• Clean Technology
• /
• v.21 no.2
• /
• pp.96-101
• /
• 2015

Hematite reduction using hydrogen was conducted and the various process parameters were closely observed. A lab scale fluidized bed unit was designed especially for this study. The optimal values of the gas velocity, reduction time and temperature were evaluated. The values which indicated the highest reduction rate were set as fixed parameters for the following tests starting with the reduction time of 30 minutes and 750 ℃ of temperature. Among these variables the one with the highest interest was the gas specific consumption. It will tell the amount of the gas which is required to achieve a reduction rate of over 90% at the optimal conditions. This parameter is important for the scale up of the lab scale unit. 1,500 Nm³/ton-ore was found to be the optimal specific gas consumption rate at which the reduction rates exhibit the highest values for hematite.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.775-780
• /
• 2016

Recently, photovoltaic industry needs a new design of Czochralski (Cz) process for higher productivity with reasonable energy consumption as well as solar cell's efficiency. If the process uses the large size reactor for increasing productivity, it is possible to produce a 12-inch, rather than the 8-inch. Also the continuous czochralski process method can be maximized to increase productivity. In this study, it was designed to improve the yield value of ingot with optimal condition which reduce consumption of electrical power. It has increased the productivity of the 12-inch ingot process condition by using CFD simulation. I have found optimal growth rate, by comparing each growth rate the interface shape, Temperature gradient, power consumption. As a result, the optimal process parameters of the growth furnace has been derived to improve for the productivity and to reduce energy. This study will contribute to the improvement of the productivity in the solar cell industry.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.05a
• /
• pp.38-39
• /
• 2019

Optimal route planning is the route planning to minimize voyage time or fuel consumption in a given ocean environment. Unlike the previous studies on weather routing, this study proposes an optimization method for the route planning to avoid the grounding risk in the coast. The route way-points were searched using Dijkstra algorithm, and then the optimization was performed to minimize fuel consumption by setting the optimization design parameter to the engine rpm. To set the engine rpm, a method to use the fixed rpm from the departure point to the destination point, and a method to use the rpm for each section by dividing the route were used. The ocean environmental factors considered for route planning were wind, wave, and current, and the depth information was utilized to compute grounding risk. The proposed method was applied to the ship passing between Mokpo and Jeju, and then it was confirmed that fuel consumption was reduced by comparing the optimum route and the past navigated route.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.674-682
• /
• 2017

This paper presents an optimal initial firing angle control based on the energy consumption and regenerative energy of a parallel multi-pulse thyristor dual converter for urban railway power substations. To prevent short circuiting the thyristor dual converter, a hysteresis band for maintaining a zero-current discontinuous section (ZCDS) is essential during mode changes. During conversion from the ZCDS to forward or reverse mode, the DC trolley voltage can be stabilized by selecting the optimal initial firing angle without an overshoot and slow response. However, the optimal initial firing angle is different depending on the line impedance of each converter. Therefore, the control algorithm for tracking the optimal initial firing angle is proposed to eliminate the overshoot and slow response of DC trolley voltage. Simulations and experiments show that the proposed algorithm yields the fastest DC voltage control performance in the transient state by tracking the optimal firing angle.

• The Journal of Fisheries Business Administration
• /
• v.23 no.2
• /
• pp.53-67
• /
• 1992

It has been recognized, virtually from the time of its inception, that fisheries economics, like other aspects of resource economics, should ideally be cast in capital-theoretic terms. The fish population or biomass can be viewed as a capital stock in that, like conventional or man-made capital, it is capable of yielding a sustainable consumption flow through time. This study is to introduce the optimal control theory which was extended from the theory of calculus of variations into the study of former static theory of fisheries economics started by Gordon (1954). The optimal control theory eliminated the inadequacies of the classical techniques to a large extent. From this point of view, this study, on the base of Schaefer model, summerizes most of major results achieved so far, but does so in a manner such that the links with capital theory are made transparent. This study explores two sets of problems. The first concerns the optimal approach to the equilibrium stock, i.e. the optimal investment policy. The second set of problems arises from the relaxation of the highly restrictive assumption of autonomy (i.e. the assumption that the parameters are independent of time), then concludes the relaxation of linearity assumption together with the complexities caused by that.

• Journal of the Korea Society of Computer and Information
• /
• v.4 no.1
• /
• pp.38-46
• /
• 1999

One of the tasks of maritime navigation is to decide upon the optimal navigation route that minimizes a vessals travel time and fuel consumption. Recently. ECDIS(Electronic Chart Display Information System) is used to decide the optimal navigation route and have expert knowledge of maritime navigation. In this paper, the system use $A^*$algorithm for optimal navigation route on ECDIS. But some problems is discovered in this situation. it requires many memory device and searching time. So this paper has tried to develope a advanced algorithm system that decides the optimal navigation route.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1014-1019
• /
• 2009

The optimal control system for heat source and HVAC system has been developed for minimizing energy consumption while maintaining the comfort of indoor thermal environment in terms of the environmental variables such as time varying indoor load and outdoor temperatures. The optimal set-points of control parameters are supply air temperature and chilled or hot water temperatures. The optimal control study has been implemented for biosafety laboratory by using TRNSYS simulation program in order to investigate energy performance for heat source and HVAC system.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.67-74
• /
• 1998

Reducing drag of vehicles are the main concern for the body shape designers in order to lower fuel consumption rate and to aid the driving stability. The drag of bluff bodies like transportation vehicles is mostly pressure drag due to the flow separation, which can minimized by controlling the location and size of the separation bubble. In the present study, the TURBO-3D code is incorporated with optimal algorithm based on analytical approximation method to obtain optimal afterbody shape of the MIRA Model corresponding to the lowest drag coefficient. For this purpose three mutually independent afterbody angles are chosen as design variables, while the drag coefficient is chosen as an objective function. It is demonstrated in the present study that an optimal body shape having lowest drag coefficient which is about $6\%$ lower than that of the original shape has been successfully obtained within number of iterations of the optimal design loop.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.46-51
• /
• 2007

The near-optimal control algorithm for central cooling system has been developed for minimizing energy consumption while maintaining the comfort of indoor thermal environment in terms of the environmental variables such as time varying indoor cooling load and outdoor temperatures. The optimal set-points of control parameters with near-optimal control are supply air temperature and chilled water temperature. This study has been done by using LapVIEW program with PID control in order to analyze the central cooling system energy saving.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.129-139
• /
• 2019

In order for a gun-launched guided projectile to glide to the maximum range, when to deploy the fin and start flight with guidance and control should be considered in range optimization process. This study suggests a solution to the optimal guidance problem for flight range maximization of the flight model of a guided projectile in vertical plane considering the aerodynamic properties. After converting the nonlinear Multi-Phase Optimal Control Problem to Two-Point Boundary Value Problem, the optimized guidance command and the best fin deployment timing are calculated by the proposed numerical method. The optimization results of the multiple flight rounds with various initial velocity and launch angle indicate that determining specific launch condition incorporated with the guidance scheme is of importance in terms of mechanical energy consumption.