• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.5
• /
• pp.321-327
• /
• 2022

In this paper, a wrinkled structure was formed on the PDMS surface through UV/Ozone treatment, and the wrinkle structure formation mechanism was revealed through physicochemical characterization. A wrinkle structure was formed on the PDMS surface through UV/Ozone treatment for 30 min, and periodic wrinkle formation on the PDMS surface was confirmed by cross-sectional imaging of the scanning electron microscope. In addition, through x-ray photoelectron spectroscopy spectral analysis, it was confirmed that the silica-like-surface of SiOx on the PDMS surface was formed by UV/Ozone. The results of this study not only improve the understanding of the mechanism of wrinkle structure formation on the PDMS surface by UV/Ozone treatment, but also can be used as a basic study to adjust the amplitude and period of the wrinkle structure according to UV/Ozone irradiation conditions in the future.contact angles and the surface energies of FSAMs, it was confirmed that pretilt angles of LC molecules increased according to the alkyl chain length. High optical transparency and uniform homeotropic LC alignment characteristics of FSAMs showed the possibility of FSAMs as an LC alignment layers.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.39-46
• /
• 2019

A stiffness-gradient soft PDMS/hard PDMS/FPCB stretchable package of the island-bridge structure was processed using the polydimethylsiloxane (PDMS) as the base substrate and the more stiff flexible printed circuit board (FPCB) as the island substrate, and its effective elastic modulus and stretchable deformation characteristics were analyzed. With the elastic moduli of the soft PDMS, hard PDMS, and FPCB to be 0.28 MPa, 1.74 MPa, and 1.85 GPa, respectively, the effective elastic modulus of the soft PDMS/hard PDMS/FPCB package was analyzed as 0.58 MPa. When the soft PDMS of the soft PDMS/hard PDMS/FPCB package was stretched to a tensile strain of 0.3, the strains occurring at hard PDMS and FPCB were found to be 0.1 and 0.003, respectively.

• Journal of Sensor Science and Technology
• /
• v.30 no.3
• /
• pp.170-174
• /
• 2021

As the rising attention to the medical and healthcare issue, Bio-MEMS (Micro electro mechanical systems) platform such as bio sensor, cell culture system, and microfluidics device has been studied extensively. Bio-MEMS platform mostly has high resolution structure made by biocompatible material such as polydimethylsiloxane (PDMS). In addition, three dimension structure has been applied to the bio-MEMS. Lithography can be used to fabricate complex structure by multiple process, however, non-rectangular cross section can be implemented by introducing optical apparatus to lithography technic. X-ray lithography can be used even for sub-micron scale. Here in, we demonstrated lines with round shape cross section using the tilted gold absorber which was deposited on the oblique structure as the X-ray mask. This structure was used as a mold for PDMS. Molded PDMS was applied to the cell culture platform. Moreover, molded PDMS was bonded to flat PDMS to utilize to the sub-micro channel. This work has potential to the large area bio-MEMS.

• Journal of Sensor Science and Technology
• /
• v.33 no.3
• /
• pp.165-172
• /
• 2024

In this study, we investigated the detection properties of piezoresistive carbon nanotubes/polydimethylsiloxane (CNT/PDMS) devices with porous structures under applied pressure. The device, having dimensions of 10 mm × 10 mm × 5 mm, was fabricated with a porosity of 74.5%. To fabricate piezoresistive CNT/PDMS devices, CNTs were added using two different methods. In the first method, the CNTs were mixed with PDMS before the fabrication of the porous structure, while in the second, the CNTs were coated after the fabrication of the porous structure. Various detection properties of the fabricated devices were examined at different applied pressures. The CNT-coated device exhibited stable outputs with lesser variation than the CNT-mixed device. Moreover, the CNT-coated device exhibited improved reaction properties. The response time of the CNT-coated device was 1 min, which was approximately about 20 times faster than that of the CNT-mixed device. Considering these properties, CNT-coated devices are more suitable for sensing devices. To verify the CNT-coated device as a real sensor, it was applied to the gripping sensor system. A multichannel sensor system was used to measure the pressure distribution of the gripping sensor system. Under various gripping conditions, this system successfully measured the distributed pressures and exhibited stable dynamic responses.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.47-53
• /
• 2019

Stiffness-gradient stretchable electronic packages of the soft PDMS/hard PDMS/PTFE structure were processed using the polydimethylsiloxane (PDMS) as the base substrate and the more stiff polytetrafluoroethylene (PTFE) as the island substrate, and their stretchable deformation-resistance characteristics were characterized. The flip-chip joints, formed by bonding the chip bumps of 50 ㎛-diameter onto the PDMS/PTFE substrate pads, exhibited an average contact resistance of 96 mΩ. When the stretchable package of the soft PDMS/hard PDMS/PTFE structure was deformed to 30% elongation, the strain on the PTFE was restrained to 1%, resulting in a negligible resistance increase of 1% in the daisy-chain circuit formed on the PTFE island substrate. The circuit resistance increased for 1.7% after 2,500 cycles of 0~30% stretchable deformation.

