• 에너지공학
• /
• 제25권1호
• /
• pp.76-85
• /
• 2016

본 연구에서는 병참연료인 가솔린을 연료프로세서의 연료로 선택하여 광범위한 온도범위에서도 적용가능한 시동 및 제어 전략을 제시하였다. 가솔린 연료프로세서는 시동 초기 단계에서 연소 방식으로 상온상태의 자열개질기 촉매를 라이프온도까지 가열시킨다. 안정적인 가솔린-공기 혼합기체의 점화를 위하여 유동방향 기준 촉매 하단에 글로우 플러그를 설치하였다. 자열개질기가 촉매반응을 시작하면 가솔린 연료프로세서의 개질기는 정상상태까지 POX 모드, 부분 ATR 모드, 완전 ATR 모드 순으로 운전된다. 최종적으로 확립된 시동 및 제어 전략은 상온 및 저온 환경에서 가솔린 연료프로세서의 실제 실험을 통해 타당성을 확인하였다. 그 결과 가솔린 연료프로세서는 상온 및 저온에서 40분 이내에 정상상태에 도달하여 수소 37 ~ 42 vol.%(dry basis), 일산화탄소 0.3 vol.%의 개질가스를 생성할 수 있었다.

• 한국재료학회지
• /
• 제22권4호
• /
• pp.202-206
• /
• 2012

$CoSi_2$ was formed through annealing of atomic layer deposition Co thin films. Co ALD was carried out using bis(N,N'-diisopropylacetamidinato) cobalt ($Co(iPr-AMD)_2$) as a precursor and $NH_3$ as a reactant; this reaction produced a highly conformal Co film with low resistivity ($50\;{\mu}{\Omega}cm$). To prevent oxygen contamination, $ex-situ$ sputtered Ti and $in-situ$ ALD Ru were used as capping layers, and the silicide formation prepared by rapid thermal annealing (RTA) was used for comparison. Ru ALD was carried out with (Dimethylcyclopendienyl)(Ethylcyclopentadienyl) Ruthenium ((DMPD)(EtCp)Ru) and $O_2$ as a precursor and reactant, respectively; the resulting material has good conformality of as much as 90% in structure of high aspect ratio. X-ray diffraction showed that $CoSi_2$ was in a poly-crystalline state and formed at over $800^{\circ}C$ of annealing temperature for both cases. To investigate the as-deposited and annealed sample with each capping layer, high resolution scanning transmission electron microscopy (STEM) was employed with electron energy loss spectroscopy (EELS). After annealing, in the case of the Ti capping layer, $CoSi_2$ about 40 nm thick was formed while the $SiO_x$ interlayer, which is the native oxide, became thinner due to oxygen scavenging property of Ti. Although Si diffusion toward the outside occurred in the Ru capping layer case, and the Ru layer was not as good as the sputtered Ti layer, in terms of the lack of scavenging oxygen, the Ru layer prepared by the ALD process, with high conformality, acted as a capping layer, resulting in the prevention of oxidation and the formation of $CoSi_2$.

• Asian-Australasian Journal of Animal Sciences
• /
• 제27권11호
• /
• pp.1623-1629
• /
• 2014

Dry-cured pork neck samples were stored at $10^{\circ}C$ for 90 days under vacuum packaging (VP) or modified atmosphere packaging (MAP; 25% $CO_2$+75% $N_2$) conditions. The pH, moisture, water activity, total aerobic bacteria, and Enterobacteriaceae counts of dry-cured pork neck products with MAP were significantly lower than those with VP (p<0.05) after 90 days of storage. However, CIE $b^*$ and 2-thiobarbituric acid reacted substance (TBARS) values of the pork product with MAP were significantly higher (p<0.05) than those with VP. Total aerobic bacterial counts and Enterobacteriaceae counts of samples with MAP were lower than those with VP after 30 days of storage. Sensory results indicated that aroma, flavor and tenderness scores of the samples with both VP and MAP decreased during storage and the scores after >60 days of storage were lower than those at Day 1. In conclusion, despite presenting higher lipid oxidation, the samples stored in packages containing 25% $CO_2$ for 90 days at $10^{\circ}C$ have lower bacterial counts than vacuum-packed samples. Therefore, further studies should be performed on the packaging of dry-cured meat at adjusted concentrations of $CO_2$.

