• Journal of Korean Association for Spatial Structures
• /
• v.20 no.4
• /
• pp.53-62
• /
• 2020

This study examines the optimum shape of a trolley, the driving device of the retractable membrane roof. The closed-type trolley was determined as the model of the study, and a trolley composed of cylindrical-shaped inner and outer holders was selected as the basic model. Based on this model, a cylindrical-based optimal trolley model was proposed. In the basic trolley model, steel was used for the outer holder, and steel, titanium, and aluminum were used for the inner holder. In each case, the most economical shape for the external load of the basic model was newly proposed through the topology optimization process, and the finite element analysis results of the proposed model were compared to define the durability and economics. Here, topology optimization analysis and finite element analysis used the commercial software ANSYS. As a result of optimization, the volume of the outer holder of the trolley was reduced by 58.2% and the volume of the inner holder was reduced by 25.0% compared to the basic model. In the case of stress, a stress increase of 43.2 to 79.2% occurred depending on the material of the inner holder, but it was found to be significantly lower than the yield strength, thereby ensuring safety.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.2
• /
• pp.57-62
• /
• 2014

The biogas holder is composed of an outer membrane and an inner membrane which are subject to outdoor exposure and gas exposure respectively. The influence of weathering conditions on the photo-degradation of a biogas holder was investigated. Tests were performed under three different methods - outdoor exposure tests (Seosan, Arizona), accelerated tests (Xenon-are lamp) with the outer-membrane of biogas. Moreover, the changes in the aging process were monitored using color difference, gloss, the contact angle and an optical microscope. Changes in physical properties, such as decrease reduction in gloss, decrease in the contact angle, increase in color difference were observed in the aging process. The comparison between membrane 3B, 4B and membrane 5B under xenon-arc were discussed. Membrane 5B was very sensitive to ultraviolet (UV) ray. There were many difficulties in the outdoor exposure test due to acid rain, dust, and stain resistance.

• The korean journal of orthodontics
• /
• v.9 no.1
• /
• pp.23-35
• /
• 1979

The present study has the purpose of investigating various growth and developmental aspects of rabbit snout with the aid of metallic implantation and of improving on the indirect method of growth and developmental studies of its skull. Sixty-eight growing albino rabbits were used. A head holder, film holder, cephalometer, metallic implanting device and implant materials were designed and constructed by the author. Eight metallic pins were implanted with a metallic implanting device in the rabbit snout under general anesthesia. Two metallic pins were implanted on each side of the interfrontal suture and another two were put on each side of the internasal suture near the frontonasal suture. Serial cephalograms were taken with a two-week interval, using the head holder, film holder and cephalometer. Eight items of linear measurement were obtained from the film. On the base of the results of the study, the following conclusions are obtained: 1. The metallic implant method is better than the other indirect methods for growth and developmental studies of the rabbit skull. 2. Most of the vertical growth of the rabbit snout is due to sutural growth at the frontonasal suture and the horizontal growth is at the interfrontal and the internasal suture. 3. The vertical growth of the rabbit snout is greater than the horizontal growth. 4. The horizontal growth of the rabbit snout is greater at the nasal bone than at the frontal bone. 5. The amount of vertical growth of the rabbit snout is almost same at inner and outer side of the interfrontal and internasal suture line, 6. Growth rate of the sutural growth of the rabbit snout tends to decrease by the growth of the rabbit. 7. Implant materials do not disturb growth and development of the rabbit snout, except a slight trauma effect during the first week of metallic implantation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1389-1403
• /
• 1993

A procedure has be developed to optimize the product's tipping position in designing a die face for manufacturing automobile outer panels. Two design requirements are considered in optimizing the tipping position. One is to satisfy that all the points on the product should have a uniform distribution of drawing depths. The other is to guarantee that the user-specified area on the product should first contact with the binder wrap. The problem to satisfy the design requirements described above is analogous to the flatness calculation problem in the area of metrology if some constraints can be imposed. Thus the problem can be solved by the simulated annealing method, which is one of the optimization methods. The developed procedure was tested with the real die face design problem and the usefulness was verified by the diagram of the drawing depth.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.188-191
• /
• 2005

