• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2230-2234
• /
• 2003

This paper proposes a distributed simulator for general control system in CEMTool. Systems can be described by SIMTool likes the simulink in Matlab. For distributed simulation, we can seperate any system into several parallel subsystems in SIMTool. The number of parallel subsystem can be determined by the system's property. After seperation, parallel simulator will do initialization, one-step-ahead simulation, block-distribution and ordering and so on. Finally, simulator will create independent C codes and executive files for each subsystem. The whole system is fulfilled by several PCs, and each PC executes one subsystem. There are communications among these subsystem using reflective memory or ethernet. We have made several experiments, and the 5-stand cold rolling mill control system is our main target. The result of parallel simulation has shown effective speedup in comparison with one pc simulation.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.24-27
• /
• 2008

For high voltage DC-DC converters, the parallel operation of several high voltage source modules is necessary to reduce the material cost. In the conventional parallel operation with HDC module control unit, it is difficult to repair the HDC system for the failure of control unit. To overcome these problems, new parallel operating algorithm for high voltage DC-DC converter is presented. The proposed algorithm has no main control unit and each module can be selected as the master according to the operating conditions. Therefore, one of modules can be replaced as the master immediately when the previous master module is failed. In addition, the extension of extra modules can be simple.

• Journal of Communications and Networks
• /
• v.4 no.2
• /
• pp.118-127
• /
• 2002

This paper proposes a new scheme - parallel control scheme with feedback control (PCFC) for ABR services in ATM networks. The information from a source is split into a number of streams, for delivery over separate parallel connections with particular coding. At the receiver, the original information is reconstructed by the received packet from the parallel connections. The effects of PCFC on the network performance are due to two factors: Traffic splitting and load balancing. By combinations of analysis and simulation, this paper studies the implications of PCFC for how the ABR parameters should be scaled and the advantages of PCFC compared with other existing schemes.

• Journal of Power Electronics
• /
• v.5 no.4
• /
• pp.312-318
• /
• 2005

This paper presents a compensator for reduction of the reactive lateral current in multiple autonomously controlled uninterruptible power supplies (UPS) connected in parallel. This compensator acts directly on the control equation for voltage amplitude and it provides an improved current distribution especially in the case of parallel connection of UPSs with different output power ratings. Observations show that the original control equation for output voltage amplitude is efficient for voltage regulation but it causes great variation of voltage levels. A compensator with the same structure is added to counterbalance the variation caused by the original control equation. Simulations show promising results with the employment of the proposed compensator. Our simulations are confirmed by experimental results using three UPSs with different output ratings and voltage limiters ($1\%$) connected in parallel under various conditions.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.5
• /
• pp.1212-1220
• /
• 2013

In general, for a large power system like DC distribution system for buildings, several power converters are modularized for parallel operation. However, in parallel operation, inconsistency of parameters in each module causes circulating current in the whole system. Circulating current is directly related to loss, and, therefore, it is most important for the safety of the power system to supply the suitable current to each module. This paper proposes a control method to reduce circulating current caused during parallel operation. Accordingly, the validity of parallel operation system including response characteristics and normal state was verified by simulation and experiment result.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.59-67
• /
• 2003

This paper presents a new approach for the use of smart materials, piezoelectric materials of PVDF and PZT, for vibration attenuation of a planar parallel manipulator. Since lightweight linkages of parallel manipulators deform under high acceleration/deceleration, an active damper is needed to attenuate vibration due to structural flexibility of linkages. Based on the dynamic model of a planar parallel manipulator, an active damping controller is developed, which consists of a PD feedback control scheme, applied to linear electrical motors, and a linear velocity feedback (L-type) scheme applied to either PVDF layer or PZT actuator(5). Simulation results show that piezoelectric materials yield good damping performance, resulting in precise manipulations of a planar parallel manipulator.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.479-480
• /
• 2016

This paper introduces a master and slave control algorithm for parallel operation of UPS system. If each module of UPS system control the output voltage and filter inductor current in parallel operation, it occur unbalanced output power each module. To operate UPS system parallel, it need a algorithm that control output power of modules. A master and slave control algorithm is helpful to balance output power of modules by controlling output current. The effect of a master and slave control algorithm is proved by simulations.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.405-408
• /
• 1998

In this paper, a predictive current control of 12-pulse parallel connected dual converter system with interphase transfromer(IPT) is presented. Firstly, 12-pulse parallel connected dual converter system and the predictive current control of this system is discussed. And the validity of the presented system and the excellence of the predictive current control response is proved through the simyulation and experiment result.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.5
• /
• pp.482-489
• /
• 1997

This paper presents the analysis of the kinematics and dynamics of redundant parallel manipulators, and provides design guides for advanced parallel mainpulators with high performance. Three types of redundancies are considered which include the redundancies in serial chain, joint actuation, and parallelism. First, the kinematic and dynamic models of a redundant parallel manipulator are obtained in both joint and Cartesian spaces, and the kinematic and dynamic manipulabilities are defined for the performance evaluation. The effects of the three types of redundancies on the kinematic and dynamic performance of a parallel manipulator are then analyzed and compared, providing a set of guides for the design of advanced parallel manipulators. Finally, the simulation results using planer parallel manipulators are given.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.123-129
• /
• 2004

This paper concerns auto vergence control of a parallel stereoscopic camera through geometrical analysis. In the construction of a parallel stereoscopic camera, we experimentally demonstrated linear relationship between the key object distance and the amount of vergence control. And we proposed a vergence control system for the stereoscopic camera using binocular disparity information. For the real-time calculation of disparity information, the Hybrid Cepstral filter algorithm, with input data acquired from the vertical projection data and from the down sampling data from the source images, was proposed for precision and high speed processing. With the disparity information algorithm and the vergence control of the parallel stereoscopic camera system, the stereoscopic images become more like those of the human eye.