• ETRI Journal
• /
• 제35권3호
• /
• pp.425-430
• /
• 2013

In this paper, we propose a triple-gate trench power MOSFET (TGRMOS) that is made through a modified RESURF stepped oxide (RSO) process, that is, the nitride_RSO process. The electrical characteristics of TGRMOSs, such as the blocking voltage ($BV_{DS}$) and on-state current ($I_{D,MAX}$), are strongly dependent on the gate configuration and its bias condition. In the nitride_RSO process, the thick single insulation layer ($SiO_2$) of a conventional RSO power MOSFET is changed to a multilayered insulator ($SiO_2/SiN_x/TEOS$). The inserted $SiN_x$ layer can create the selective etching of the TEOS layer between the gate oxide and poly-Si layers. After additional oxidation and the poly-Si filling processes, the gates are automatically separated into three parts. Moreover, to confirm the variation in the electrical properties of TGRMOSs, such as $BV_{DS}$ and $I_{D,MAX}$, simulation studies are performed on the function of the gate configurations and their bias conditions. $BV_{DS}$ and $I_{D,MAX}$ are controlled from 87 V to 152 V and from 0.14 mA to 0.24 mA at a 15-V gate voltage. This $I_{D,MAX}$ variation indicates the specific on-resistance modulation.

• Bulletin of the Korean Chemical Society
• /
• 제25권4호
• /
• pp.511-516
• /
• 2004

A Li$[Co_{0.17}Li_{0.28}Mn_{0.55}]O_2$ cathode compound was prepared by a simple combustion method. The X-ray diffraction pattern showed that this compound could be classified as ${\alpha} -NaFeO_2$ structure type with the lattice constants of a = 2.8405(9) ${\AA}$ and c = 14.228(4) ${\AA}$. According to XANES analysis, the oxidation state of Mn and Co ions in the compound were 4+ and 3+, respectively. During the first charge process, the irreversible voltage plateau at around 4.65 V was observed. The similar voltage-plateau was observed in the initial charge profile of other solid solution series between $Li_2MnO_3\;and\;LiMnO_2$ (M=Ni, Cr...). The first discharge capacity was 187 mAh/g and the second discharge capacity increased to 204 mAh/g. As the increase of cycling number, one smooth discharge profile was converted to two distinct sub-plateaus and the discharge capacity was slowly decreased. From the Co and Mn K-edge XANES spectra measured at different cyclic process, it can be concluded that irreversible transformation of phase is occurred during continuous cycling process.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.308-309
• /
• 2016

Reducing surface recombination is a critical factor for high efficiency silicon solar cells. The passivation process is for reducing dangling bonds which are carrier. Tunnel oxide layer is one of main issues to achieve a good passivation between silicon wafer and emitter layer. Many research use wet-chemical oxidation or thermally grown which the highest conversion efficiencies have been reported so far. In this study, we deposit ultra-thin tunnel oxide layer by PECVD (Plasma Enhanced Chemical Vapor Deposition) using $N_2O$ plasma. Both side deposit tunnel oxide layer in different RF-power and phosphorus doped a-Si:H layer. After deposit, samples are annealed at $850^{\circ}C$ for 1 hour in $N_2$ gas atmosphere. After annealing, samples are measured lifetime and implied Voc (iVoc) by QSSPC (Quasi-Steady-State Photo Conductance). After measure, samples are annealed at $400^{\circ}C$ for 30 minute in $Ar/H_2$ gas atmosphere and then measure again lifetime and implied VOC. The lifetime is increase after all process also implied VOC. The highest results are lifetime $762{\mu}s$, implied Voc 733 mV at RF-power 200 W. The results of C-V measurement shows that Dit is increase when RF-power increase. Using this optimized tunnel oxide layer is attributed to increase iVoc. As a consequence, the cell efficiency is increased such as tunnel mechanism based solar cell application.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.157.1-157.1
• /
• 2016

