• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.99-104
• /
• 2005

The CARB in USA has demanded OBD functions that detect any deterioration of performance of OTS as well as a simple defect of OTS which can affect emission to meet the reinforced emission regulation. In this paper, OTS plausibility monitoring functions to meet the demand from CARB are discussed. The output from OTS is used for the diagnostics of the torque converter clutch stuck and the gear ratio synchronous error. It is possible to diagnose the abnormality of OTS function by considering the oil temperature characteristics which changes according to the driving status of vehicles. In result, the OBD regulations of the CARB can be satisfied obligating car manufacturer to detect any problems in OTS functions which can affect emissions.

• 대한전기학회논문지
• /
• 제39권1호
• /
• pp.49-56
• /
• 1990

An induction motor position control system based on the sliding mode control is presented. In the sliding mode control, control function is discontinuous on the hyperplane, which causes harmful effects such a s current harmonics and acoustic noise in the motor drive application. In this study, a low pass filter is introduced between the sliding mode controller output and the motor controller input to reduce these effects. The filter, however, makes the torque response slggish and the system performance may become poor in cost of chattering reduction. To overcome these problems, the bandwidth of the filer is varied according to the error function. It is shown that the proposed sliding mode control with variable-bandwidth filter shows good performance, which is confirmed through experiments.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.362-371
• /
• 2018

This work proposes FPGA implementation of Carrier Disposition PWM for closed loop seven level diode clamped multilevel inverter in speed control of induction motor. VLSI architecture for carrier Disposition have been introduced through which PWM signals are fed to the neutral point seven level diode clamped multilevel using which the speed of the induction motor is controlled. This proposed VLSI architecture makes the power circuit to work better with reduced stresses across the switches and a very low voltage and current total harmonic distortion (THD). The output voltages, currents, torque & speed characteristics for seven level neutral point diode clamped multilevel inverter for AC drive was studied. It has observed the proposed scheme introduces less distortion and harmonics. The results were validated using real time results.

• 전기의세계
• /
• 제16권1호
• /
• pp.1-2
• /
• 1967

The development of the frequency converter using semiconductor enables to easily control the speed of alternating current machineries. In such case, it is desired to observe how several characteristics are changed, such as primary current, power factor, torque, secondary output, efficiency and transient performance. In this paper, the above characteristics are investigated by means of computational method from various constants relating to the motor which is designed in rated frequency 60 cycles. Transient fluctuations in motor speed are also observed with graphical method. These have been validated by the experimental results. When the frequency is to be varied in order to control the speed, it is seen that some of characteristics are getting better and others worse contrarily. The above characteristics may be applied to the optimum electrical, mechanical design of the motor which puts emphases on speed control.

• 대한전기학회논문지
• /
• 제38권11호
• /
• pp.888-895
• /
• 1989

A novel model reference adaptive control (MRAC) scheme for electrical servo drives is proposed, in which the control input is synthesized without any parameter identification mechanism and a PI controller is inserted ahead of the plant to reduce the steady state chattering. The proposed scheme is shown to be asymptotically stable in the case where the load torque disturbance satisfies a certan condition. An application to a permanent magnet synchronous motor drive shows that the output error between the plant and the reference model tends to zero and the chattering is greatly reduced.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1007-1009
• /
• 2004

This paper describes the design and the performance analysis of high speed induction motor considering end-ring using F.E.M.. To investigate the flux distribution, the induced rotor current, the designed high speed induction motor is analyzed by 3-D F.E.M.. Also, to identify the design specification, the performance characteristic is analyzed and estimated into the torque, the current and the output power at the static and the transient state.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.13-15
• /
• 2007

The washing machine needs high torque for large load variation, Interior permanent magnet synchronous motor(IPMSM) is proper to adapt the washing machine system. However, IPMSM can operate the lower output power than the other permanent magnet synchronous motor(PMSM) when the motor control by the conventional control. This paper suggests adaptive motor control for IPMSM and experiments the washing machine system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1084-1086
• /
• 2003

3-Phase BLDC Motor, which is generally used, has limited usage in high speed, due to pulsation torque occurring commutation and variable speed. To solve this problem, it is necessary to increase invariable, pole number, or the number of slots. Currently, due to rapid growth of semiconductor technology and trend toward smaller and cheaper production of switching device, multi-phase BLDC Motor for high speed, high output power is being actively pursued to produce. In this paper 7-Phase BLDC Motor drive system is designed and Vector modulator is studied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1049-1051
• /
• 2004

This paper presents the analysis and the design of IPMSM for high speed limit with constant torque. The characteristics of IPMSM are calculated by using d-q equivalent circuit having the parameters, such as current phase angle, d-q axis inductances, effective turns. These parameters affect the output characteristics. In this paper, the improved IPMSM to widen the operating speed limit are designed by the results.

• 전기학회논문지P
• /
• 제53권2호
• /
• pp.51-57
• /
• 2004

Vector control schemes are used in inverter-fed induction motor drives to obtain high performance. Crucial to the success of the vector control scheme is the knowledge of the instantaneous position of the rotor flux. However, the position of the rotor flux change with temperature and magnetic saturation of the motor. This variation cause deterioration of both steady state and dynamic operation of the motor drives. Performance degradation is in the form of input-output torque nonlinearity and saturation of the motor. Analytic expressions are derived to evaluate the effects due to parameter sensitivity. Also, dynamic response is shown by speed command with the variation of stator and rotor resistance.