• 대한공간정보학회지
• /
• 제11권2호
• /
• pp.39-45
• /
• 2003

도로는 인류와 더불어 발전하여 근대화 되어왔고, 생산과 유통 등 경제적으로나 정치적 문화적으로도 중요한 기능을 하고 있으며, 교통체계 중에서 특히 우리의 생활에 중요한 교통시설이다. 그러나, 건설위주의 국가정책으로 인해 도로 시설물 관리가 과학적이고 체계적으로 수행되지 못하고, 기존 도로의 설계도가 훼손 분실되어 도로의 유지관리 차원에서 어려운 점이 많다. 이러한 경우, 기존의 측량방식으로 도로의 선형을 재현하기란 상당한 기간이 소요되며, 교통의 통제 등 많은 어려움이 따른다. 또한 도로 중심선의 3차원 좌표를 신속히 추출하기 위하여 위성측량방법을 이용할 경우, 터널과 같은 지역에서는 가시위성의 확보가 어려워서 관측이 되지 않는다. 따라서, 본 연구에서는 DGPS(Differential GPS)방법을 이용하여, 도로의 중심선 3차원 위치자료를 취득함과 동시에, 이러한 자료를 바탕으로 자료 취득이 불가능한 터널 내에서의 평면선형을 추출하고, 기존 설계도의 선형과 비교함으로써, 도로선형자료의 갱신과 유지관리 차원에서 앞으로 도로관리통합시스템을 구축하는데 있어서 도로선형 및 도로시설물의 위치를 효과적으로 관리 이용하는데 기여하고자 한다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 동계학술발표회 논문집
• /
• pp.277-278
• /
• 2007

Even though high NA, Hyper SIL system easily decline the optical performance even a little alignment error. Not only to overcome this instability but to maintain the high NA gain, we suggest a new system (Optimum SIL) which is a combination of each advantage of Hyper SIL and Hemi SIL. Simulation results shows that Optimum SIL system has much higher tolerance to various performance-lowering factors than Hyper SIL system even with a relatively small NA resignation.

• 대한전기학회논문지
• /
• 제43권2호
• /
• pp.303-311
• /
• 1994

Optimum conditions for the deposition of N-docosylquinolium-TCNQ ultrathin organic films using the Langmuir-Blodgett etchnique and the molecular orientation and alignment of the LB films were studied. The $\pi$-A isotherm of the N-docosylquinolium-TCNQ was measured at the air-water interface varying with the subphase temperature, subphase pH, compressing speed and amounts of solutions for spreading. The LB film was deposited under the surface pressure of 30mN.m and 45mN/m and other deposition conditions. The molecular orientation and alignment of the LB films were studied by the polarization absorption technique. The $\pi$-A isotherm showed that the stable N-docosylquinolium -TCNQ monolayer was formed on the water surface at the condition of 25$^{\circ}C$,pH 5.6, molecular density of 2.1${\times}$10S014T~2.6${\times}$10S014T/cmS02T. The LB film was deposited under the surface pressure of 45mN/m had better packing density, orientation and alignment than the film of 30mN/m.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권1호
• /
• pp.64-71
• /
• 2012

An efficient cooling system is an essential part of the electronic packaging such as a high-luminance LED lighting. A special technology, Pulsating Heat Pipe (PHP), can be applied to improve cooling of a sealed, explosion-proof LED light fixture. In this paper, the characteristics of the pulsating heat pipes in the imposed thermal boundary conditions of LED lightings were experimentally investigated and a PHP device that works free of alignment angle was investigated for cooling of explosion-proof LED lights. Five working fluids of ethanol, FC-72, R-123, water, and acetone were chosen for comparison. The experimental pulsating heat pipe was made of copper tubes of internal diameter of 2.1 mm, 26 turns. A variable heat source of electric heater and an array of cooling fins were attached to the pulsating heat pipe. For the alignment of the heating part at bottom, an optimum charging ratio (liquid fluid volume to total volume) was about 50% for most of the fluids and water showed the highest heat transfer performance. For the alignment of the heating part on top, however, only R-123 worked in an un-looped construction. This unique advantage of R-123 is attributed to its high vapor pressure gradient. Applying these findings, a cooling device for an explosion-proof type of LED light rated 30 W was constructed and tested successfully.

• Journal of Welding and Joining
• /
• 제27권1호
• /
• pp.85-89
• /
• 2009

Reflow process conditions were investigated for 0402 electric parts with Sn-3.0Ag-0.5Cu solders. Circle hole shape metal mask with 100 m thickness showed excellent printability. Self alignment abilities were 71% for 1005 chips, 52% for 0603 chips, and 3% for 0402 chips. Average joining strengos were 1990 gf for 1005 chips, 867 gf for 0603 chips, and 525 gf for 0402 chips. As mis-mounting angle increased, joining strength decreased. Considering self-alignment ability, mounting angle had to be under $5^{\circ}$ and contact area of the chips had to be over 40% for Pb-free soldering process for 0402 chips.

