• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.32-44
• /
• 2002

This paper contains the information that describes the test fixture design and technology for full-scale airframe static test. Obtained technologies consist of determination of design load for test fixture, design technique for loading system, counterbalance system, positioning system of test article, test equipment and overload protection method. Full-scale airframe static test of advanced jet trainer was implemented using test fixture which are applied these technique.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.897-902
• /
• 2011

This study incorporates a welder and a generator as needed while using the generator to be used as a welder is to configure the system. As such, in order to offer an integrated system to prevent the rapid charging process to manage the power state information, system configuration is the most important. Ideally, the random controls the flow of charge is ideal for that. When charging is good as long as possible, less current. However, In this study, the most ideal fusion welder and generator as required by the generator or welder can be used as a system is proposed. Specifically, the damage can be caused by carelessness, so short-circuit protection, overload protection, reverse polarity protection, automatic charging system is all about, including the ability to adjust.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.7
• /
• pp.877-882
• /
• 2014

The reduction of CO2 emission has been discussed in the Marine Environment Protection committee in the International Maritime Organization as the biggest causes of GHG for the purpose of indexing CO2 amounts released into the atmosphere from ships. Accordingly, various methods including the change in the hull design to improve energy efficiency, the coating development to reduce friction resistances, the additives development for improving thermal efficiency in an engine, the low-speed operation to reduce fuel consumptions, and etc. have been applied. The main engine of a ship is an electronic engine for improving the efficiency of the whole load area. However, marine generator engines still use mechanical drive engines in intake, exhaust, and fuel injection valve drive cams. In addition, most of marine generator engines in ships apply a part-load operation of less then 80% due to an overload protection system. Therefore, marine auxiliary diesel engine set at 100% load is necessary to readjust in order to efficient operation because of part-load operation. The objective of this study is to report the results of the part-load fuel consumption improvement by injection timing readjust to identifying the operational characteristics of a marine generator engine currently operated in a ship.

• Fire Science and Engineering
• /
• v.33 no.5
• /
• pp.130-139
• /
• 2019

This study identified the level of task stress experienced by fire protection system management workers and analyzed the effects of task stress on job satisfaction and proposed future response. First, task stress according to background cause showed differences in relation to age, position, monthly salary, total career, license, and task, but there was no difference in relation to academic background. Second, of the sub-parameters of stress, physical environment, task demand, organizational system, lack of reward, and workplace culture have negative effects on job satisfaction as stress increases, while interpersonal relation conflict and job insecurity do not have any effect. In the future, it will be necessary to investigate the empirical causes of work overload and to study organization-level stress relief measures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.127-129
• /
• 2005

We investigated the fault current limiting characteristics according to the various facilities in power system. Power systems are becoming larger and larger for meeting electric power demand. Therefore, the over-currents resulting from contingencies such as short circuits are increasing higher, which causes the ratings of circuit breakers(CBs) to increase. Upgrading or replacement of CBs is not difficult from the technical and economical point of view. Bus split is being adopted into a part of 154 kV power systems, but it has adverse effects such as overload to neighboring power systems, increased voltage fluctuation, and decreased power system stability. For 345 kV power systems, the bus split measure is not feasible and dc reactors are being suggested. The superconducting fault current limiter is a protection gear of new concept that limits fault current automatically in a few milliseconds. It can also provide the effect of CB capacity increase, relaxation of power machine criteria, enhancement in power system reliability, and flexible power system operation.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.2
• /
• pp.1-7
• /
• 2015

