• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.311-316
• /
• 2001

This paper presents that the affecting factors to the solderability and initial reliability. It is the factor that the coefficient of thermal expansion between package and PCB(Printed Circuit Board), the quantity of solder paste and reflow condition, and Au thickness of the solder ball pad on polyimide tape. As the reflow soldering condition for 48 ${\mu}BGA$ is changed, it is estimated that the quantity of Au diffusion at eutectic Sn-Pb solder surface and initial bonding strength of eutectic Sn-Pb solder and lead free solder. It is the result that quantitative measurement of Au diffusion quantity is difficult, but the shear strength of eutectic Sn-Pb solder joint is 842 mN at first reflow and increases 879 mN at third reflow. The major failure mode in solder is judged solder fracture. So, Au diffusion quantity is more affected by reflow temperature than by the reflow times.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.225-227
• /
• 2005

Sn-8wt%Zn-3wt%Bi (이하, Sn-8Zn-3Bi) 솔더의 장기 신뢰성을 평가하기 위하여 열 충격 시험을 행하였다. 열 충격 시험은 $-40^{\circ}C$에서 $80^{\circ}C$범위에서 1000 사이클 동안 하였다. 접합 기판으로는 각각 OSP(Organic Solderability Preservative), Sn 그리고 Ni/Au 처리를 한 PCB(Printed Circuit Board) 패드를 사용하였다. 접합에 사용한 부품은 1608 Chip(Multi Layer Chip Capacitor, Chip Resistor) 으로 전극 부위에 Sn-37wt%Pb, Sn 도금하여 사용하였다. 솔더링 후 1608 Chip의 전단 강도와 솔더링부에서 미세조직 및 IMC(Inter Metallic Compound) 변화를 관찰하였다. 측정결과, Sn-8Zn-3Bi 솔더의 초기 전단 강도는 기판의 표면처리에 상관없이 약 40N 이상이었다. 그리고 열충격 시험 1000 사이클 후에는 모든 기판에서 2N 정도 약간의 강도 저하를 보였다.

• 한국응용과학기술학회지
• /
• 제28권2호
• /
• pp.146-151
• /
• 2011

In this study, by using oleic acid and polypropylene glycol, good natured antifoaming agent for suitable electronics process under the alkaline conditions were synthesized. For the synthesized mono and diesters, acid value, hydroxyl value was measured, and identified by FT-IR and $^1H-NMR$ spectroscopy. Surface properties such as surface tension, critical micelle concentration(cmc) for diluted aqueous solution was measured, and tested the antifoaming properties according to the difference of alkyl chain length, various concentration, temperature and pH. The surface tension of synthesized antifoaming agent, PPMO(Polypropylene glycol monooleate) was 24.3 dyne/cm, PPDO(Polypropylene glycol dioleate) was 23.7 dyne/cm. By increasing of the alkyl chain length, surface tension was decreased slightly, and showed good antifoaming properties at 0.06 wt% concentration and $50^{\circ}C$, pH 11. These synthesized compounds are expected to apply as a suitable antifoaming agents in the semiconductor and the PCB(Printed Circuit Board) manufacturing process.

• ETRI Journal
• /
• 제35권4호
• /
• pp.625-631
• /
• 2013

For the formation of solder bumps with a fine pitch of 130 ${\mu}m$ on a printed circuit board substrate, low-volume solder on pad (LVSoP) technology using a maskless method is developed for SAC305 solder with a high melting temperature of $220^{\circ}C$. The solder bump maker (SBM) paste and its process are quantitatively optimized to obtain a uniform solder bump height, which is almost equal to the height of the solder resist. For an understanding of chemorheological phenomena of SBM paste, differential scanning calorimetry, viscosity measurement, and physical flowing of SBM paste are precisely characterized and observed during LVSoP processing. The average height of the solder bumps and their maximum and minimum values are 14.7 ${\mu}m$, 18.3 ${\mu}m$, and 12.0 ${\mu}m$, respectively. It is expected that maskless LVSoP technology can be effectively used for a fine-pitch interconnection of a Cu pillar in the semiconductor packaging field.

• 한국전자파학회지:전자파기술
• /
• 제24권2호
• /
• pp.15-22
• /
• 2013

Low-Temperature-cofired ceramics (LTCC) antenna packages have been extensively researched and utilized in recent years due to its excellent electrical properties and ease of implementing dense package integration topologies. This paper introduces some of the key research and development activities using LTCC packaging solutions for 60 GHz antennas at Samsung Electronics [1]. The LTCC 60 GHz antenna element topology is presented and its measured results are illustrated. However, despite its excellent performance, the high cost issues incurred with LTCC at millimeter wave (mmWave) frequencies for antenna packages remains one of the key impediments to mass market commercialization of mmWave antennas. To address this matter, for the first time to the author's best knowledge this paper alleviates the high cost of mmWave antenna packaging by devising a novel, broadband antenna package that is wholly based on low-cost, high volume FR4 Printed Circuit Board (PCB). The electrical properties of the FR4 substrate are first characterized to examine its feasibility at 60 GHz. Afterwards a compact multi-layer antenna package which exhibits more than 9 GHz measured bandwidth ($S_{11}{\leq}-10$ dB) from 57~66 GHz is devised. The measured normalized far-field radiation patterns and radiation efficiency are also presented and discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1587-1588
• /
• 2006

