• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.377-382
• /
• 2001

A suboptimal control law in turbulent pipe flow is derived and tested. Two sensing variables ${\partial}p/{\partial}{\theta}\;|_w\;and\;{\partial}{\upsilon}_{\theta}/{\partial}r\;|_w$ are applied with two actuations ${\phi}_{\theta}$ and ${\phi}_r$. To test the suboptimal control law, direct numerical simulations of turbulent pipe flow at $Re_r=150$ are performed. When the control law is applied, a $13{\sim}23%$ drag reduction is achieved. The most effective drag reduction is made at the pair of ${\partial}{\upsilon}_{\theta}/{\partial}r\;|_w$ and ${\theta}_r$. An impenetrable virtual wall concept is useful for analyzing the near-wall suction and blowing. The virtual wall concept is useful for analyzing the near-wall behavior of the controlled flow. Comparison of the present suboptimal control with that of turbulent channel flow reveals that the curvature effect is insignificant.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05a
• /
• pp.86-90
• /
• 2000

Partial discharge(PD) tests were performed when the hydrogenerator(rated 11kV and 25MVA) was shut down(off-line). Six cable couplers were installed in the ring bus as well as within hydrogenerator terminal box. PD tests were conducted using partial discharge analyzer(PDA) and digital partial discharge detector(PDD). PDA showed that the normalized quantity number(NQN) and the partial discharge magnitude increased with increase of ac voltage. Slot discharges were discovered in three phases(A, B and C) at the rated voltage. PDA and PDD test results are in accordance with the pattern and magnitude of partial discharge. This hydrogenerator stator windings were in good condition.

• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.239-242
• /
• 2008

In this paper, we developed HPF (high pass filter) consisted of lumped LC components to decrease the noises that are detected in PD (partial discharge) measuring test, and adapted it to field test. We tested under laboratory circumstances like the fields, and measured the phase change properties of detected signal in UHF sensor with Lemke probe and oscilloscope (TDS-3054, Tektronix).

• Journal of the Korean Data and Information Science Society
• /
• v.18 no.4
• /
• pp.1145-1155
• /
• 2007

In this paper, we consider the permutation tests for the multivariate data under the two-sample problem setting. We review some testing procedures, which are parametric and nonparametric and compare them with the permutation ones. Then we consider to try to apply the permutation tests to the multivariate data having the continuous and discrete components together by choosing some suitable combining function through the partial testing. Finally we discuss more aspects for the permutation tests as concluding remarks.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.5
• /
• pp.404-408
• /
• 2003

The characterization for several multi-layer embedded inductors with different structures was investigated. The optimized equivalent circuit models for several test structures were obtained from HSPICE. Building blocks are modeled using Partial element equivalent circuit method. The mean and the standard deviation of model parameters were extracted and predictive modeling was performed on different test structure. From this study, the characteristic of multi-layer inductors can be predicted.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.231-238
• /
• 2000

There was extreme improvement in the processing result of weld toe, but there is possibility that the fatigue failure occurs from the weld root part where the fatigue strength became low relatively. This study did the fatigue test at the cross rib specimens which implemented a partial penetration weld to improve the fatigue strength of the weld root part. As a result of the fatigue test of the partial penetration weld and the fillet weld specimens, almost the same fatigue strength appeared. Because the fatigue failure began from toe, there was not a reinforcement effect in the weld root part by the partial penetration weld. So, it examined fatigue strength at the partial penetration welding specimens which processed toe to stop the fatigue failure of toe part. As a result, there was big fatigue strength improvement from the partial penetration weld than the fillet weld. Therefore, if fatigue crack occurrence can be restrained from toe, it thinks that the fatigue strength of the root part can improve by the partial penetration weld, after all, it thinks that the overall fatigue life can improve.

• Journal of Energy Engineering
• /
• v.28 no.2
• /
• pp.47-54
• /
• 2019

As absorption type heat pump for waste heat recovery is installed in combined cycle power plant for Energy Service Company, performance test is implemented to confirm the operation data on partial load. The operation data changes according to the heat pump operation on partial load are as follows. Total heat output increases, because waste heat of closed cooling water and a portion of LP steam from HRSG is supplied. But electric power output of steam turbine is reduced, because LP steam to steam turbine is reduced. And heat output from HP district heater and LP district heater is reduced, because HP turbine exhaust steam to HP district heater and LP district heater is reduced. On partial load operation, turbine output reduction is higher than the base load operation. Therefore, on partial load, heat pump should be operated in consideration of the heat output increase and electric power output reduction.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1969-1971
• /
• 2004

For evaluation of partial discharge performances of electrical power appratus such as Insulator, circuit breaker and transformer and so on, Partial discharge measuring system(ERA) consisted of PD detector including amplifier, coupling capacitor, PD calibrator and voltage divider are used PD measuring system is very important factor which affect the test result and show reliability of test result in test laboratory, In this paper, we describe tracebility and uncertainty of PD measuring system in test laboratory based on IEC 60270.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.4
• /
• pp.30-37
• /
• 1998

In this paper, we propose a test generation method for large scale sequential circuits based on circuit partitioning to increase the size of circuits that the implicit product machine traversal (IPMT) method can handle. Our method paratitions a circuit under test into subset circuits with only single output, and performs a partial scan design using the state transtition cost that represents a degree of the connectivity of the subset circuit. The IPMT method is applied to the partitioned partial scan circuits in test generation. Experimental results for ISCAS89 benchmark circuits with more thatn 50 flip-flops show that our method has generated test patterns with almost 100% fault coverage at high speed by use of 34%-73% scanned flip-flops.

• Journal of Periodontal and Implant Science
• /
• v.32 no.3
• /
• pp.655-664
• /
• 2002

The purpose of this study was to observe the degree of surface obliteration of dentinal tubule using Gluma(R) desensitizer and MS coat(R) with 15 specimens made out of 15 extracted lower incisors. They were divided into Root planning group(control), Gluma(R) desensitizer group(test I ) and MS coat(R) group(test II). Degree of Obliteration was examined under the scanning electron microscope(${\times}$2000). The following results were obtained: 1. In the root planning group(control), the complete open of dentinal tubule surface was accounted for 73.8%, the partial obliteration for 17.2% and the complete obliteration for 9.0%. 2. In the Gluma(R) desensitizer group (test I), the complete open of dentinal tubule surface was accounted for 23.6%, the partial obliteration for 42.8% and the complete obliteration for 33.6%. 3. In the MS coat(R) group (test II), the complete open of dentinal tubule surface was accounted for 19.2%, the partial obliteration for 45.6% and the complete obliteration for 35.2%. 4. The average number of open dentinal tubules in the control was significantly higher than in the test I and II (P<0.05), but there were no statistically significant differences between the test I and II. 5. The average number of the partially obliterated and the completely blocked dentinal tubules in the control was significantly lower than the test I and II(P<0.05), but there were no statistically significant differences between the test I and II. The results of this study suggest that Gluma(R) desensitizer and MS coat(R) is significantly effective on dentinal tubule obliteration, therefore they were effective on hypersensitivity caused by periodontal treatment