• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.226-235
• /
• 1999

To investigate SPICE noise model and the behavior of its parameters, 1/f noise of NMOS devices fabricated by BiCMOS process is measured and compared to the various noise models and measured results. For the long channel devices, bias dependence of the drain current noise power spectral density $S_{Id}$ of NMOS is similar to the previous results. Equivalent gate noise power spectral density $S_{Vg}$ shows weak dependence on the gate and drain voltages in long channel NMOS as the previous results. However, it is shown that most of published noise models are difficult to apply to short channel devices. Therefore, in this study, with comparison of our experimental results, we have tried to find the model of 1/f noise, appropriate for our NMOS device fabricated by BiCMOS process.

• Journal of electromagnetic engineering and science
• /
• v.6 no.1
• /
• pp.30-35
• /
• 2006

This paper describes fully integrated low phase noise MMIC voltage controlled oscillators(VCOs). The Asymmetrical Inductance Tank VCO(AIT-VCO), which optimize the shortcoming of the previous tank's inductance optimization approach, has lower phase noise performance due to achieving higher equivalent parallel resistance and Q value of the tank. This VCO features an output power signal in the range of - 11.53 dBm and a tuning range of 261 MHz or 15.2 % of its operating frequency. This VCO exhibits a phase noise of - 117.3 dBc/Hz at a frequency offset of 100 kHz from carrier. A phase noise reduction of 15 dB was achieved relative to only one spiral inductor. The AIT-VCO achieved low very low figure of merit of -184.6 dBc/Hz. The die area, including buffers and bond pads, is $0.9{\times}0.9mm^2$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2002.11a
• /
• pp.111-116
• /
• 2002

With the proliferation of nonlinear loads such as personal computers in an educational office building, high neutral harmonic currents have been observed. High neutral currents in three-phase four-wire distribution power systems can cause overloaded neutral conductors, overloaded transformers, voltage distortion, common mode noise, and malfuntion of protective equipment. On-site measurements of harmonic currents and voltages were made and the corresponding equivalent circuits was developed. The circuit model under study was simulated numerically and graphically through the use of the software MATLAB.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.10
• /
• pp.895-901
• /
• 2013

Last blades of LP turbine in nuclear power plant are the highly damaged part and suffered from nozzle steam impulses during the turbine operation. Nozzle impulse is known as a common cause of damage or failure in the turbine blade and results from steam flow distortions due to uneven steam flow patterns between the stationary blade vanes. If impulse force was continuously acting on the blade for a long time, crack or wear will occur in weak parts such as root. So, it is important to know variation of nozzle impulse during the blade moving. But there is no way to measure and estimate the magnitude and direction of nozzle impulse. Therefore, this study was performed to know the variation of nozzle impulse force according to the positions of the blade and to obtain blade equivalent force and torque. This results can be used for blade stress estimation.

• Korean Institute of Interior Design Journal
• /
• v.14 no.3 s.50
• /
• pp.191-198
• /
• 2005

The present study is a preliminary research improving the dwelling quality of one-room type multi-family housings around the university campus. The purpose of the study is to investigate the present condition of Indoor noise level using · residents' responses and field measurements. The respondents are 104 residents living in one-room type multi-family housings. The field measurements on equivalent noise level of indoor and outdoor were carried out in 6 subject house units during the $26th\~28th$ of November 2002. The results are as follows. 1) The residents show relatively non-positive responses at evening and night on the present condition of indoor noise. 2) They answer 'living equipment foise' and 'water hammer' as major types of indoor noise of house unit. 3) Outdoor noise levels, basic factor of noise environment in 6 subject buildings were distributed $52.8\~65.3dB(A)Leq_{5min}$ and were inappropriate to the standard for environmental noise, $55 dB(A)Leq_{5min}$. 4) Indoor noise levels of subject house units were measured as $27.5\~63.5dB(A)Leq_{5min}$, the average of each house unit except one house unit was higher than the level feeling as noise, 40dB(A). 5) It was found that the differences of indoor noise levels between subject house units were caused by 'residents' living noise', 'living equipment noise', 'water hammer', and 'walking and talking noise in stairs and corridors'. 6) Therefore, it is required to plan for improving the quality of noise environment in one-room type multi-family housing around the campus. For example, soundproof construction (including double window with pair glass and balcony), outdoor garden with trees and water for increasing natural sound, interior materials with sound absorbing power to absorb living noise, soundproof pipe or double surface pipe for decreasing 'water hammer', and noiseproof floors, etc. are required.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.226-231
• /
• 1999

