• 한국유체기계학회 논문집
• /
• 제12권6호
• /
• pp.41-46
• /
• 2009

This paper deals with the operating-speed (high-speed) balancing of a refinery gasoline HDS (hydrodesulfurization) process recycle-gas 8-stages compressor rotor. A low-speed balancing condition of the rotor was measured as maintaining the G2.5 level. But an inspection run of operating-speed balancing condition, using tilting-pad journal bearings of actual use, showed that while it could be continuously-operated safely at a rated speed of 10,500 rpm, the rotor would not be able to run over 11,000 rpm as the vibration increased very sharply, approaching 11,000 rpm. In order to cure that a series of operating-speed balancing, which first calculated balance correction-weights by applying the influence coefficient measured and calculated at 10,500 rpm and then implemented correction works, was carried-out. The final operating-speed balancing results showed that the vibrations at the bearing pedestals represented very good levels of 0.2 mm/s by decreasing to as much as the 1/10 of the original vibrations and particularly, even at a targeted maximum continuous operating speed, MCS, of 11,500 rpm the vibrations represented about 1 mm/s, which is the operating-speed balancing vibration specification of API. Therefore, the expansion of MCS was successfully accomplished through the operating-speed balancing.

• 한국도로학회논문집
• /
• 제16권5호
• /
• pp.173-182
• /
• 2014

PURPOSES : The purpose of the study is to a) explore the operating speed of trucks on rural highways affected by road geometry, and thereby b) develop a predictive model for the operating speed of trucks on rural highways. METHODS : Considering that most of the existing studies have focused on cars, the current study aimed to predict the operating speed of trucks by conducting linear regression analysis on the speed data of trucks operating on the linear-curved-linear portions of the road as a single set. RESULTS : The operating speed in the plane curve portion increased with the length of the curve, and decreased with a lower vertical grade and a smaller curve radius. In the straight plane portion, the operating speed increased with a larger curve radius(upstream), and decreased with an increase in the change of the vertical grade, depending on the length of the vertical curve. CONCLUSIONS : This study developed estimation models of truck for operational speed and evaluated the degree of safety for horizontal and vertical alignments simultaneous. In order to represent whole area of the rural highway, the models should be ew-analyzed with vast data related with road alignment factor in the near future.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.148-151
• /
• 2005

This paper proposes a high speed interface using redundant multi-valued logic for high speed communication ICs. This circuit is composed of encoding circuit that serial binary data are received and converted into parallel redundant multi-valued data, and decoding circuit that convert redundant multi-valued data to parallel binary data. Because of the multi-valued data conversion, this circuit makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was designed using a 0.35${\mu}m$ standard CMOS Process. Proposed demultiplexer is achieved an operating speed of 3Gb/s with a supply voltage of 3.3V and with power consumption of 48mW. Designed circuit is limited by maximum operating frequency of process. Therefore, this circuit is to achieve CMOS communication ICs with an operating speed greater than 3Gb/s in submicron process of high of operating frequency.

• 대한교통학회지
• /
• 제22권7호
• /
• pp.25-32
• /
• 2004

현 도로설계기준은 설계속도가 주행속도를 대표하는 값임을 내재하고 있다. 역으로, 설계속도와 주행속도의 불일치는 현 도로설계가 주행 안전 및 쾌적감을 보장하지 못함을 의미하게 된다. 이런 맥락에서, 지방부 2차로 도로를 대상으로 운전자의 주행속도를 조사하여 설계속도와 주행속도 사이의 관계에 대해 검토하였다. 추가적으로, 주행속도로부터 도출된 수요 횡방향 미끄럼 마찰계수와 공급 횡방향 미끄럼 마찰계수를 주행 역학적 안전성 관점에서 비교하였다. 주행속도와 공급 설계속도를 비교한 결과, 평면 곡선반경 약 200m 이하 구간에서 주행속도가 공급 설계 속도를 초과하는 것으로 나타났으며, 평면 곡선반경에 작을수록 두 속도 사이의 차이가 큰 경향을 나타냈다. 유사하게, 평면 곡선반경 약 200m이하 구간에서 수요 횡방향 미끄럼 마찰계수가 공급 횡방향 미끄럼 마찰계수를 초과하는 것으로 나타났으며, 평면 곡선반경이 작을수록 두 값 사이의 차이가 큰 경향을 나타냈다.

• 한국유체기계학회 논문집
• /
• 제13권3호
• /
• pp.43-48
• /
• 2010

In this study rotordynamic characteristics of an air turbo-compressor (ATC) used in oxygen plant are analyzed and its operating-speed balancing is performed to solve the vibration trouble caused by rotor unbalance. Three dimensional model of the ATC rotor is completed and then analytical FE (finite element) model, which is verified by experimental modal testing, is developed. A rotordynamic analysis includes the critical map, Campbell diagram, and unbalance response, especially considering the pedestal housings supporting tilting pad bearings. A test run of operating-speed, using tilting-pad bearing of actual use, showed that the vibration level increased very sharply as approaching the rated speed. The operating-speed balancing specified by API 684 was carried out by using influence coefficient method. The results showed that the vibrations at the bearing pedestal housings represented good levels of 0.1 mm/s. From the test run and operating-speed balancing, the analytical results, that is, critical speeds are in good agreement with the test results and unbalance responses introducing the correction masses are similar to the as-is test responses in its aspect.

