• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.471-472
• /
• 2016

Since photovoltaic generating system is significantly important among renewable energy sources, photovoltaic plants are installed more than past. As a result, accidents of photovoltaic system are also increased, so the additional hardware which includes monitoring system and periodic inspection are required for safety. In addition, a photovoltaic system is installed where a person can't approach to detect a fault, so a number of devices are required to detect it. This paper proposes that drone and thermo-graphic camera are used for detecting a fault of photovoltaic plant and suggests efficiency to control a drone for detecting a photovoltaic plant.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.22-30
• /
• 2002

ln this paper, it was reported the developed results of the monitoring unit for 72.5kY GIS which it is one part of the monitoring system for the substation that Korea Railway Company is promoting. In order to monitor the operational status of GIS, four parameters were chosen: the number of times of the circuit breaker switching, tightness of the gas-sealed units (circuit breaker / disconnecting switch / earthing switch), the number of times of the lightning arrestor operating and the leakage current of the lighting arrester. We constructed the monitoring system that can be judged the operating condition of the GIS from the signal of the suitable sensor for the purpose. Therefore, it is possible to on line monitoring for the condition of the GlS without efforts of the Periodic inspection.

• Journal of Welding and Joining
• /
• v.18 no.3
• /
• pp.68-75
• /
• 2000

The incomplete penetration(IP) discontinuity in butt joint weld, which is detected during safety analysis of the steel bridge by nondestructive evaluation(NDE) method, is classified as unacceptable defect according to the NDE codes and standards. In fact, there are a little allowance in butt joint weld in the view point of design criterion, and also detected IP discontinuity should be classified and evaluated for the fatigue strength and residual life estimation. In this study, we performed fatigue test to evaluate the fatigue strength of high strength steel(SWS490A) containing IP discontinuities in various size, the results compared and classified according to the bridge construction standard specification which published by korea administration of construction and traffic. Experimental results could be used to evaluate and estimate the IP discontinuities considering different stress range in butt joint bridge weld during periodic safety inspection.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.201-203
• /
• 2001

Safety is emphasized in nuclear power plant system for its characteristic. One of the most important systems to guarantee the safety of nuclear power plant is the PPS(Power protection system). The measurement control system includes PPS, which is similar to the human nervous system, is very important factor not only for the safety but also for the operation. Therefore, developing a technology to level up the performance of measurement system and reliability of the plant will bring cost-effective and safe generation of nuclear power. In this study, I researched composition of digitized PPS and algorithm for cyclic inspection.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.219-223
• /
• 1995

Since the mid of 1970's, the construction of infrastructure has been booming and accelerating to keep up with rapid economic growth. Fast achievement of most construction activities has caused unfavorable effects of civil petitions associated with damages and nuisances due to last hasty works. it is well known that the falling down of Sungsoo bridge and the collapse of Sampoong department and other structures have occurred because of the construction not conforming with the specification, and thereby incurred enormous loss of life and property. Now a days. a periodic inspection and maintenance have been strongly interested on aged RC structures, of repair and reinforcement technique in the country, most repairing and reinforcing works have been performed on the basis of the guidance of few experienced local company in this field.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.676-682
• /
• 2007

In this paper we introduce the Failure Management System for AREX's Signalling System which is applied by RAMS management. The corrective action report is classified into 3 group, scheduled maintenance, non-scheduled maintenance and the reported failure maintenance. The scheduled maintenance is for the failure detected by periodic inspection and it is concerned as the Preventive Maintenance. The reported failure maintenance is for the failure reported by non-maintenance staff and non-scheduled maintenance includes all corrective action except the works of the previous 2 group. RAMS analysis is based on the FRACAS data connected with the corrective action reports. AREX computerize the all process by the Facility Management System of Integrated Information System.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.476-480
• /
• 2004

The characteristics of antimony implants are relatively well-known. Antimony has lower diffusion coefficient, shorter implantation range, and smaller scattering as compared with conventional dopants such as phosphorous and arsenic. It has been commonly used in the doping of buried layer in Bi-CMOS process. In this paper, characteristics and appropriate condition of monitoring in antimony implant beam tuning using Sb$_2$O$_3$were investigated to get a reliable process. TW(Thema Wave) and R$_{s}$(Sheet Resistance) test were carried out to set up condition of monitoring for stable operation through the periodic inspection of instruction condition. The monitoring was progressed at the point that the slant of R$_{s}$ varied significantly to Investigate the variation of instruction accurately.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.459-464
• /
• 2001

For major nuclear power plant components periodic inspections and integrity assessments are needed for the safety. But many flaws are undetectable due to sampling inspection. Probabilistic integrity assessment is applied to take into consideration of uncertainty and variance of input parameters arise due to material properties, applied load and undetectable flaws. This paper describes a Probabilistic Fracture Mechanics(PFM) analysis based on Monte Carlo(MC) algorithms. Taking important parameters as probabilistic variables such as fracture toughness, crack growth rate and flaw shape, failure probability of major nuclear power plant components is archived as a results of MC simulation. For the verification of these analysis, a comparison study of the PFM analysis using other commercial code, mathematical method is carried out and a good agreement was observed between those results.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.541-546
• /
• 2001

Application of bonding by adhesives can be found in many industries, particularly in advanced technological domains such as the aeronautical and space industries, automobile manufacture, and electronics. Periodic inspection with conventional ultrasonic NDE techniques is capable of indicating the presence and possible location of crack. Continuous ultrasonic attenuation monitoring has potential to supply information. This study used adhesive-bonded single-lap joints specimen to evaluate such possibility by ultrasonic signal processing method.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.312-313
• /
• 2018

As global climate change leaded to extensive natural disaster and radical deterioration of infrastructures, there was increased attentions for the evaluation of infrastructures. After the collapse of Seongsu Bridge in 1994, Korea has enacted the "Special act on safety and maintenance of facilities" and secured the safety of facilities using systematic and periodic safety inspections. However, current facility inspections are mainly performed by the physical defect and structural analysis, and do not properly consider the serviceability of infrastructure such as capacity of facility and user's satisfaction. Thus, the purpose of the study is to develop an evaluation criteria for serviceability of infrastructures and finally leading to the revision of "Special Act on safety and maintenance of facilities in rational manner.