• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.102-106
• /
• 2007

YBCO films have been synthesized using a spray pyrolysis method. We used nitrates of Y, Ba, Cu as precursors. Deposition was made on $LaAlO_3$ (100) single crystal substrate by spraying the mist of aqueous precursor solution generated by a concentric nozzle. The distance between concentric nozzle and substrate was 15 cm. C-axis oriented films were obtained at deposition temperature of $740{\sim}800^{\circ}C$ and working pressure of 20 Torr. Oxygen partial pressure was 3 Torr and substrate was transported with the speed ranging from 0.23 cm/min to 0.7 cm/min by reel to reel. Scanning electron microscope (SEM) and X-ray diffraction (XRD) observation revealed that films are smooth and highly textured with (001) planes parallel to substrate. Highest critical current density (Jc) was $1.38\;MA/cm^2$ at 77K and self-field for the film with a thickness of $0.5\;{\mu}m$ prepared at a substrate temperature of $780^{\circ}C$ and $PO_2\;=3\;Torr$. The effect of temperature on the microstructure and YBCO phase formation will be discussed.

• Journal of Welding and Joining
• /
• v.27 no.2
• /
• pp.69-75
• /
• 2009

The effects of welding speed were investigated on penetration characteristics, defects and mechanical properties including formability test in Nd:YAG laser welded 1000MPa grade DP steels. A shielding gas was not used and bead-on-plate welding was performed with various welding speeds at 3.5kW laser power. Defects of surface and inner beads were not observed in all welding speeds. As the welding speed increased, the weld cross-section varied from the trapezoid having wider bottom bead, through X type, finally to V type in partial penetration range of welding speeds. The characteristic of hardness distribution was also investigated. The center of HAZ had maximum hardness, followed by a slight decrease of hardness as approaching to FZ. Significant softening occurred at the HAZ near BM. Regardless of the welding speed, the weld showed approximately the same hardness distribution. In the perpendicular tensile test with respect to the weld direction, all specimens were fractured at the softening zone. In the parallel tensile test to the weld direction, the first crack occurred at weld center and then propagated into the weld. Good formability over 80% was taken for all welding conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.2
• /
• pp.323-329
• /
• 2002

This paper describes an efficient error-compensation technique for designing a low-error truncated Booth multiplier which produces an N-bit output from a two's complement multiplication of two N bit inputs by eliminating the N least-significant bits. Applying the proposed method, a truncated Booth multiplier for area-efficient and low-power applications has been designed, and its performance(truncation error, area) was analyzed. Since the truncated Booth multiplier does not have about half the partial product generators and adders, it results an area reduction of about 35％, compared with no-truncated parallel multipliers. Error analysis shows that the proposed approach reduces the average truncation error by approximately 60％, compared with conventional methods. A 16-b$\times$16-b truncated Booth multiplier core is designed on full-custom style using 0.35-${\mu}{\textrm}{m}$ CMOS technology. It has 3,000 transistors on an area of 330-${\mu}{\textrm}{m}$$\times$262-${\mu}{\textrm}{m}$ and 20-㎽ power dissipation at 3.3-V supply with 200-MHz operating frequency.

• Journal of Bio-Environment Control
• /
• v.1 no.1
• /
• pp.28-36
• /
• 1992

The wind pressure distributions were analyzed to provide fundamental criteria for the structural design on e single-span arched house according to the wind directions through the wind tunnel experiment. In order to investigate the wind force distributions, the variation of the wind force coefficients, the mean wind force coefficients, the drag force coefficients and the lift force coefficients were estimated by using the experimental data. The results obtained are as follows: 1. When the wind direction was normal to the wall, the maximum positive wind pressure along the height of the wall occurred approximately at two-thirds of the wall height because of the effects of boundary layer flow. 2. When the wind direction was 30$^{\circ}$ to the wall, the maximum positive wind force occurred at the windward edge of the wall. When the wind direction was parallel to the wall, the maximum negative wind force occurred at the windward edge of the wall. 3. The maximum negative wind force along the width of the roof appeared around the width ratio, 0.4, and that along the length of the roof appeared around the length ratio, 0.5. 4. According to the results of the mean wind force coefficients analysis, the maximum negative wind force occurred on the roof at the wind direction of 30$^{\circ}$. 5. The wind forces at the wind direction of 30$^{\circ}$ instead of 0$^{\circ}$ are recommended in the structural design of supports for a house. 6. To prevent partial damage of a house structure by wind forces, the local wind forces should be considered to the structural design of a house.

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.472-476
• /
• 2017

Porous W-10 wt% Ti alloys are prepared by freeze-drying a $WO_3-TiH_2$/camphene slurry, using a sintering process. X-ray diffraction analysis of the heat-treated powder in an argon atmosphere shows the $WO_3$ peak of the starting powder and reaction-phase peaks such as $WO_{2.9}$, $WO_2$, and $TiO_2$ peaks. In contrast, a powder mixture heated in a hydrogen atmosphere is composed of the W and TiW phases. The formation of reaction phases that are dependent on the atmosphere is explained by a thermodynamic consideration of the reduction behavior of $WO_3$ and the dehydrogenation reaction of $TiH_2$. To fabricate a porous W-Ti alloy, the camphene slurry is frozen at $-30^{\circ}C$, and pores are generated in the frozen specimens by the sublimation of camphene while drying in air. The green body is hydrogen-reduced and sintered at $1000^{\circ}C$ for 1 h. The sintered sample prepared by freeze-drying the camphene slurry shows large and aligned parallel pores in the camphene growth direction, and small pores in the internal walls of the large pores. The strut between large pores consists of very fine particles with partial necking between them.