• 대한기계학회논문집A
• /
• 제20권9호
• /
• pp.2744-2751
• /
• 1996

In case of limited power supply, a rotating shaft system may not reach its operating speed that is greater than its critical speed, but the speed oscillates with small ampllitude near critical speed. As a result, it is considered that the operating mode plays an important role in the smooth start of machines. In order to investigate the dynamic behaviors of the rotating shaft system at the beginning stage, one has derived the equations of motion whose degrees of freedom is three, two translations and one rotation. The simultaneous differential equations are numerically solved by using runge-Kutta method, and thus the small time step length could be required corresponding to the stability of solution. Three types of operating modes dependent upon the driving torque rate have been numerically investigated according to the maximum displacement of shaft center. The first type of relation is linear, the second type is composed of two linear curves recommended by machine manufacturer, and the last one is the proposed torque curve reflecting the frequency response curve of one degree of freedom system. For the second type of modes, it is found that the optimal range of intermediate speed to the critical speed lies between 0.8 and 0.9. In addition to that, the maximum displacement can be reduced more if the third type of mode is utilized.

• 대한전기학회논문지:전력기술부문A
• /
• 제55권9호
• /
• pp.384-391
• /
• 2006

The harmonic currents generated along with the operating speed of electrical railroad traction are very difficult to analyze because of its nonlinear characteristics. This paper therefore presents probabilistic approach for the evaluation of harmonic currents about the operating speed of the arbitrary single traction. To use probabilistic method for railroad system, PDF(Probability Density Function) using measuring data based on the realistic h 따 monic currents per operating speed is calculated. Measuring data of harmonic current per operating speed is obtained using the result data of PSCAD/EMTDC dynamic simulation based on an IAT(Intra Airport Transit) in Incheon International Airport. The means(expected values) and variances of harmonic currents of single traction also are obtained by the PDF of the operating traction speed and harmonic currents. The uncertainty of harmonic currents can be calculated through the mean and variance of PDF. The probability of harmonic currents generated with the operating of arbitrary many tractions is calculated by the convolution of functions. The harmonics of different number of tractions are systematically investigated to assess the TDD(Total Demand Distortion) for the railroad system. The calculation of TDD was carried out using Monte-Carlo Simulations(MSCs) and the results of TDD evaluation of the power quality in the IAT power feeding system.

• 한국유체기계학회 논문집
• /
• 제14권4호
• /
• pp.38-44
• /
• 2011

This paper deals with the detail rotordynamic analysis for BB5 eight stages pump as development of API 610 BB5 type pump. Dry-run analytical model, not considering operating fluid, and wet-run analytical model, considering operating fluid are established. In addition, plain circular and pressure dam bearings are chosen and it was discussed that each bearing has an effect on dynamic characteristics of pump rotor system. A rotordynamic analysis includes the critical speed map, Campbell diagram, stability, and unbalance response. As results, it was predicted that rated speed of the pump rotor passes through 1st critical speed in dry-run condition regardless of bearings, however, it was verified that, in wet-run condition, the rotor system doesn't have critical speeds even if more than twice rated speed. Hence the resonance problem caused by the critical speeds does not happen since actual operating is in wet-run condition including operating fluid. As a result of unbalance response analysis, the pump rotor has stable vibration response at rated speed, regardless of operating fluid and the proposed bearing types.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.229-235
• /
• 2007

The KTX, which have opened the revenue service in April 2004, is operating in Kyoung-Bu high-speed line and electrified conventional Ho-Nam line, and the more the electrification are enlarged, the more the requirement of operating of high speed train would be increased. In this paper, the result of test run and evaluation on the suitability of operating high speed train in electrified conventional line between Dae-jeon and East Dae-gu was reviewed. Evaluation and analysis was executed in specific categories, such as operation & running performance of the train considering vibration characteristics based on UIC 518, ride comfort and current collection, and response sensitivity of ATS device for signalling from track facility. The result of this running test was evaluated and considered as a good practice for revenue operation of high speed train in electrified conventional line between Dae-jeon and Dae-gu.

• 한국도로학회논문집
• /
• 제10권2호
• /
• pp.57-67
• /
• 2008

현재 우리나라에서 도로 평면선형 설계를 위해 도로설계속도 개념을 사용하고 있다. 도로설계속도 개념은 단 한 개 도로 설계속도를 사용하기 때문에 도로 기하구조 수준이 일정해진다는 강점을 갖고 있으나, 도로 건설 후 그 도로를 주행하는 실제 차량 속도가 설계속도와 달리 나타날 수 있다는 약점을 갖고 있기도 하다. 본 연구에서는 이 약점을 보완하기 위해, 이미 여러 나라에서 사용 중인 주행속도 예측모형에 근거한 평면 선형설계기법을 제안한다. 본 연구에서는 이를 위해 우리나라 전역에서 표본을 선택하여 차량 속도조사를 수행했고, 속도에 영향을 미치는 도로설계요소를 통계분석을 통해 선정하여 양방향 2차로와 4차로 일반국도에 대한 차량 주행속도 모형을 제시했으며, 그 모형을 도로 평면선형설계에 적용하는 과정을 제시했다. 한편 새로운 기법에 대한 유효성을 밝히기 위한 실제 사례분석에서 새로운 기법은 기존 기법이 갖고 있는 약점을 해소하는 것으로 밝혀졌다. 향후 우리나라 도로 건설 사업에서 본 연구에서 제안한 평면선형 설계기법을 적용하면 도로 투자 효율성이 높아지고, 더 높은 설계일관성을 확보할 수 있을 것으로 판단한다.