• KSBB Journal
• /
• v.24 no.6
• /
• pp.515-520
• /
• 2009

This study presented facile method of cell patterning using fabricated PDMS patterns on polyelectrolyte coated surface. This basic principle is the fabrication of functional surface presenting two orthogonal surfaces such as cell adhesive and repellent properties. Cell adhesive surface was firstly fabricated with simple coating of polyelectrolyte multilayer. And then, the desired patterns of PDMS for the prevention of nonspecific binding of cells were transferred onto the previously formed thin film of polyelectrolyte multilayer. Thus, we could prepare novel functional surface simultaneously containing PDMS and polyelectrolyte region. As expected, the PDMS regions showed effective prevention of nonspecific binding of cell and the other region, exposed polyelectrolyte area, provided cell adhesive environment. The height of formed PDMS structure was about 100 nm. Based on this method, cell patterning can be successfully obtained with various pattern shapes and sizes. Therefore, we expect that this simple method will be useful platform technology for the development of cell chip, cell based assay system, and biochip.

• Journal of Adhesion and Interface
• /
• v.19 no.4
• /
• pp.154-162
• /
• 2018

Plasma treatment and corona treatment have been used for surface modification of polydimethylsiloxane (PDMS) film by activating its surface with the -OH group. Adhesion promoter or coupling agent was also used to improve adhesion of PDMS film with various materials. However, obtained hydrophilicity onto the surface of PDMS films with those processes was transient and vulnerable. In this study, a new alkoxysilane-functionalized acrylic polymer precursor was first synthesized by copolymerization process, and then was reacted with HO-terminated PDMS through condensation reaction to prepare a new surface modifier for PDMS film. The structure and molecular weight of the prepared surface modifier were confirmed by 1H-NMR and GPC measurement. Surface properties of surface modifier-coated PDMS films were also investigated by using XPS, ATR and WCA analysis. The adhesion between the PDMS film and the surface modifier was tested using cross-cut test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.3
• /
• pp.223-226
• /
• 2004

Injection molding using plastic materials was expected to mass production of structure with nano pattern for low cost phase. The PDMS mold was produced easily and uniformly by using thermal embossing. Quartz master for embossing method was made using electron beam lithography it had 100-500 nm size of line and dot type. The PDMS mold was produced after a brief hardening process and the master removal. The results show that various patterns are successfully fabricated the nano scale.. The replicated mold would be useful a stamper fabrication for injection molding.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.408-411
• /
• 2018

We fabricated highly flexible Mn-doped $SnO_2$ (MTO)/Ag/MTO/polydimethylsiloxane (PDMS)/MTO multilayer transparent conducting films. To reduce refractive-index mismatching of the MTO/Ag/MTO/polyethylene terephthalate (PET), index-matching layers were inserted between the oxide-metal-oxide-structured films and the PET substrate. The PDMS layer was deposited by spin-coating after adjusting the mixing ratio of PDMS and hexane. We investigated the effects of the index-matching layer on the color and reflectance differences with different PDMS dilution ratios. As the dilution ratio increased from 1:100 to 1:130, the color difference increased slightly, while the reflectance difference decreased from 0.62 to 0.32. The MTO/Ag/MTO/PDMS/MTO film showed a transmittance of 87.18~87.68% at 550 nm. The highest value of the Haacke figure of merit was $47.54{\times}10^{-3}{\Omega}^{-1}$ for the dilution ratio of 1:130.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.55-62
• /
• 2019

Stiffness-gradient stretchable electronic packages of the soft PDMS/hard PDMS/FPCB structure were processed using the polydimethylsiloxane (PDMS) as the base substrate and the more stiff flexible printed circuit board (FPCB) as the island substrate. The elastic characteristics of the stretchable packages were estimated and their long-term reliabilities on stretching cycles and bending cycles were characterized. With 0.28 MPa, 1.74 MPa, and 1.85 GPa as the elastic moduli of the soft PDMS, hard PDMS, and FPCB, respectively, the effective elastic modulus of the soft PDMS/hard PDMS/FPCB package was estimated as 0.6 MPa. The resistance of the stretchable packages varied for 2.8~4.3% with stretching cycles ranging at 0~0.3 strain up to 15,000 cycles and for 0.9~1.5% with 15,000 bending cycles at a bending radius of 25 mm.