stereolithography. UV photolithography was used for producing micro-channels with a channel length less than $100\;{\mu}m$. The fabrication process data including spinning rpm, pre-bake and post-bake time, and develop time for single layer and multiple layer 3D micro-structures using SU-8 photo resist are experimentally found. A film mask printed with a 40,000 dpi laser printer was used for UV lithography and micro-structures in the order of tens of micrometers in dimension were successfully fabricated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.60-63
• /
• 1999

Application of reactive ion etching (RIE) technique to Ta-Al alloy thin film with a thickness of $1000{\AA}$ was studied. $CF_{4}$ gas could be used effectively to etch the Ta-Al alloy thin film. The etching rate in the thin film with Ta content of 50 mol% was about $67{\AA}/min$. NO selectivity between the Ta-Al alloy film and $SiO_{2}$ film was observed during the etching using the $CF_{4}$ gas. The etching rate of the $SiO_{2}$ layer was 12 times faster than that of the Ta-Al alloy thin film. It was also observed that photoresist of AZ5214 was more useful than Shiepley 1400-27 in RIE with the $CF_{4}$ gas.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.116.1-116.1
• /
• 2016

반도체 가스센서에서는 가연성 및 탄화수소계 가스를 감지 하기 위해서 $100{\sim}500^{\circ}C$ 이상의 동작온도를 필요로 한며, 이에 따라 반도체식 가스센서의 마이크로 히터 소재는 고온에서 열적 안정성이 있는 소재가 요구된다. 현재 상용화되고 있는 반도체식 가스센서는 실리콘(Silicon) 기반의 MEMS 기술을 이용한 가스센서이며, 구조적으로나 성능적 한계가 드러남에 따라 실리콘 이외의 다양한 재료의 MEMS 응용기술 개발이 필요한 실정이다. 본 연구에서는 이러한 실리콘의 재료적 한계를 극복하기 위해 다공성 알루미늄 산화물(AAO)을 기판으로 사용하여 마이크로 히터를 제작하였다. AAO의 제작에 앞서 CMP, 화학연마, 전해연마를 이용하여 적합한 전처리 공정을 선정하였고, AAO 제작 시 온도, 시간, 전압의 변수를 주어 마이크로 히터 기판에 적합한 공정을 탐색하였다. 마이크로 플랫폼은 MEMS 공정으로 제작되었으며, PR(Photo Resist)을 LPR(Liquid Photo Resist)과 DFR(Dry Film Resist)로 각각 2종 씩 선택하여 AAO에 적합한 제품을 선정하였다. 제작된 마이크로 히터는 $1.8mm{\times}1,8mm$로 소형화 하였고, 열손실의 제어를 위해 열확산 방지층을 추가하였다. 구동 온도, 소비전력, 장시간 구동시 안정성의 측정 및 평가는 적외선 열화상 카메라와 kiethly 2420 source meter를 이용하여 측정하였으며, 열확산 방지층의 유 무에 따른 온도 분포 및 소비전력을 비교평가 하였다. 최종적으로는 현재 사용화 되어있는 가스센서들의 소비전력과 비교 평가 하여 논의 하였다.

• Applied Chemistry for Engineering
• /
• v.24 no.6
• /
• pp.593-598
• /
• 2013

In this study, we have evaluated the water absorption phenomenon of photoresist dry film, which is commonly used to build circuits on PCB (Printed Circuit Board) by photolithography, by using ATR-FTIR (Attenuated Total Reflectance-Fourier Transform Infrared). We have firstly observed significant change in fracture mode of dry film with respect to temperature and humidity, which we assumed the material transition from ductile to brittle. Secondly, we have established the process of absorption test for determining the diffusion coefficients of water into the dry film both with gravimeter and ATR-FTIR. We have successfully calculated the diffusion coefficients for each environmental conditions from the results which we achieved by gravimeter and ATR-FTIR. Compared to the gravimeter which is a conventional method for absorption test, the ATR-FTIR method in this study has been found to be very easy to use and have the same accuracy as gravimeter. Moreover, we are expecting to use the ATR-FTIR as an appropriate method to study the absorption phenomena related to any kinds of solvent and polymer system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.948-951
• /
• 2005

New technology that reduces photolithography process steps from 4 to 3 in fabrication of TFT LCD is introduced. The core technology for 3mask-TFTs is the lift-off process [1], by which the PAS and PXL layer are formed simultaneously. To evaluate the stability of this lift-off process, outgases from photo resist on a substrate during ITO deposition and the quality of ITO film were analyzed and the conventional photo resist stripper machine which operates lift-off process was examined to see its ability to reduce particle problems of the machine. Through the development of total process and design for TFTs using this 3mask technology, panels in TN and IPS modes which exhibit same performances of a display using a conventional process were achieved. In addition, this process was already verified in the mass production line and now some products are being produced by the 3mask technology.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.42.1-42.1
• /
• 2005

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1993-1998
• /
• 2011

Semiconductor industry needs to have fine patterns in order to fabricate the high density integrated circuit. For nano-scale patterns, hard-mask is used to multi-layer structure which is formed by CVD (chemical vaporized deposition) process. In this work, we prepared single-layer hard-mask by using organic-inorganic hybrid polymer for spin-on process. The inorganic part of hard-mask was much easier etching than photo resist layer. Beside, the organic part of hard-mask was much harder etching than substrate layer. We characterized the optical and morphological properties to the hard mask films using organic-inorganic hybrid polymer, and then etch rate of photo resist layer and hard-mask film were compared. The hybrid polymer prepared from organic and inorganic materials was found to be useful hard-mask film to form the nano-patterns.