Two different coverlayers which is useful for an optical buffer and a mechanical protection made of not only UV resin but also polycarbonate coversheet were prepared on small form factor optical disks. Thin coverlayer of 10 ${\mu}m$ and thick coverlayer of 80 ${\mu}m$ were fabricated. 10 ${\mu}m$-thick coverlayer was coated using UV resin material by spin coating method for the flying optical head application. On the other hand, 80 ${\mu}m$-thick coverlayer using coversheet with the resin bonding material was prepared for the non-flying optical head application. Both cases, the thickness uniformity seem to be the primary prerequisite factor, and it was analyzed. Thickness of 10 ${\mu}m$-thick UV resin coverlayer could be controlled within ${\pm}0.2m$ range and 80 ${\mu}m$-thick coversheet could be controlled within ${\pm}3{\mu}m$ range. However, the yield of such thickness tolerance was not good. New design of metal housing holder and polycarbonate outer ring was adopted to diminish the ski-jump phenomenon. Specifically, the polycarbonate outer ring was very effective to reduce the ski-jump. However, it should be careful to maintain uniform edge between disk and ring for the perfect coverlayer.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.6
• /
• pp.88-96
• /
• 2006

The objective of this research works is to develop back panel dies of PDP TV with a large size. In order to design the geometry of the dies and an initial size of blank optimally, the finite element analysis has been carried out using AUTOFORM V4.2. The conner radius of the upper trimming area and the distance from the outer line of the blank holder to the outer line of the blank have been selected as design parameters to remove the wrinkling of the trimming area. The results of the analyses have been shown that a feasible product without wrinkles and skid lines can be obtained when the conner radius ranges from 6mm to 8mm and the distance lines in the range of 40-60mm. From the proposed design of the dies and an initial blank size, the final die set of the back panel has been successfully manufactured.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.2
• /
• pp.149-155
• /
• 2016

The purpose of this study is to develop special tools used to extend the tool life for the boom of heavy equipment. The boom of heavy equipment is manufactured by cutting the inner and outer surface with respect to the assembly site essential. In particular, when cutting the inner surface, entry of the tool is difficult owing to the limited size of the inner diameter and non circular cutting. In addition, the productivity is poor because the use of the cutting tool made of the SKH material. Therefore, it is necessary to develop a special tool for machining heavy equipment boom to extend tool life and to improve productivity. The special tool developed this study has the form of a holder and tip. The tip was created by applying a commercially available tungsten carbide insert.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.8
• /
• pp.194-202
• /
• 2002

Die design of bonnet drawing is composed of upper die, lower die and blank holder. It has been performed by checked and re-design method, which cause economic and financial loss. Nowadays, CAD/CAM system is excellent, but application is low. Therefore, in specific item, drawing die of bonnet outer draw by 3-D lay-out. In this study purpose, Bonnet drawing die is designed rapidly, correctly. It's method that shape modify to resemble. This purpose lead to 3-D Lay-Out. It is to react the standard die. In rule relation, input data change all of the shape.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.382-386
• /
• 2001

Die design of bonnet drawing is composed of upper die, lower die and blank holder. It has been performed by checked and re-design method, which cause economic and financial loss. Nowadays, CAD/CAM system is excellent, but Application is low. Therefore, in specific item, drawing die of bonnet outer draw by 3-D Lay-Out. In this study purpose, Bonnet drawing die is designed rapidly, correctly. It's method that shape modify to resemble. This purpose lead to 3-D Lay-Out. It is to react the standard die. In rule relation, input data change all of the shape

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.407-414
• /
• 2006

An X-ray diffractometer for spatially resolved X-ray diffraction measurements was developed to identify phase in the narrow (micron-scaled) region of high burn-up fuels and some nuclear materials. The micro-XRD was composed of an X-ray microbeam alignment system and a sample micro translation system instead of a normal slit and a fixed sample stage in a commercial XRD. The X-ray microbeam alignment system was fabricated with a microbeam concentrator having two Ni deposited mirrors, a vertical positioner, and a tilt table for the generation of a concentrated microbeam. The sample micro translation system was made with a sample holder and a horizontal translator, allowing movement of a specimen at $5{\mu}m$ steps. The angular intensity profile of the microbeam generated through a concentrator was symmetric and not distorted. The size of the microbeam was $4,000{\times}20{\mu}m$ and the spatial resolution of the beam was $47{\mu}m$ at the sample position. When the diffraction peaks were measured for a $UO_2$ pellet specimen by this system, the reproducibility ($2{\Theta}={\pm}0.01^{\circ}$) of the peaks was as good as a conventional X-ray diffractometer. For the cross section of oxidized titanium metal, not only $TiO_2$ in an outer layer but also TiO near an oxide-metal interface was observed.