• Proceedings of the Korea Society of Environmental Toocicology Conference
• /
• 2003.10a
• /
• pp.13-13
• /
• 2003

Methylmercury (MeHg) is a ubiquitous environmental toxicant that can be exposed to humans by ingestion of contaminated food including fish and bread. MeHg has been suggested to exert its toxicity through its high reactivity to thiols, generation of arachidonic acid and reactive oxygen species (ROS), and elevation of intracellular $Ca^{2+}$ levels (［$Ca^{2+}$］$_{i}$). However, the precise mechanism has not been fully defined. Here we show that phosphatidylcholine-specific phospholipase C (PC-PLC) is a critical pathway for MeHg-induced toxicity. MeHg activated the acidic form of sphingomyelinase (A-SMase) and group IV cytosolic phospholipase $A_2$ ($cPLA_2$) downstream of PC-PLC, but these enzymes as well as protein kinase C were not linked to MeHg's toxicity. Furthermore, MeHg produced ROS, which did not cause the toxicity. However, D6O9, an inhibitor of PC-PLC, significantly reversed the toxicity in a time- and dose-dependent manner in MDCK and SH-5YSY cells. Addition of EGTA to culture media resulted in partial decrease of [$Ca^{2+}$］$_{i}$ and partially blocked cell death. In contrast, D609 completely prevented cell death with parallel decreases in diacylglycerol and ［$Ca^{2+}$］$_{i}$. Together, our findings indicated that MeHg-induced toxicity was caused by elevation of ［$Ca^{2+}$]$_{i}$ through activation of PC-PLC. The toxicity was not attributable to the signaling pathways such as $cPLA_2$, A-SMase, and PKC, or to the generation of ROS.

• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.241-247
• /
• 2006

Structural studies have been performed on precipitation hardening discovered in $L1_2-ordered\;Ni_3(Al,Cr)$ containing 0.2 to 3.0 mol% of carbon using transmission electron microscopy (TEM). Fine octahedral precipitates of $M_{23}C_6$ appeared in the matrix by aging at temperatures around 973 K after solution treatment at 1423 K. TEM examination revealed that the $M_{23}C_6$ phase and the matrix lattices have a cube-cube orientation relationship and keep partial atomic matching at the {111} interface. After prolonged aging or by aging at higher temperatures, the $M_{23}C_6$ precipitates then adopt a rod-like morphology elongated parallel to the <100> directions. Deformation at temperature below 973 K, typical Orowan loops were observed surrounding the $M_{23}C_6$ particles. At higher deformation temperatures, the Orowan loops disappeared and the morphology of dislocations at the particle-matrix interfaces suggested the existence of attractive interaction between dislocations and particles. The change of the interaction modes between dislocation and particles with increasing deformation temperature can be considered as a result of strain relaxation at the interface between matrix and particles.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.30 no.3
• /
• pp.175-180
• /
• 2004

In this study, three treatment options to replace two posterior missing teeth were investigated using three dimensional finite element analysis: two wide(${\phi}5.0mm$) implants(the experimental model I), two standard(${\phi}3.75mm$) implants(the experimental model II), and three standard(${\phi}3.75mm$) implants(the experimental model III). Two kinds of load case were applied ; 1) perpendicular on occlusal surface(axial load), parallel on occlusal surface(lateral load). 2) perpendicular on occlusal surface(3mm lateral to central point). The results obtained from this study were as follows; value of Von-mises stress (equivalent stress) was smallest in the two wide implant among the three experimental models. It was reported that the diameter is the efficient factor than osseointegrated surface area.

• Journal of Adhesion and Interface
• /
• v.9 no.4
• /
• pp.30-33
• /
• 2008

Two polymeric interfaces with single component homo-polymers were prepared to control the orientation of block copolymer thin-film nanostructures. Poly(4-acetoxy styrene) (OH-PAS) and poly(4-methoxy styrene) (OH-PMS) which have the average chemical composition of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) were precisely synthesized through nitroxide-mediated radical polymerization. After dehydration reactions between above polymers and SiOx layers of silicon wafers, the polymer-modified interface induced partial (30%) vertical orientation of PS-b-PMMA thin film in the case of OH-PMS and wholly parallel orientation in the case of OH-PAS. Chemical compositions of polymeric interface layers are regarded as the key parameter to control the orientation of nanostructures of block copolymer thin film.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.9
• /
• pp.11-20
• /
• 1998

High-speed complex-number arithmetic units are essential to baseband signal processing of modern digital communication systems such as channel equalization, timing recovery, modulation and demodulation. In this paper, a new complex-number multiplication algorithm is proposed, which is based on redundant binary (RB) arithmetic combined with radix-4 Booth recoding scheme. The proposed algorithm reduces the number of partial product by one-half as compared with the conventional direct method using real-number multipliers and adders. It also leads to a highly parallel architecture and simplified circuit, resulting in high-speed operation and low power dissipation. To demonstrate the proposed algorithm, a prototype complex-number multiplier-accumulator (CMAC) core with 10-bit operands has been designed using 0.8-$\mu\textrm{m}$ N-Well CMOS technology. The designed CMAC core contains about 18,000 transistors on the area of about 1.60 ${\times}$ 1.93 $\textrm{mm}^2$. The functional and speed test results show that it can operate with 120-MHz clock at V$\sub$DD/=3.3-V, and its power consumption is given to about 63-mW.