Tn this paper, PCB (Printed Circuit Board) embedded $BaTiO_3$ MIM capacitors were designed, fabricated, and characterized for low cost organic SOP applications by using 3-D EM simulator and low temperature processes. Size of electrodes and thickness of high dielectric films are optimized for improving the performance characteristics of the proposed embedded MIM capacitors at high frequency regime. The selected thicknesses of the $BaTiO_3$ film are $12{\mu}m$, $16{\mu}m$, and $20{\mu}m$. The fabricated MIM capacitor with dielectric constant of 30 and thickness of $12{\mu}m$ has capacitance density of $21.5p\;F/mm^2$ at 100MHz, maximum quality factor of 37.4 at 300 MHz, a quality factor of 30.9 at 1GHz, self resonant frequency of 5.4 GHz, respectively. The measured capacitances and quality factors are well matched with 3-D EM simulated ones. These embedded capacitors are promising for SOP based advanced electronic systems with various functionality, low cost, small size and volume.

• 조명전기설비학회논문지
• /
• 제29권2호
• /
• pp.1-7
• /
• 2015

The Light Emitting Diode(LED) lighting control system proposed in this thesis is made up of a sensor module, a microcontroller, Bluetooth wireless communication, LED Driver, and LED downlight. The sensor module, comprised of an infrared sensor, an illumination sensor, and a temperature sensor, was designed to one Printed Circuit board(PCB). The system is able to identify the environment information collected by the sensor, and make it possible to control lighting automatically and manually through sensors. In addition, depending on users' conditions, a color temperature can be controlled. CS-1000, a spectroradiometer, was employed to measure the changing values of a color temperature in 8 steps. According to a test, it was found that it was possible to change a color temperature from 3187K of Warm White LED to 5598K of Cool White LED. The Bluetooth based wireless communication technique makes it possible to control more lighting devices than other wireless communication techniques does.

• 대한기계학회논문집A
• /
• 제26권10호
• /
• pp.1997-2007
• /
• 2002

Composite air spindles are appropriate for the high-speed and the high-precision machining as small hole drilling of printed circuit board (PCB) or wafer cutting for manufacturing semiconductors because of the low rotational inertia, the high damping ratio and the high fundamental natural frequency of composite shaft. The axial load and stiffness of composite air spindles fur drilling operation are determined by the thrust ben ring composed of the air supply part mounted on the housing and the rotating part mounted on the rotating shaft. At high-speed rotation, the rotating part of the thrust bearing should be designed considering the stresses induced by centrifugal force as well as the axial stiffness and the natural frequency of the rotating shaft to void the shaft from failure due to the centrifugal force and resonant vibration. In this work, the air supply part of the thrust bearing was designed considering the bending stiffness of the bearing and the applied load. The rotating part of the thrust bearing was designed through finite element analysis considering the cutting forces during manufacturing as well as the static and dynamic characteristics under both the axial and con trifugal forces during high-speed rotation.

• ETRI Journal
• /
• 제41권5호
• /
• pp.670-683
• /
• 2019

In this paper, we analyzed the signal integrity of a system interconnection module for a proposed high-density server. The proposed server integrates several components into a chassis. Therefore, the proposed server can access multiple computing resources. To support the system interconnection, among the highly integrated computing resources, the interconnection module, which is based on Serial RapidIO, has been newly adopted and supports a bandwidth of 800 Gbps while routing 160 differential signal traces. The module was designed for two different stack-up types on a printed circuit board. Each module was designed into 12- (version 1) and 14-layer (version 2) versions with thicknesses of 1.5T and 1.8T, respectively. Version 1 has a structure with two consecutive high-speed signal-layers in the middle of two power planes, whereas Version 2 has a single high-speed signal placed only in the space between two power planes. To analyze the signal integrity of the module, we probed the S-parameters, eye-diagrams, and crosstalk voltages. The results show that the high-speed signal integrity of Version 2 has a better quality than Version 1, even if the signal trace length is increased.

• 한국신뢰성학회:학술대회논문집
• /
• 한국신뢰성학회 2005년도 학술발표대회 논문집
• /
• pp.339-348
• /
• 2005

In evaluation of electronic reliability on the PCB(Printed Circuit Board),electrochemical migration is one of main test objects. The phenomenon of electrochemical migration occurs In the environment of the high humidity and the high temperature under bias through a continuous aqueous electrolyte. In this paper, the generating mechanism of electrochemical migration is investigated by using water drop acceleration test under various waters. The waters used in the water drop test are city water, distilled water and ionic water. It found that the generated velocity o of electrochemical migration depended on the temperature of water and the electrolyte quantity which included in the various waters.