In this paper, a new capacitive pressure sensor has been proposed for a displacement measurement. The new sensor is mainly composed of a gap of $5{\mu}m$ and a notch of $1{\mu}m$. And the sensor has the performance as the high sensitivity and capacitance compared with a commercial capacitive sensor. Therefore, the advantages of the new capacitive pressure sensor are good sensitivity in normal range, mechanically robust and large overload protection. The analytical model is induced for confirming the performance of the proposed sensor. In addition, FEM (finite elements method) simulation has been performed to verify the analytical model. Firstly, the displacement characteristics of diaphragm membrane were simulated by the analytical model and FEM in the case of different structure and materials. At last, through this analysis, these simulation results can be predicted the change of the performance when the device parameters are varied. And it is used as a design tool to achieve at a set of performance we desired.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.476-478
• /
• 2001

Coordination under short-circuit conditions is a systematic application of protective devices in the electrical power system, which, in response to a fault, will remove only a minimum amount of equipment from service. The objective is not only to minimize the equipment damage and process outage costs, but also to protect personnel from the effects of these failures. The coordination study of an electric power system consists of an organizes time-current study of all devices in series from the utilization device to the source. This study is a comparison of the time it takes the individual devices to operate when certain levels of normal or abnormal current pass through the protective devices. The objective of a coordination study is to determine the characteristics, ratings, and settings of overcurrent protective devices that will ensure that the minimum unfaulted load is interrupted when the protective devices isolate a fault or overload anywhere in the system. At the same time, the devices and settings selected should provide satisfactory protection against overloads on the equipment and interrupt short-circuit as rapidly as possible.

• Journal of the Korean Society of Safety
• /
• v.28 no.2
• /
• pp.21-25
• /
• 2013

The purpose of this study is to provide basic data for the safety assessment of a water purifier when water leaks due to inappropriate maintenance and the examination of the cause of accidents related to the leak. Due to its inspection and management by non-specialists, if a leak occurs in a water purifier with the water level controller being inclined, it may result in the failure of the compressor, power supply line, PCB, etc. The analysis of the thermal diffusion pattern of water purifier compressors using a thermal image camera shows that its maximum temperature was approximately $80^{\circ}C$. In addition, its operating current was a maximum of 13 A and the system's operating current was approximately 1.7 A after the compressor was charged. It was found that the housing type power cable cover of the compressor had the effect of preventing electric shock but has poor flame resistance. Furthermore, the performance of the overload protector, PTC relays, etc., was excellent but they have potential for problems as metallic terminals were exposed, resulting in the potential of a safety related accident. The terminals and their surface damaged by the tracking showed a trace of carbonization and the resistance between terminals was measured to be approximately $8{\Omega}$. In addition, while the tracking was proceeding, the fuse and circuit breaker installed for system protection did not operate.

• Journal of Drive and Control
• /
• v.20 no.1
• /
• pp.8-15
• /
• 2023

With the recent trend of intelligence and automation of construction work, a double-blade road cutter is being developed that automatically enables cutting along the cutting line marked on the road using a vision system. The road cutter can recognize the cutting line through the camera and correct the driving route in real-time, and it detects the load of the cutting blade in real-time to control the driving speed in case of overload to protect workers and cutting blades. In this study, a vision system mounted on a double-blade road cutter was developed. A cutting route recognition technology was developed to stably recognize cutting lines displayed on non-uniform road surfaces, and performance was verified in similar environments. In addition, a vision sensor protection module was developed to prevent foreign substances (dust, water, etc.) generated during cutting from being attached to the camera.

• Journal of Digital Contents Society
• /
• v.8 no.4
• /
• pp.483-489
• /
• 2007

The high availability of information security system shall be primarily studied in relation to the Next Generation Network(NGN) Information Security infrastructure, because it is very important to maintain availability at each moment as a variety of intrusions occur continuously. The high availability of the security system can be realized with the topology and configuration properly defined to fully utilize the recovery function of the security system in the thoroughly planned optimized method. The active-active high availability on the NGN information security infrastructure system in is assured by letting the failover mechanism operate upon the entire structure through the structural design and the implementation of functions. The proposed method reduces the system overload rating due to trouble packets and improves the status of connection by SNMP polling trap and the ICMP transport factor by ping packet.