• Journal of electromagnetic engineering and science
• /
• 제14권4호
• /
• pp.329-331
• /
• 2014

A simple realization of an alignment-free wireless power transmission (WPT) system is presented in this letter. The WPT system consists of a transmitter with three reconfigurable modes corresponding to various controllable magnetic field directions in the azimuthal plane and an algorithm for the optimum mode selection carried by sensing the reflected voltage of the system. Twelve light emitting diodes (LEDs) are used to confirm the on- and off-state of LEDs powered wirelessly by the transmitter at every $15^{\circ}$ of the azimuthal plane. A criterion voltage from the reflected power of the system is found by using the correlation between the reflected voltage and the on- and off-state of the LEDs. Simply by continuous; monitoring of the voltage from the system, the system maintains power to the LEDs. The system is realized by MATLAB/Simulink and a National Instrument data acquisition device (DAQ) board. Measurements using the system show on-state LEDs in the azimuthal plane except at the angles of $60^{\circ}$, $75^{\circ}$, $180^{\circ}$, and $300^{\circ}$.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.28-35
• /
• 2010

In the display industry, COG bonding method is being applied to production of LCD panels that are used for mobile phones and monitors, and is one of the mounting methods optimized to compete with the trend of ultra small, ultra thin and low cost of display. In COG bonding process, electrical characteristics such as contact resistance, insulation property, etc and mechanical characteristics such as bonding strength, etc depend on properties of conductive particles and epoxy resin along with ACF materials used for COG by manufacturers. As the properties of such materials have close relation to optimization of bonding conditions such as temperature, pressure, time, etc in COG bonding process, it is requested to carry out an in-depth study on characteristics of COG bonding, based on which development of bonding process equipment shall be processed. In this study were analyzed the characteristics of COG bonding process, performed the analysis and reliability evaluation on electrical and mechanical characteristics of COG bonding using ACF to find optimum bonding conditions for ACF, and performed the experiment on bonding characteristics regarding fine pitch to understand the affection on finer pitch in COG bonding. It was found that it is difficult to find optimum conditions because it is more difficult to perform alignment as the pitch becomes finer, but only if alignment has been made, it becomes similar to optimum conditions in general COG bonding regardless of pitch intervals.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1943-1950
• /
• 2010

Superimposition of horizontal and vertical curves may hamper the ride comfort and the running stability of train and largely affect the maintenance cost. However, in many cases, it's not easy to make a track plan because of the fixed points (bridge, tunnel, turnout, catenary system, etc.) to be avoided due to the geographic conditions or to be passed for utilization of existing structures. In this study, when the horizontal and vertical curves are superimposed, in order to optimize the horizontal curve in aspect of the ride comfort, the object function $P_{CT}$ was developed and verified by vehicle dynamic analysis. Also, the solution algorithm for simplified evaluation method was presented.

• Nuclear Engineering and Technology
• /
• 제33권5호
• /
• pp.514-525
• /
• 2001

Optimum characteristics of digital X-ray sensor components were analyzed to develop intra- oral dental digital X-ray image sensor using indirect method. Parametric analysis was carried out to optimize the phosphor thickness and the fiber optic plate (FOP) coupling to charge coupled device (CCD). X-ray absorption and light diffusion in the phosphor layer were analyzed by the Monte Carlo method. Real time X-ray image was obtained with prototype X- ray image sensor using general CCD camera with 1∼10 Ip/mm resolution. It has been previously shown that large resolution degradation in X-ray images was caused by miss alignment of FOP to CCD and optical adhesive selection. In this study, we reported that X-ray image quality was greatly improved by using optimized characteristics of alignment device and phosphor thickness.

• 한국정보전자통신기술학회논문지
• /
• 제12권1호
• /
• pp.72-77
• /
• 2019

정보전달 매체 중 시각을 통하여 우리에게 정보를 제공해 주는 디스플레이는 직관적으로 정보를 전달해 줌으로써 매우 중요한 정보전달 수단이라고 할 수 있으며 액정표시장치는 디스플레이 중에서 가장 많이 보급되어 있는 정보전달기기라고 할 수 있다. 본 논문에서는 액정디스플레이 제작을 위하여 필수적인 러빙 기반 액정 배향 공정을 대체할 수 있는 공정으로서 solvent assisted micromolding을 연구하였으며 가장 일반적인 액정 배향막인 polyimide에 나노구조를 형성함으로써 균일하게 액정 배향을 달성하고자 하였다. Polyimide 나노구조 형성 시 공정 온도에 따라 용매에 의한 고분자 용해효과와 몰드의 나노구조 안으로 polyimide 분자의 모세관 효과 사이의 상보적 상관관계가 존재하였으며 최적온도 도출을 통해 높은 단차를 갖는 나노구조를 형성할 수 있었다. 이러한 나노구조는 액정 분자를 균일하게 배향할 수 있었으며 일정한 선경사각을 형성할 수 있음을 증명하였다.