Pyroelectric infrared sensors have been fabricated using P(VDF/TrFE) film with pyroelectric effect. The weight percent and thickness of the poled P(VDF/TrFE) film are 75/25 percent and $25\;{\mu}m$ respectively. For easier fabrication and connection method new top and bottom electrodes design was adapted for human body detecting pyroelectric infrared sensor. An aluminum infrared absorption electrode and bottom electrode were deposited by thermal evaporator. And the device was mounted in TO-5 housing to detect infrared light of $5.5{\sim}14\;{\mu}m$ wavelength. The responsibility, NEP (noise equivalent power) and specific detectivity $D^*$ of the device were $9.62{\times}10^5\;V/W$, $3.95{\times}10^{-7}\;W$ and $5.06{\times}10^5\;cm/W$ under emission energy of $13\;{\mu}W/cm^2$ respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.5
• /
• pp.863-871
• /
• 2003

In this paper, we design a high stable Ku-band phase-locked dielectric resonant microwave oscillator with the gate voltage controls of p-HEMT. By adapting the nonlinear equivalent elements which affects phase noise of microwave oscillator, we optimize the nonlinear elements of p-HEMT to have low phase noise operation. Using the scattering parameters according to bias voltages, we designed the gate voltage control microwave dielectric resonant oscillator and phase-locked loop circuits is applied to have the high stable operations. Designed microwave oscillator as a local oscillator of digital microwave communication shows that output power is 9.17dBm at 10.75GHz and it's phase noise is -88dBc/Hz at 10KHz offset frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.12A
• /
• pp.1136-1146
• /
• 2005

In this paper, the radiative electric field intensity due to the communication signal and conductive noise is calculated in overhead medium voltage power lines for power line communication. The input impedance is calculated by means of 2 port equivalent model of medium voltage power line network and basic transmission line theory. And then, currents is calculated by calculated input impedance and finally, the emissive electric field is calculated. The input impedance appears like a standing wave form with a fixed cycle because high reflection at the input terminal due to the characteristic impedance of medium voltage power line is very large. A calculated current and radiative electric field also appears like this form. From the measurement results, the measured results are very similar to the calculated results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.51-55
• /
• 1995

본 연구에서는 회전동력전달계의 진동특성을 해석하고 이를 설계자료로 이용하기 위하여, 계 전체의 유효강성행렬 (effective stiffness matrix)을 실험적으로 결정할 수 있는 방법을 제안하였다. 이것은 비교적 측정이 용인한 관성행렬이 알려져 있다고 가정한 경우 기존의 선형 모델링을 그대로 이용하고, 위의 모든 기계요소의 해석이 불가능한 강성들을 포함한 등가강성(equivalent stiffness)으로 구성된 계의 유효강성행렬을, 실험에 의해 얻어진 계의 여러 작동상황과 이에 따른 고유진동수에 매칭(matching)시켜 결정하는 것이다. 또한, 이의 검증을 위하여 유성기어와 클러치로 이루어진 가상의 동력전달계를 구성하고 이의 시뮬레이션 결과를 이용하여, 유효강성 결정법을 통해 얻어진 등가강성들과 실제값들의 비교함으로서 그 신뢰도를 추정하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.4
• /
• pp.15-22
• /
• 2004

This paper presents the channel analysis considering power distribution network(PDN) system of PCB. For achieve the target PDN system we proposed the useful design approach for acquiring the characteristic target of power distribution network in overall frequency ranges. The proposed method is based on the hierarchical approach related to frequency ranges and the path-based equivalent circuit model to consider the interference of the current paths between the decoupling capacitors and the board through it is a lumped model for fast and easy calculation, experimental results show that the proposed model is almost as precise as the numerical analysis. The analysis of PDN system shows that although the effective inductance of package dominatly affects the power noise and the signal transfer through data channel, the board PDNs also can not be neglected for achieving the accurate channel signaling. Therefore, we must design concurrently the chip, package, and board from the initial spec design of high speed digital system.