In this work, we experimentally investigated the solar absorption performance of Cu-based scalable nanostructured surfaces and compared their performance with the conventional TiNOX. We fabricated Cu-based nanostructured surfaces with a controlled chemical oxidation process applicable to a large area or complex geometry. We optimized the process parameters including the chemical compounds, dipping time and process temperature. We conducted both lab-scale and outdoor experiments to characterize the conversion efficiency of each absorber surfaces with single and double glazing setup. Lab-scale experiment was conducted with $50mm{\times}50mm$ absorber sample with 1-sun condition (1kW/m2) using a solar simulator (PEC-L01) with measuring the temperature at the absorber plate, cover glass, air gap and ambient. From the lab-scale experiment, we obtained ${\sim}91^{\circ}C$ and $94^{\circ}C$ for CuO and TiNOX surfaces after 1 hr of solar illumination at single glazing, respectively. To measure the absorber performance at actual operating condition, outdoor experiment was also conducted using $110mm{\times}110mm$ absorber sample. We measured the solar flux with thermopile detector (919P-040-50). From outdoor experiment, we observed ${\sim}123^{\circ}C$ and $131^{\circ}C$ for CuO and TiNOX with 0.6 kW/m2 insolation at double glazing, respectively. We showed that the suggested nanostructured CuO solar absorber has near-equivalent collection efficiency compared with the state-of-the-art TiNOX surfaces even with much simpler manufacturing process that does not require an expensive equipment.

• 대한기계학회논문집B
• /
• 제28권3호
• /
• pp.265-270
• /
• 2004

Experiment study on a down scaled two-phase catalytic reactor is presented. As a preliminary step for the development of catalytic reactor, nano-particulate catalyst was prepared. Perovskite La$\_$0.8/Sr$\_$0.2/CoO$_3$is chosen and synthesized as a catalyst considering superior catalytic performance in reduction and oxidation process where oxygen is involved among the reagent. Reactor that has a scale of 2${\times}$10${\times}$25mm was made by machining of A1 block as a layered structure considering further extension to micro-machining. Hydrogen peroxide of 70wt% was adopted as reactant and was provided to the reactor loaded with 1.5 g of catalyst. Reactant flow rate was varied by precision pump with a range of 0.15cc/min to 17.2cc/min. Temperature distribution within reactor was recorded by 3 thermocouples and total amount of liquid product was measured. Temperature distribution and factors that affect temperature were observed and relation between temperature distribution and production rate was also analyzed. Relative time scale plays a significant role in the performance of the reactor. To obtain steady state operation, appropriate ratio of flow rate, catalyst mass and reactor geometry is required and furthermore to get more efficient production rate temperature distribution should be evenly distributed. The database obtained by the experiment will be used as a design parameter for micro reactor.

• Elastomers and Composites
• /
• 제43권4호
• /
• pp.259-263
• /
• 2008

저밀도 폴리에틸렌에 대한 장시간 저온 열처리가 저밀도 폴리에틸렌 고분자의 결정화도에 미치는 효과를 고체 수소 핵자기공명을 이용하여 연구하였다. 장시간 열처리는 첫째, 저밀도 폴리에틸렌의 색깔을 엷은 노란색으로 변하게 하였고 둘째, 저밀도폴리에틸렌에서 수소 핵의 스핀-스핀 및 스핀-격자 완화시간을 증가시켰으며, 셋째, 결정화도를 줄어들게 하였다. 먼저, $T_1$의 증가를 저밀도폴리에틸렌의 전체 스핀-격자 완화시간을 결정하는 비정질 영역의 부피 감소에 의한 것이거나 분자간 가교나 수소결합에 의한 특정 분자 운동 성분의 느려짐에 의해 발생하는 것으로 고려하였다. 하지만 결정화도의 감소는 열처리에 의한 비정질 영역의 감소를 의미하므로 전자와는 배치되었다. 따라서 $T_1$의 증가는 후자에 의한 결과임을 알 수 있었다.

• 한국약용작물학회지
• /
• 제17권4호
• /
• pp.233-237
• /
• 2009

Astragalus membranaceus has a long history of medicinal use in Chinese herbal medicine. It has been shown to have immunostimulant, tonic, antioxidant, antiperspirant, diuretic, anti-diabetic, expectorant properties, and a supplementary medicine during cancer therapy. In this study, we investigated the effect of anti-oxidation of Astragalus membranaceus root extract. The anti-oxidative activities of water, 80% methanol, and 100% methanol extracts from Astragalus membranaceus were analyzed by DPPH free radical scavenging activity, Superoxide dismutase-like activity, reducing power, and crude ash. The water extract demonstrated to be more effective than methanol extract for a DPPH radicals scavenging activities and reducing power. Superoxide dismutase-like activity showed higher efficiency in 80% methanol extract. Our results indicate that Astragalus membranaceus extracts could be used as a source of antioxidant ingredients in the food industry.