• 한국해양공학회지
• /
• 제13권3B호
• /
• pp.47-55
• /
• 1999

A study on swirl chamber for diesel engine is to realize lower fuel consumption and exhaust emission than the current marketing engines. Author formerly reported the performance characteristics of small IDI diesel engine with swirl chamber by changing the jet passage area and its angle, and the depth and shape of the piston top cavity. Following after the first report, in this paper, the characteristics of fuel consumption, soot emission, and exhaust gas temperature were examined and analyzed after dimension of jet passage area expanded to $70.1mm^2$ The results were that the optimum values of the jet passage area depending on the depth of the piston top cavity were different at each engine speeds and loads, and in accordance with application of engine running conditions they were able to be selected as optimum dimensions of each design parameters.

• 한국세라믹학회지
• /
• 제32권1호
• /
• pp.17-24
• /
• 1995

The TEA complex polymeric sol was prepared by the alkoxide sol-gel method. The purpsoe of this experiment was to vefity the particle shape in the sol from the investigation of the rheological properties. TEA retarded hydrolysis rate by the reaction with alkoxide enough to make a stable transparent sol in the wide range of composition. From the results of the viscosity change with time, the optimum mole ratio for spinning was selected as 0.5 mole of TEA, 3 mole of H2O and the optimum viscosity was 104 cPs. The rheological behavior of the sol showed that the particle shape in the sol was linear, which was adequate for fiber drawing.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.741-745
• /
• 2001

The necessity of a Z-shape heat pipe may occur in a special application such as a cooling module for an electronic equipment having a limited accessible space. Either of the two end part works as evaporator or condenser and the length of the middle part is 200mm. The heat pipe was made of 3/8 inch copper tube having 60 spiral groove with screw angle of 10 degrees. Water and acetone were used as working fluids. The fill charge ratio of the working fluid was varied for different values of thermal loads. The thermal resistance was calculated based on the temperature measurements along the heat pipe axis. The maximum thermal loads were 80W for water and 100W for acetone heat pipe. The optimum fill charge ratio was identified through a series of experiments.

• 대한기계학회논문집A
• /
• 제24권5호
• /
• pp.1238-1245
• /
• 2000

One of the main causes of severe wear or crack initiation in wheel and rail is the contact stress due to wheel-rail contact. First, we obtain contact stress due to the rail mounting slope using the finite element method. Second, the shape design based on more reasonable contact stress analysis rather th~n a general Hertzian contact theory is investigated in order to reduce the contact stress. The optimum -design is performed using the simple 2-D finite element model and its results are verified by 311) finite element analysis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.360-364
• /
• 2001

본 논문에서는 최근의 진화적 구조최적화(ESO) 전략을 회전축의 형상최적화에 적용하였으며, 각 계산 스텝마다 단위 유한요소의 크기를 변경함으로써 기존의 방법보다 빠르고 정확한 최적형상에 수렴하는 새로운 방법을 제시하였다. 축요소의 직경을 시스템 설계변수로 하였으며, 축중량의 감소, 공진배율(Q-factor)의 감소 및 충분한 위험속도의 분리여유를 갖도록 목적함수를 설정하였다. 불평형응답 및 굽힙응력의 구속조건을 부가하였으며, 목적함수에 대한 설계변수의 감도해석을 수행하였다. 전동기축계에 대한 적용 결과로부터 주파수와 동적 구속조건하의 로터베어링 시스템에 대한 축 형상 최적화에 ESO법이 효과적으로 이용될 수 있음을 확인하였다.

• 설비공학논문집
• /
• 제13권10호
• /
• pp.1017-1024
• /
• 2001

The optimum shape of header part in a PFHE (parallel-flow heat exchanger) is studied. The optimal values of each geometric parameter are proposed according to their order of influence with varying the four important parameters (the injection angle of working fluid ($\Theta$), the shape of inlet(S), the location of inlet ($y_c/D_{in}$) and the height of the protruding flat tube ( $y_{b/}$ $D_{in}$ )). The optimal geometric parameters are as follows:$\Theta= -21^{\circ}C,\; S=Type\; A \;an\;y_b/D_{in}$/=0. The heat transfer rate of the optimum model, compared to that of the reference model, is increased by about 55%. The optimal geometric parameters ran be applicable to the Reynolds number ranging from 5,000 to 20,000.0.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.46-49
• /
• 2007

The purpose of this study is to develop the optimum shape of blank for the crank throw of large marine engine in order to reduce manufacturing cost and forging defects. The effects of the curvature radius and the height of wing part of blank selected as design variables on the defects and machining margin of final products after forging process were investigated using FEA. Based on the results, the optimum shape for the blank of the crank throw was proposed and verified by experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권5호
• /
• pp.678-685
• /
• 1999

A UBET program is developed for determining flash the optimum sizes of preform and initial billet in plane-strain closed-die forging. The program consists of forward and backward tracing processes. In the forward program, flash, die filling and forging load are predicted. In backward tracing process the optimum dimensions of initial billet and preform are determined from the final-shape data based on flash design. Experiments are carried out with pure plasticine billets ar room temperature. The theoretical predictions of forging load and flow pattern are in good agree-ment with the experimental results.

• 설비공학논문집
• /
• 제20권7호
• /
• pp.455-461
• /
• 2008

A reversed trapezoidal fin with variable fin base thickness is optimized using a two-dimensional analytical method. For the fin base boundary condition, instead of a constant temperature, heat transfer from the inside fluid to the fin base is considered. Heat loss from the fin tip is not ignored. The maximum heat loss, corresponding optimum fin effectiveness, fin length and base height are presented as a function of the fin base thickness, shape factor and volume.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.337-340
• /
• 2008

Magnesium alloy is expected to be widely used for mobile electronic appliances as well as automobile parts for its lightweight and EMI-shielding characteristics. In the present investigation, a Note-PC upper case made of magnesium alloy AZ31 sheet was developed by using the press forming technology at elevated temperature. Considering the press forming process and the formability of magnesium alloy sheet, the case shape and the press die was designed. The optimum forming condition was experimentally examined. Then the as-received magnesium alloy sheet was press-formed into the designed case shape under the optimum forming condition.